Meso/micro scale milling for micro-manufacturing

International Journal of Mechatronics and Manufacturing Systems

Volumn 1, Issue 1, 2008, Pages 23-42

  Dhanorker, A ^a   Ozel T ^a  

^a DEPARTMENT OF INDUSTRIAL AND SYSTEMS ENGINEERING   (United States)

Author keywords

finite element modelling; micro milling; minimum chip thickness; size effect

Indexed keywords

EID: 84961561187     PISSN: 17531039     EISSN: 17531047     Source Type: Journal    
DOI: 10.1504/IJMMS.2008.018273     Document Type: Article

References (29)

1. Alting, L., Kimura, F., Hansen, H.N. and Bissacco, G. (2003) ‘Micro engineering’, Annals of the CIRP, Vol. 52, No. 2, pp.635–657.
2. Bao, W.Y. and Tansel, I.N. (2000a) ‘Modeling micro-end-milling operations. Part I: analytical cutting force model’, International Journal of Machine Tools and Manufacture, Vol. 40, pp.2155–2173.
3. Bao, W.Y. and Tansel, I.N. (2000b) ‘Modeling micro-end-milling operations. Part II: Tool run-out’, International Journal of Machine Tools and Manufacture, Vol. 40, pp.2175–2192.
4. Bao, W.Y. and Tansel, I.N. (2000c) ‘Modeling micro-end-milling operations. Part III: Influence of tool wear’, International Journal of Machine Tools and Manufacture, Vol. 40, pp.2193–2211.
5. de Chiffre, L., Kunzmann, H., Peggs, G.N. and Lucca, D.A. (2003) ‘Surfaces in precision engineering, microengineering and nanotechnology’, Annals of the CIRP, Vol. 52, No. 2, pp.561–577.
6. Dornfeld, D., Min, S. and Takeuchi, Y. (2006) ‘Recent advances in mechanical micromachining’, Annals of the CIRP, Vol. 55, No. 2, pp.745–768.
7. Dow, T.A., Miller, E.L. and Garrard, K. (2004) ‘Tool force and deflection compensation for small milling tools’, Precision Engineering, Vol. 28, pp.31–45.
8. Friedrich, C.R. and Vasile, M.J. (1996) ‘Development of the micro-milling process for high-aspect-ratio microstructures’, Journal of Microelectromechanical Systems, Vol. 5, No. 1, pp.33–38.
9. Ikawa, N., Shimada, S. and Tanaka, H. (1992) ‘Minimum thickness of cut in micromachining’, Nanotechnology, Vol. 3, No. 1, pp.6–9.
10. Johnson, G.R. and Cook, W.H. (1983) ‘A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures’, Proceedings of the 7th International Symposium on Ballistics, The Hague, The Netherlands, pp.541–547.
11. Kim, C.J., Bono, M. and Ni, J. (2002) ‘Experimental analysis of chip formation in micro-milling’, Transactions of NAMRI/sMe, Vol. 30, pp.247–254.
12. Kim, C.J., Mayor, J.R. and Ni, J. (2004) ‘A static model of chip formation in microscale milling’, ASME Journal of Manufacturing Science and Engineering, Vol. 126, pp.710–718.
13. Lee, K. and Dornfeld, D.A. (2002) ‘An experimental study on burr formation in micro milling aluminum and copper’, Transactions of NAMRI/SME, Vol. xxx, pp.255–262.
14. Liu, X., DeVor, R.E. and Kapoor, S.G. (2006) ‘An analytical model for the prediction of minimum chip thickness in micromachining’, ASME Journal of Manufacturing Science and Engineering, Vol. 128, pp.474–481.
15. Lucca, D.A. and Seo, Y.W. (1993) ‘Effect of tool edge geometry on energy dissipation in ultra precison machining’, Annals of the CIRP, Vol. 42, No. 1, pp.83–86.
16. Madou, M. (1997) Fundamentals of Microfabrication, CRC Press, Boca Raton, Florida, USA.
17. Martellotti, M.E. (1945) ‘An analysis of the milling process, part ii – down milling’, Transaction of the ASME, Vol. 67, pp.233–251.
18. Masuzawa, T. and Tonshoff, H.K. (1997) ‘Three-dimensional micro-machining by machine tools’, Annals of the CIRP, Vol. 46, No. 2, pp.621–628.
19. Melkote, S.N. and Endres, W.J. (1998) ‘The importance of including the size effect when modeling slot milling’, ASME Journal of Manufacturing Science and Engineering, Vol. 120, pp.68–75.
20. Özel, T. and Altan, T. (2000) ‘Process simulation using finite element method- prediction of cutting forces, tool stresses and temperatures in high-speed flat end milling process’, International Journal of Machine Tools and Manufacture, Vol. 40, No. 5, pp.713–738.
21. Schaller, T., Bohn, L., Mayer, J. and Schubert, K. (1996) ‘Microstructure grooves with a width of less than 50 micrometer cut with ground hard metal micro end mills’, Precision Engineering, Vol. 23, pp.229–235.
22. Schmidt, J. and Tritschler, H. (2004) ‘Micro cutting of steel’, Microsystem Technologies, Vol. 10, pp.167–174.
23. Schmidt, J., Spath, D., Elsner, J., Huentrup, V. and Tritschler, H. (2002) ‘Requirements of an industrially applicable microcutting process for steel micro-structures’, Microsystem Technologies, Vol. 8, pp.402–408.
24. Uhlmann, E. and Schauer, K. (2005) ‘Dynamic load and strain analysis for the optimization of micro end mills’, Annals of the CIRP, Vol. 54, No. 1, pp.75–78.
25. Vasile, M.J., Friedrich, C.R., Kikkeri, B. and McElhannon, R. (1999) ‘Micrometer-scale machining: tool fabrication and initial results’, Precision Engineering, Vol. 19, pp.180–186.
26. Vogler, M.P., Liu, X., Kapoor, S.G., Devor, R.E. and Ehmann, K.F. (2002) Development of Meso-Scale Machine Tool (Mmt) Systems, Technical Paper, Society of Manufacturing Engineers, MS02–181.
27. Vogler, M.P., DeVor, R.E. and Kapoor, S.G. (2004a) ‘On the modeling and analysis of machining performance in micro-endmilling, Part I: Surface generation’, ASME Journal of Manufacturing Science and Engineering, Vol. 126, pp.685–694.
28. Vogler, M.P., DeVor, R.E. and Kapoor, S.G. (2004b) ‘On the modeling and analysis of machining performance in micro-endmilling, Part II: Cutting force prediction’, ASME Journal of Manufacturing Science and Engineering, Vol. 126, pp.695–705.
29. Weule, H., Huntrup, V. and Tritschle, H. (2001) ‘Micro-cutting of steel to meet new requirements in miniaturization’, Annals of the CIRP, Vol. 50, No. 1, pp.61–64.