The importance of including size effect when modeling slot milling

Journal of Manufacturing Science and Engineering, Transactions of the ASME

Volumn 120, Issue 1, 1998, Pages 68-75

  Melkote, S N ^a,b   Endres, W J ^a,c  

^a University of Illinois at Urbana Champaign   (United States)

^b GEORGIA INSTITUTE OF TECHNOLOGY   (United States)

^c UNIVERSITY OF MICHIGAN   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTATIONAL GEOMETRY; COMPUTER SIMULATION; CUTTING TOOLS; FORCE MEASUREMENT; MATHEMATICAL MODELS; SLOTTING;

CUTTING FORCE VARIATION; MECHANISTIC FORCE ANALYSIS; PERIPHERAL END MILLING MODELS; STEADY STATE SLOTTING;

MILLING (MACHINING);

EID: 0031996720     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.2830112     Document Type: Article

References (15)

1. Backer, W. R., Marshall, E. R., and Shaw, M. C, 1952, “The Size Effect in Metal Cutting,” ASME Transactions, Vol. 74, pp. 61-72.
2. Elbestawi, M. A., Ismail, F., Du, R., and Ullagaddi, B.C., 1991, “Modeling Machining Dynamics Including Damping in the Tool-Workpiece Interface,” Proceedings, ASME Symposium on Tribological Aspects in Manufacturing, ASME Winter Annual Meeting, PED-Vol. 54/TRIB-Vol. 2, pp. 253-263.
3. Endres, W. J., DeVor, R. E., and Kapoor, S. G., 1995, “A Dual-Mechanism Approach to the Prediction of Machining Forces: Part I and Part 2,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 117, pp. 526-541.
4. Fussell, B. K., and Srinivasan, K., 1989, “An Investigation of the End Milling Process Under Varying machining Conditions,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 111, pp. 27-36.
5. Kline, W. A., and DeVor, R. E., 1983, “The Effect of Runout on Cutting Geometry and Forces in End Milling,” International Journal of Machine Tool Design and Research, Vol. 23, No. 2/3, pp. 123-140.
6. Kolarits, F. M., and DeVries, W. R., 1990, “A Mechanistic Dynamic Model of End Milling for Process Controller Simulation,” Proceedings, ASME Symposium on Fundamental Issues in Machining, ASME Winter Annual Meeting, PEDVol. 43, pp. 229-244.
7. Melkote, S. N., 1993, “The Modeling of Surface Texture in End Milling Process,” Ph.D. Thesis, Michigan Technological University.
8. Sabberwal, A. J. P., 1961, “Chip Section and Cutting Force During the Milling Operation,” Annals of the CIRP, Vol. 10, No. 3, pp. 197-203.
9. Sutherland, J. W., 1988, “A Dynamic Model of the Cutting Force System in the End Milling Process,” Proceedings, ASME Symposium on Sensors and Controls for Manufacturing, PED-Vol. 33, pp. 53-62.
10. Tlusty, J., and MacNeil, P., 1975, “Dynamics of Cutting Forces in End Milling,” Annals of the CIRP, Vol. 24, No. 1, pp. 21-25.
11. Tlusty, J., 1985, “Chapter 3: Machine Dynamics, “Handbook of High Speed Machining Technology, R. I. King, ed., Chapman and Hall, N.Y., pp. 48-153.
12. Wang, J. J-J, Liang, S. Y., and Book, W. J., 1994, “Convolution Analysis of Milling Force Pulsation,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 116, pp. 17-25.
13. Yellowley, I, 1985, “Observations on the Mean Values of Forces, Torque and Specific Power in the Peripheral Milling Process,” International Journal of Machine Tool Design and Research, Vol. 25, No. 4, pp. 337-346.
14. Yellowley, I, 1988, “A Note on the Significance of the Quasi-Mean Resultant Force and the Modeling of Instantaneous Torque and Forces in Peripheral Milling Operations,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 110, pp. 300- 303.
15. Yucesan, G., Xie, Q., and Bayoumi, A. E., 1993, “Determination of Process Parameters Through a Mechanistic Force Model of Milling Operations,” International Journal of Machine Tools and Manufacture, Vol. 33, No. 4, pp. 627.