A static model of chip formation in microscale milling

Journal of Manufacturing Science and Engineering

Volumn 126, Issue 4, 2004, Pages 710-718

  Kim, Chang Ju ^a   Mayor, J Rhett ^a   Ni, Jun ^a  

^a UNIVERSITY OF MICHIGAN   (United States)

Author keywords

Edge Radius Effect; Intermittent Chip Formation; Micromanufacturing; Micromilling; Minimum Chip Thickness

Indexed keywords

COMPUTER SIMULATION; CUTTING; DATA REDUCTION; FABRICATION; HARDNESS; MICROSTRUCTURE; STRENGTH OF MATERIALS; THICKNESS MEASUREMENT;

EDGE-RADIUS EFFECT; INTERMITTENT CHIP FORMATION; MICROMANUFACTURING; MICROMILLING; MINIMUM CHIP THICKNESS;

MILLING (MACHINING);

EID: 14744284250     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1813475     Document Type: Review

References (22)

1. Kussul, E. M., Rachkovskij, D. A., Baidyk, T. N., and Talayev, S. A., 1996, "Micromechanical Engineering: A Basis for the Low-Cost Manufacturing of Mechanical Microdevices Using Microequipment," J. Micromech. Microeng., 6, pp. 410-425.
2. Masuzawa, T., and Tonshoff, H. K., 1997, "Three-Dimensional Micromachining by Machine Tools," CIRP Ann., 46, pp. 621-628.
3. Vasile, M. J., Friedrich, C. R., Kikkeri, B., and Mcelhannon, R., 1996, "Micrometer-Scale Machining: Tool Fabrication and Initial Results," Precision Eng., 19, pp. 180-186.
4. Weck, M., Fischer, S., and Vos, M., 1997, "Fabrication of Microcomponents Using Ultraprecision Machine Tools," Nanotechnology, 8, pp. 145-148.
5. Friedrich, C., Coane, P., Goettert, J., and Gopinathin, N., 1998, "Direct Fabrication of Deep X-Ray Lithography Masks by Micromechanical Milling," Precision Eng., 22, pp. 164-173.
6. Schaller, T., Bohn, L., Mayer, J., and Schubert, K., 1999, "Microstructure Grooves With a Width of Less Than 50 Micrometer Cut With Ground Hard Metal Micro End Mills," Precision Eng., 23, pp. 229-235.
7. Weule, H., Huntrup, V., and Tritschle, H., 2001, "Micro-Cutting of Steel to Meet New Requirements in Miniaturization," CIRP Ann., 50, pp. 61-64.
8. Chuzhoy, L., Devor, R. E., Kapoor, S. G., Beaudoin, A. J., and Bammann, D. J., 2003, "Machining Simulation of Ductile Iron and Its Constituents, Part 1: Estimation of Material Model Parameters and Their Validation," ASME J. Manuf. Sci. Eng., 125, pp. 181-191.
9. Chuzhoy, L., and Devor, R. E., 2003, "Machining Simulation of Ductile Iron and Its Constituents, Part 2: Numerical Simulation and Experimental Validation of Machining," ASME J. Manuf. Sci. Eng., 125, pp. 192-201.
10. Vogler, M. P., Devor, R. E., and Kapoor, S. G., 2003, "Microstructure-Level Force Prediction Model for Micro-Milling of Multi-Phase Materials," ASME J. Manuf. Sci. Eng., 125, pp. 202-209.
11. Kim, C.-J., Bono, M., and Ni, J., 2002, "Experimental Analysis of Chip Formation in Micro-Milling," Trans. NAMRI/SME, 30, pp. 247-254.
12. Martellotti, M. E., 1941, "An Analysis of the Milling Process," Trans. ASME, 63, pp. 677-700.
13. Komanduri, R., 1971, "Some Aspects of Machining With Negative Rake Tools Simulating Grinding," Int. J. MTDR, 11, pp. 223-233.
14. Abdelmoneim, M. E., and Scrutton, R. F., 1973, "Post-Machining Plastic Recovery and the Law of Abrasive Wear," Wear, 24, pp. 1-13.
15. Basuray, P. K., Misra, B. K., and Lal, G. K., 1977, "Transition From Ploughing to Cutting During Machining With Blunt Tools," Wear, 43, pp. 341-349.
16. Yuan, Z. J., Zhou, M., and Dong, S., 1996, "Effect of Diamond Tool Sharpness on Minimum Cutting Thickness and Cutting Surface Integrity in Ultraprecision Machining," J. Mater. Process. Technol., 62, pp. 327-330.
17. Merchant, M. E., 1944, "Basic Mechanics of the Metal-Cutting Process," ASME J. Appl. Mech., 12, pp. 168-175.
18. Nakayama, K., and Tamura, K., 1967, "Size Effect in Metal-Cutting Force," ASME Papers, Vol. 67-PROD-9, pp. 1-8.
19. Abdelmoneim, M. E., and Scrutton, R. F., 1974, "Tool Edge Roundness and Stable Build-up Formation in Finish Machining," ASME J. Eng. Ind., 96, Ser B, pp. 1258-1267.
20. Lucca, D. A., and Seo, Y. W., 1993, "Effect of Tool Edge Geometry on Energy Dissipation in Ultraprecision Machining," CIRP Ann., 42, pp. 83-86.
21. Waldorf, D. J., Devor, R. E., and Kapoor, S. G., 1998, "A Slip-Line Field for Ploughing During Orthogonal Cutting," ASME J. Manuf. Sci. Eng., 120, pp. 693-699.
22. Torrence, C., and Compo, G. P., 1998, "A Practical Guide to Wavelet Analysis," Bull. Am. Meteorol. Soc., 79, pp. 61-78.