Computational Welding Mechanics: Thermomechanical and Microstructural Simulations

Computational Welding Mechanics: Thermomechanical and Microstructural Simulations

Volumn , Issue , 2007, Pages 1-231

  Lindgren, Lars Erik ^a  

^a NONE

Author keywords

[No Author keywords available]

Indexed keywords

EID: 84903498643     PISSN: None     EISSN: None     Source Type: Book    
DOI: 10.1533/9781845693558     Document Type: Book

References (441)

1. Lindgren L.-E., Carlestam A., Jonsson M. Computational model of flame-cutting. ASME Journal of Engineering Materials and Technology 1993, 115:440-445.
2. Adams V., Askenazi A. Building Better Products with Finite Element Analysis 1999, OnWord Press.
3. Lindgren L.-E., Runnemalm H., Nasstrom M.O. Simulation of multipass welding of a thick plate. International Journal for Numerical Methods in Engineering 1999, 44(9):1301-1316.
4. Zacharia T., et al. Modeling of fundamental phenomena in welds. Modelling and Simulation in Materials Science and Engineering 1995, 3:265-288.
5. Akhlagi M., Goldak J. Computational Welding Mechanics 2005, Springer.
6. Radaj D. Schweissprozess-simulation. Grundlagen und Anwendungen (in German). Fachbuche Schweisstechnik 1999, 141:193.
7. Radaj D. Welding residual stresses and distortion. Calculation and measurement 2003, DVS-Verlag.
8. Ramirez M., Trapaga G., Mckelliget J. A comparison between two different numerical formulations of welding arc simulation. Modelling and Simulation in Materials Science and Engineering 2003, 11(4):675-695.
9. Zhu P. Computer simulation of gas metal welding arcs 1998, Pine Mountain, Georgia: American Welding Society.
10. Debroy T. Mathematical Modelling of Weld Phenomena 5. Mathematical modelling of fluid flow and heat transfer in fusion welding 1999, IOM Communications, Seggau, Austria.
11. Pavlyk V., Dilthey U. Simulation of weld solidification microstructure and its coupling to the macroscopic heat and fluid flow modelling 2004, S33. Vol. 12. http://www.iop.org/EJ/abstract/0965-0393/12/1/503.
12. Do-Quang M., Amberg G. Mathematical Modelling of Weld Phenomena 7. Modelling of time-dependent 3D weld pool flow. 2003, Graz, Austria.
13. Winkler C., et al. The effect of surfactant redistribution on the weld pool shape during GTA-welding. Science and Technology of Welding and Joining 2000, 5:1-13.
14. Pavlyk V., Dilthey U. Mathematical Modelling of Weld Phenomena 5. A numerical and experimental study of fluid flow and heat transfer in stationary GTA weld pools. 1999, IOM Communications, Seggau, Austria.
15. Sudnik W., Radaj D., Erofeew W. Computerized simulation of laser beam weld formation comprising joint gaps. Journal of Physics D: Applied Physics 1998, 31(24):3475.
16. Sudnik W., et al. Numerical simulation of weld pool geometry in laser beam welding. Journal of Physics D: Applied Physics 2000, 33(6):662.
17. LundbÄCk A., Runnemalm H. Validation of three dimensional finite element model in electron beam welding of Inconel 718. Science and Technology of Welding and Joining 2005, 10(6):717-724.
18. Sheng I., Chen Y. Modeling welding by surface heating. ASME Journal of Engineering Materials and Technology 1992, 114(4):439-449.
19. Chen Y., Sheng I. Heat and Mass Transfer in Solidification Processing. On the solid-fluid transition zone in welding analysis. 1991, ASME, 21-33.
20. Felippa C., Park K., Farhat C. Partitioned analysis of coupled mechanical systems. Computer Methods in Applied Mechanics and Engineering 2001, 190:3247-3270.
21. Felippa C., Park K., Farhat C. Partitioned Analysis of Coupled Mechanical Systems 1999, Center for Aerospace Structures, University of Colorado, 31.
22. Simo J.C., Miehe C. Associative coupled thermoplasticity at finite strains: formulation, numerical analysis and implementation. Computer Methods in Applied Mechanics and Engineering 1992, 98(1):41-104.
23. Armero F., Simo J.C. A new unconditionally stable fractional step method for nonlinear coupled thermomechanical problems. International Journal for Numerical Methods in Engineering 1992, 35:737-766.
24. Lewis R., Nithiarasu P., Seetharamu K. Fundamentals of the Finite Element Method for Heat Transfer and Fluid Flow 2004, John Wiley &Sons.
25. Hsu T.-R. The Finite Element Method in Thermomechanics 1986, Allen &Unwin.
26. Ziegler H. An Introduction to Thermomechanics. Series in Applied Mathematics and Mechanics 1983, North-Holland. 2nd edm.
27. Sluzalec A. Introduction to Nonlinear Thermomechanics 1991, Springer-Verlag.
28. Fung Y. Foundations of Solid Mechanics 1965, Prentice-Hall.
29. Boley B., Weiner J. Theory of Thermal Stresses 1960, John Wiley &Sons.
30. Carslaw H., Jaeger J. Conduction of Heat in Solids 1959, Clarendon Press. 2nd edn.
31. Huang H.-C., Usmani A. Finite Element Analysis for Heat Transfer 1994, Springer Verlag.
32. Bathe K.-J. Finite Element Procedures 1996, Prentice-Hall.
33. Cook R., Malkus D., Plesha M. Concepts and Applications of Finite Element Analysis 1989, John Wiley &Sons.
34. Belytschko T., Liu W.K., Moran B. Nonlinear Finite Elements for Continua and Structures 2000, John Wiley &Sons.
35. Belytschko T., Hughers T. Nonlinear Finite Element Analysis - A Short Course 2003, Paris.
36. Wang J. Prediction of welding deformations by FEM based on inherent strains 1998, San Diego, USA.
37. Ronda J., Oliver G.J. Consistent thermo-mechano-metallurgical model of welded steel with unified approach to derivation of phase evolution laws and transformation-induced plasticity. Computer Methods in Applied Mechanics and Engineering 2000, 189(2):361-418.
38. Armero F., Simo J.C. A priori stability estimates and unconditionally stable product formula algorithms for nonlinear coupled thermoplasticity. International Journal of Plasticity 1993, 9(6):749-782.
39. Karlsson L., Lindgren L.-E. Modeling of Casting, Welding and Advanced Solidification Processes V. Combined heat and stress-strain calculations. 1990, The Minerals, Metals &Materials Society, Davos, Switzerland.
40. Goldak J., Gu M., Hughes E. Steady state thermal analysis of welds with filler metal addition. Canadian Metallurgical Quarterly 1993, 32(1):49-55.
41. Balagangadhar D., et al. A displacement-based reference frame formulation for steady-state thermo-elasto-plastic material processes. International Journal of Solids and Structures 1999, 36(16):2397-2416.
42. Rajadhyaksha S., Michaleris P. Optimization of thermal processes using an Eulerian formulation and application in laser hardening. International Journal for Numerical Methods in Engineering 2000, 47:1807-1823.
43. Shanghvi J., Michaleris P. Thermo-elasto-plastic finite element analysis of quasi-state processes in Eulerian reference frames. International Journal for Numerical Methods in Engineering 2002, 53:1533-1556.
44. Paul S., Michaleris P., Shangvi J. Optimization of thermo-elasto-plastic processes using Eulerian sensitivity analysis. International Journal for Numerical Methods in Engineering 2003, 56:1125-1150.
45. Zhang L., Michaleris P. Investigation of Lagrangian and Eulerian finite element methods for modeling the laser forming process. Finite Elements in Analysis and Design 2004, 40:383-405.
46. Bergheau J., Pont D., Leblond J. Three-dimensional simulation of a laser surface treatment through steady state computation in the heat source's comoving frame 1992, Lulea,Sweden: Springer Verlag.
47. Gu M., et al. Modelling the evolution of microstructure in the heat affected zone of steady state welds. Canadian Metallurgical Quarterly 1993, 32:351-363.
48. Gu M., Goldak J. Steady-state formulation for stress and distortion of welds. ASME Journal of Engineering for Industry 1994, 116:467-474.
49. Goldak J., Gu M. Mathematical Modelling of Weld Phenomena 2. Computational weld mechanics of the steady state. 1995, The Institute of Materials.
50. Atteridge D. 3D Eulerian modeling of electroslag welding 1998, Pine Mountain, Georgia, USA.
51. Goldak J., Akhlagi M. Computational Welding Mechanics 2005, Springer.
52. Rosenthal D. Mathematical theory of heat distribution during welding and cutting. Welding Journal 1941, 20(5):220s-234s.
53. Rosenthal D. The theory of moving sources of heat and its application to metal treatments. Transactions of ASME Nov 1946, 68:849-866.
54. Codina R. Finite Element Formulation for the Numerical Solution of the Convection-Diffusion Equation 1993, CIMNE, Vol. 14.
55. Hughes T. Recent progress in the development and understanding of SUPG methods with a special reference to the compressible Euler and Navier-Stokes equations. International Journal for Numerical Methods in Fluids 1987, 7(1):1261-1275.
56. Onate E., Miquel J., Hauke G. Stabilized formulation for the advection-diffusion-absorption equation using finite calculus and linear finite elements. Computer Methods in Applied Mechanics and Engineering 2006, 195:3926-3946.
57. Levitas V., et al. Numerical modelling of martensitic growth in an elastoplastic material. Philosophical Magazine A 2002, 82(3):429-462.
58. Granjon H. Fundamentals of Welding Metallurgy 1991, Woodhead Publishing.
59. Easterling K. Introduction to the Physical Metallurgy of Welding 1983, Butterworths.
60. GrØNg Ø. Metallurgical Modelling of Welding 1994, The Institute of Materials.
61. Garcia De AndrÖS C., et al. Application of dilatometric analysis to the study of solid-solid phase transformation in steels. Materials Characterization 2002, 48:101-111.
62. Steel: A Handbook for Materials Research and Engineering. Volume 1: Fundamentals 1992, Verlag Stahleisen. W. JÄNiche (Ed.).
63. Fuglsang Andersen L. Residual Stresses and Deformations in Steel Structures 2000, Department of Naval Architecture and Offshore Engineering, Technical University of Denmark.
64. Leblond J., et al. Modeling in Welding, Hot Powder Forming, and Casting. Metallurgical and mechanical consequences of phase transformations in numerical simulations of welding processes 1997, 61-89. ASM International. L. Karlsson (Ed.).
65. BÖRjesson L., Lindgren L.-E. Thermal, metallurgical and mechanical models for simulation of multipass welding. ASME Journal of Engineering Materials and Technology Jan 2001, 123:106-111.
66. Satoh K. Transient thermal stresses of weld heat-affected zone by both-ends-fixed bar analogy. Transactions of the Japan Welding Society 1972, 3(1):125-134.
67. Okerblom N. The Calculation of Deformations of Welded Metal Structures. A Translation from the Russian by LC Ronson 1958, Her Majesty's Stationery Office.
68. Bhadeshia H. Cancellation of residual stress using transformation plasticity 2006, Seggau, Austria.
69. Vincent Y., Jullien J.-F., Gilles P. Thermo-mechanical consequences of phase transformations in the heat-affected zone using a cyclic uniaxial test. International Journal of Solids and Structures 2005, 42(14):4077-4098.
70. Pilipenko A. Computer Simulation of Residual Stress and Distortion of Thick Plates in Multielectrode Submerged Arc Welding - Their Mitigation Techniques 2001, Department of Machine Design and Materials Technology, Norwegian University of Science and Technology.
71. Jonsson M., Karlsson L., Lindgren L.-E. Numerical Methods in Heat Transfer. Deformations and stresses in butt-welding of large plates. 1985, 35-58. Wiley. R. Lewis (Ed.).
72. Berglund D., Alberg H. A two-stage approach for validation of welding- and heat treatment models in product development. Science and Technology of Welding and Joining 2005, 10(6):653-665.
73. Stone H., Roberts S., Reed R. A process model for the distortion induced by the electron-beam welding of a nickel-based superalloy. Metallurgical and Materials Transactions A Sep 2000, 31A:2261-2273.
74. Dhingra A.K., Murphy C.L. Numerical simulation of welding-induced distortion in thin-walled structures. Science and Technology of Welding and Joining 2005, 10(5):528-536.
75. Karlsson R., Josefson B. Three-dimensional finite element analysis of temperatures and stresses in a single-pass butt-welded pipe. ASME Journal of Pressure Vessel Technology 1990, 112:76-84.
76. Josefson L., Karlsson C. Transformation plasticity effects in residual stresses in a butt-welded pipe. ASME Journal of Pressure Vessel Technology 1992, 114:376-378.
77. Murthy Y.V.L.N., Rao G.V., Iyer P.K. Numerical simulation of welding and quenching processes using transient thermal and thermo-elasto-plastic formulations. Computers and Structures 1996, 60(1):131-154.
78. Troive L., Lindgren L.-E., Jonsson M. Thermal Stresses '95. Axial collapse load of a girth butt-welded pipe. 1995, Hamamatsu, Japan.
79. Comini G., et al. Finite element solution of non-linear heat conduction problems with special reference to phase change. International Journal for Numerical Methods in Engineering 1974, 8:613-624.
80. Chester M. Second sound in solids. Physical Review 1963, 131(5):2013-2015.
81. Ali Y., Zhang L. Relativistic heat conduction. International Journal of Heat and Mass Transfer 2005, 48(12):2397-2406.
82. Pham Q. Comparison of general purpose finite element methods for the Stefan problem. Numerical Heat Transfer Part B - Fundamentals 1995, 27(4):417-435.
83. Lewis R., et al. The Finite Element Method in Heat Transfer Analysis 1996, John Wiley &Sons.
84. Belytschko T. Computational Methods in Mechanics. An overview of semidiscretization and time procedures. 1983, 3-65. North-Holland. T. Belytschko, K.-J. Bathe (Eds.).
85. Hughes T. Computational Methods for Transient Analysis. Analysis of transient algorithms with particular reference to stability behavior 1983, 68-155. North-Holland. T. Belytschko, T. Hughes (Eds.).
86. Lindgren L.-E. Finite element modelling and simulation of welding, Part 1 Increased complexity. Journal of Thermal Stresses 2001, 24:141-192.
87. Bergman G., Oldenburg M. A finite element model for thermomechanical analysis of sheet metal forming. International Journal for Numerical Methods in Engineering 2004, 59(9):1167-1186.
88. Andersson B.A.B. Thermal stresses in a submerged-arc welded joint considering phase transformations. ASME Journal of Engineering Materials &Technology 1978, 100:356-362.
89. Karlsson L. Thermal Stresses. Thermal stresses in welding 1986, 300-389. Elsevier Science Publishers. R.B. Hetnarski (Ed.).
90. Rolph W.D., Bathe K.-J. An efficient algorithm for analysis of non linear heat transfer with phase changes. International Journal of Numerical Methods in Engineering 1982, 18:119-134.
91. Banaszek J. Comparison of control volume and Galerkin finite element methods for diffusion-type problems. Numerical Heat Transfer 1989, 16:59-78.
92. Crisfield M.A. Non-linear Finite Element Analysis of Solids and Structures, Volume 1: Essentials 1991, John Wiley &Sons.
93. Crisfield M.A. Non-Linear Finite Element Analysis of Solids and Structures, Vol. 2 Advanced Topics 1997, John Wiley &Sons.
94. Bonet J., Wood R.D. Nonlinear Continuum Mechanics for Finite Element Analysis 1997, Cambridge University Press.
95. Simo J.C., Hughes T.J.R. Computational Inelasticity 1997, Springer-Verlag. J.E. Marsden, L. Sirovich, S. Wiggins (Eds.).
96. Computational Methods for Transient Analysis. Computational Methods in Mechanics 1983, 1. North-Holland.
97. Malvern L.E. Introduction to the Mechanics of a Continuous Medium. Engineering of the Physical Sciences Series 1969, Prentice-Hall. J. Reswick, W. Rohsenow (Eds.).
98. Chung T. Applied Continuum Mechanics 1996, Cambridge University Press.
99. Simo J., Taylor R. Consistent tangent operators for rate-independent elastoplasticity. Computer Methods in Applied Mechanics and Engineering 1985, 48:101-118.
100. Ponthot J.P. Unified stress update algorithms for the numerical simulation of large deformation elasto-plastic and elasto-viscoplastic processes. International Journal of Plasticity 2002, 18(1):91-126.
101. Hughes T. Theoretical Foundation for Large Scale Computation of Nonlinear Material Behaviour. Numerical implementation of constitutive models: rate-independent deviatoric plasticity 1984, Northwestern University, Nijhoff, Evanston, Illinois.
102. Simo J., Pister K. Remarks on rate constitutive constitutive equations for finite deformation problems: computational implications. Computer Methods in Applied Mechanics and Engineering 1985, 46:201-215.
103. Arif A., Pervez T., Mughal M. Performance of a finite element procedure for hyperelastic-viscoplastic large deformation problems. Finite Elements in Analysis and Design 2000, 34:89-112.
104. Simo J.C. A framework for finite strain elastoplasticity based on maximum plastic dissipation and the multiplicative decomposition: Part I. Continuum formulation. Computer Methods in Applied Mechanics and Engineering 1988, 66:199-219.
105. Simo J.C. A framework for finite strain elastoplasticity based on maximum plastic dissipation and the multiplicative decomposition: Part II. Computational aspects. Computer Methods in Applied Mechanics and Engineering 1988, 68:1-31.
106. Hughes T., Winget J. Finite rotation effects in numerical integration of rate constitutive equations arising in large-deformation analysis. International Journal for Numerical Methods in Engineering 1980, 15(9):1862-1867.
107. Johnson G., Bammann D. A discussion of stress rates in finite deformation problems. International Journal of Solids and Structures 1984, 22(8):725-737.
108. SzabÓ L., Balla M. Comparison of some stress rates. International Journal of Solids and Structures 1989, 25(3):279-297.
109. Moss C. On instabilities in large deformation simple shear loading. Computer Methods in Applied Mechanics and Engineering 1984, 46:329-338.
110. Dienes J. On the analysis of rotation and stress rate in deforming bodies. Acta Mechanica 1979, 32:217-232.
111. Marin E., Mcdowell D. A semi-implicit integration scheme for rate-dependent and rate-independent plasticity. Computers and Structures 1997, 63(3):579-600.
112. Chaboche J.L., Cailletaud G. Integration methods for complex plastic constitutive equations. Computer Methods in Applied Mechanics and Engineering 1996, 133(1-2):125-155.
113. Saleeb A., Wilt T., Li W. Robust integration schemes for generalized viscoplasticity with internal-state variables. Computers and Structures 2000, 74:601-628.
114. Ramm E., Matzenmiller A. Consistent linearization in elasto-plastic shell analysis. Engineering Computations Dec 1988, 5:289-299.
115. Perzyna P., Pecherski R. Modified theory of viscoplasticity: physical foundations and identification of material functions for advanced strains. Archives of Mechanics 1983, 35(3):423-436.
116. Miller A.K. Unified Constitutive Equations for Creep and Plasticity. The MATMOD equations 1987, 139-219. Elsevier Applied Science Publishers. A.K. Miller (Ed.).
117. Kassner M.E., PÉRez-Prado M.-T. Five-power-law creep in single phase metals and alloys. Progress in Materials Science 2000, 45:1-102.
118. Frost H.J., Ashby M.F. Fundamental Aspects of Structural Alloy Design. Deformation-mechanism maps for pure iron, two austenitic stainless steels and a low-alloy ferritic steel 1977, 26-65. Plenum Press. R.I. Jaffee, B.A. Wilcox (Eds.).
119. Frost H.J., Ashby M.F. Deformation-mechanism Maps - The Plasticity and Creep of Metals and Ceramics 1982, Pergamon Press.
120. Unified Constitutive Equations for Creep and Plasticity 1987, Elsevier Applied Science Publishers Ltd. A.K. Miller (Ed.).
121. Raboin P. A Deformation-mechanism Material Model for Nike3D 1993, Lawrence Livermore National Laboratory.
122. De Souza Neto E. A simple robust numerical integration algorithm for a power-law visco-plastic model under both high and low rate-sensitivity. International Journal for Numerical Methods in Engineering 2004, 20:1-17.
123. Oddy A., Mcdill J., Goldak J. Consistent strain fields in 3D finite element analysis of welds. ASME Journal of Pressure Vessel Technology 1990, 112(3):309-311.
124. Mcdill J., Oddy A. A non-conforming eight to 26-node hexahedron for three-dimensional thermal-elastoplastic finite element analysis. Computers and Structures 1995, 54(2):183-189.
125. Friedman E. Thermomechanical analysis of the welding process using the finite element method. ASME Journal of Pressure Vessel Technology 1975, 97(3):206-213.
126. Friedman E. Numerical simulation of the gas tungsten-arc welding process 1977, Atlanta, USA.
127. Hibbitt H., Marcal P. A numerical thermo-mechanical model for the welding and subsequent loading of a fabricated structure. Computers and Structures 1973, 3:1145-1174.
128. Benzley S. A comparison of all hexagonal and all tetrahedral finite element meshes for elastic and elasto-plastic analysis 1995, Albuquerque, USA.
129. Cifuentes A., Kalbag A. A performance study of tetrahedral and hexahedral elements in 3-D finite element structural analysis. Finite Element in Analysis and Design 1992, 12:313-331.
130. Owen S. A survey of unstructured mesh generation technology 2006, cited 2006 4 Nov. http://www.andrew.cmu.edu/user/sowen/survey/index.html.
131. Owen S. Meshing software survey 2006, cited 2006 4 Nov. http://www.andrew.cmu.edu/user/sowen/softsurv.html.
132. Hyun S. Adaptive Remeshing and Simulating a Chain of Manufacturing Processes 2002, Department of Mechanical Engineering, Luleå University of Technology.
133. Mcdill J.M., et al. Isoparametric quadrilaterals and hexahedrons for mesh-grading algorithms. Communication in Applied Numerical Methods 1987, 3:155-163.
134. Mcdill J., Runnemalm K., Oddy A. An 8- to 16-node solid graded shell element for far-field applications in 3-D thermal-mechanical FEA. Mathematical Modelling and Scientific Computing 2001, 13(3):177-192.
135. Tan X., Vu-Quoc L. Efficient and accurate multilayer solid-shell element: non-linear materials at finite strain. International Journal for Numerical Methods in Engineering 2005, 63(15):2124-2170.
136. Lindgren L.-E., et al. Automatic remeshing for three-dimensional finite element simulation of welding. Computer Methods in Applied Mechanics and Engineering 1997, 147(3-4):401-409.
137. Stadthaus M., Michailov V., Wohlfahrt H. Mathematical Modelling of Weld Phenomena 6. Simulation of weld shape, microstructure, distortion and residual stresses for laser beam welding 2001, Institute of Materials, Minerals and Mining, Graz, Austria.
138. Lenz B., Rick F. MARC Benutzertreffen. Lösungsansatze zur Simulation des Laserstrahlschweissens mit thermomechanischen und mechanischen Analysen 1999, Munchen.
139. Runnemalm H., Hyun S. Three-dimensional welding analysis using an adaptive mesh scheme. Computer Methods in Applied Mechanics and Engineering 2000, 189:515-523.
140. Hemmer H., Klokkehaug S., Grong O. Mathematical Modelling of Weld Phenomena 6. Process modelling applied to electron beam welding of duplex stainless steels 2001, The Institute of Materials, Minerals and Mining, Graz, Austria.
141. Rieger A., Wriggers P. Adaptive methods for thermomechanical coupled contact problems. International Journal for Numerical Methods in Engineering 2004, 59:871-894.
142. Dow J. A Unified Approach to the Finite Element Method and Error Analysis Procedures 1999, Academic Press.
143. Barthold F.-J., Schmidt M., Stein E. Error indicators and mesh refinements for finite-element-computations of elastoplastic deformations. Computational Mechanics 1998, 22(3):225-238.
144. Zhu J.Z. A posteriori error estimation - the relationship between different procedures. Computer Methods in Applied Mechanics and Engineering 1997, 150:411f.
145. Zienkiewicz O.C., Zhu J.Z. A simple error estimator and adaptive procedure for practical engineering analysis. International Journal for Numerical Methods in Engineering 1987, 24:337-357.
146. Zienkiewicz O.C., Zhu J.Z. The superconvergent patch recovery and a posteriori error estimates, Part I: The recovery technique. International Journal for Numerical Methods in Engineering 1992, 33:1331-1364.
147. Zienkiewicz O.C., Boroomand B., Zhu J.Z. Recovery procedures in error estimation and adaptivity Part I: Adaptivity in linear problems. Computer Methods in Applied Mechanics and Engineering 1999, 176(1-4):111-125.
148. Lindgren L.-E., Hedblom E. Modelling of addition of filler material in large deformation analysis of multipass welding. Communications in Numerical Methods in Engineering 2001, 17(9):647-657.
149. Huerta A., et al. Adaptive finite element strategies based on error assessment. International Journal for Numerical Methods in Engineering 1999, 46:1803-1818.
150. Boroomand B., Zienkiewicz O.C. Recovery procedures in error estimation and adaptivity. Part II: Adaptivity in nonlinear problems of elasto-plasticity behaviour. Computer Methods in Applied Mechanics and Engineering 1999, 176(1-4):127-146.
151. Hyun S., Lindgren L.-E. Smoothing and adaptive remeshing schemes for graded element. Communications in Numerical Methods in Engineering 2001, 17:1-17.
152. Oddy A., et al. A distortion metric for iso-parametric finite elements. Canadian Society of Mechanical Engineers 1988, 12(4):213-217.
153. Andersen L.F. Residual Stresses and Deformations in Steel Structures 2000, Department of Naval Architecture and Offshore Engineering, Technical University of Denmark.
154. Souloumiac B., Boitout F., Bergheau J. Mathematical Modelling of Weld Phenomena 6. A new local-global approach for the modelling of welded steel component distortions 2001, Institute of Materials, Minerals and Mining, Graz, Austria.
155. Faure F., et al. Mathematical Modelling of Weld Phenomena 7. Prediction of distortions of large thins structures during welding using shell elements and multiscale approaches 2003, Graz, Austria.
156. Ueda Y. Modeling in Welding, Hot Powder Forming and Casting. Predicting and Measuring methods of two- and three-dimensional welding residual stresses by using inherent strain as a parameter 1997, 91-113. ASM International. L. Karlsson (Ed.).
157. Murakawa H., Luo Y., Ueda Y. Mathematical Modelling of Weld Phenomena 4. Inherent strain as an interface between computational welding mechanics and its industrial application 1998, Institute of Materials, Graz, Austria.
158. Ericsson M., Berglund D., Nylen P. Three dimensional simulation of robot path, heat transfer and residual stresses of a TIG-welded part with complex geometry 2002, Pine Mountain, Georgia: ASM International.
159. Iwaki T., Masubuchi K. Thermo-elasto-plastic analysis of orthotropic plate by the finite element method (in Japanese). Journal of the Society of Naval Architects of Japan 1971, 130:193-202.
160. Ueda Y., Yamakawa T. Thermal stress analysis of metals with temperature dependent mechanical properties 1971, Kyoto.
161. Ueda Y., Yamakawa T. Analysis of thermal elastic-plastic stress and strain during welding by finite element method. Transactions of the Japan Welding Research Institute 1971, 2(2):90-100.
162. Fujita Y., Nomoto T. Studies on thermal stresses in welding with special reference to weld cracking 1971, Tokyo.
163. Fujita Y., et al. Welding Stresses with Special Reference to Cracking 1972, International Institute of Welding.
164. Lindgren L.-E., Karlsson L. Deformations and stresses in welding of shell structures. International Journal for Numerical Methods in Engineering 1988, 2:155-164.
165. Mcdill J., et al. Finite element analysis of weld distortion in carbon and stainless steels. Journal of Strain Analysis 1990, 25(1):51-53.
166. Goldak J. Computational weld mechanics 1985, Oberammergau, Germany.
167. McDil J.M.J., Oddy A., Goldak J. Comparing 2-D plane strain and 3-D analyses of residual stresses in welds 1992, Gatlinburg, Tennessee.
168. Ma N.-X., et al. FEM analysis of 3-D welding residual stresses and angular distortion in T-type fillet welds. Transactions of the Japan Welding Institute 1995, 24(2):115-122.
169. Papazoglou V.J., Masubuchi K. Numerical analysis of thermal stresses during welding including phase transformation effects. ASME Journal of Pressure Vessel Technology 1982, 104:198-203.
170. Leung C., Pick R. Computer Modelling of Fabrication Processes and Constitutive Behaviour of Metals. The use of generalized plane strain elements in the prediction of residual stresses in welded flat plates 1986, Canada Centre for Mineral and Energy Technology, Ottawa.
171. Troive L. ., Finite element simulations of the bending of a flat plate to U-shaped beam cross-section and the welding to rectangular hollow cross-section and neutron diffraction determination of residual stresses 1989, Gatlinburg, USA.
172. Mok D., Pick R. Finite element study of residual stresses in a plate T-joint fatigue specimen. Journal of Mechanical and Engineering Science 1990, 204(C2):127-134.
173. Wikander L., et al. Finite element simulation and measurement of welding residual stresses. Modelling and Simulation in Materials Science and Engineering 1994, 2(4):845-864.
174. Roelens J. Mathematical Modelling of Weld Phenomena 2. Determination of residual stresses in submerged arc multi-pass welds by means of numerical simulation and comparisons with experimental measurements 1995, The Institute of Materials, Graz, Austria.
175. Michaleris P., Sun X. Finite element analysis of thermal tensioning techniques mitigating weld buckling distortion. Welding Journal 1997, 76(11):451s-457s.
176. Michaleris P., Feng Z., Campbell G. Evaluation of 2D and 3D FEA models for predicting residual stress and distortion. Approximate Methods in the Design and Analysis of Pressure Vessels and Piping Components 1997, 347:91-102. American Society of Mechanical Engineers, Pressure Vessels and Piping Division (Publication) PVP.
177. Ferro P., et al. The influence of phase transformations on residual stresses induced by the welding process - 3D and 2D numerical models. Modelling and Simulation in Materials Science and Engineering 2006, 14:117-136.
178. Runnemalm H., Berglund D. Finite element simulation of welding prediction of deformation patterns 2000, Bokenas, Sweden.
179. Dye D., et al. Modeling of the mechanical effects induced by the tungsten-inertgas welding of the In718 superalloy. Metallurgical and Materials Transactions A July 2001, 32A:1713-1725.
180. Ravichandran G., et al. Prediction of axis shift distortion during circumferential welding of thin pipes using the finite element method. Welding Journal January 1997, 39s-55s.
181. Zhang J., et al. Modeling of weld residual stresses in core shroud structures. Nuclear Engineering and Design 2000, 195(2):171-187.
182. Dong Y., et al. Finite element modeling of residual stresses in austenitic stainless steel pipe girth welds. Welding Journal 1997, 76(10):442s-449s.
183. Fricke S., Keim E., Schmidt J. Fracture mechanics investigation of root formation and shrinkage during welding 1998, ASME, San Diego, USA.
184. Fricke S., Keim E., Schmidt J. Mathematical Modelling of Weld Phenomena 4. Modelling of root formation during the welding process with the help of the 3D FE method 1998, The Institute of Materials, Graz, Austria.
185. Fricke S., Keim E., Schmidt J. Numerical weld modeling - a method for calculating weld-induced residual stresses. Nuclear Engineering and Design 2001, 206(2-3):139-150.
186. Dike J. Finite element modeling and validation of residual stresses in 304L girth welds 1998, ASM International, Pine Mountain, USA.
187. Chakravarti A., Mali L., Goldak J. Prediction of distortion and residual stresses in panel welds 1986, Ottawa, Canada.
188. Tsai C., Park S., Cheng W. Welding distortion of a thin-plate panel structure. Welding Journal May 1999, 156s-165s.
189. Michaleris P., Debiccari A. Prediction of welding distortion. Welding Journal 1997, 76(4):172s-181s.
190. Dong P., Zhang J., Li M. Computational modeling of weld residual stresses and distortions - an integrated framework and industrial applications 1998, ASME Press. Vess. & Piping Division.
191. Rybicki E. A finite element model for residual stresses in girth-butt welded pipes 1977.
192. Rybicki E.F., et al. A finite-element model for residual stresses and deflections in girth-butt welded pipes. ASME Journal of Pressure Vessel Technology 1978, 100:256-262.
193. Rybicki E.F., Stonesifer R.B. Computation of residual stresses due to multipass welds in piping systems. ASME Journal of Pressure Vessel Technology May 1979, 101:149-154.
194. Ueda Y., Nakacho K. Simplifying methods for analysis of transient and residual stresses and deformations due to multipass welding. Transactions of Japan Welding Institute 1982, 11(1):95-103.
195. Leung C., Pick R., Mok D. Finite element analysis of multipass welds. WRC Bulletin Aug 1990, 356:11-33.
196. Hong J., Tsai C., Dong P. Assessment of numerical procedures for residual stress analysis of multipass welds. Welding Journal 1998, 77(9):372s-382s.
197. Li M. A 3D finite element analysis of temperature and stress fields in girth welded 304L stainless steel pipe 1995, ASM International, Gatlinburg, USA.
198. Li M. An experimental analysis of temperature and stress fields in girthwelded 304L stainless steel pipes 1995, ASM International, Gatlinburg, USA.
199. Ortega A. Analysis and validation of multi-pass girth welds in pipes 1998, The Minerals, Metals & Materials Society, San Diego, USA.
200. Dike J. Finite element modeling of multipass GMA welds in steel plates 1995, ASM International, Gatlinburg, USA.
201. Chakravarti A. Prediction of distortion in overlayed repair welds 1987, Montreal, Canada.
202. Hinrichsen B. Prediction of welding induced distortion in thin-walled ship panels. Ship Technology Research 1999, 46:153-163.
203. Huang T., et al. Fabrication and engineering technology for lightweight ship structures, Part 1: distortion and residual stresses in panel fabrication. Journal of Ship Production 2004, 20:43-59.
204. Ueda Y., Yuan M. Prediction of residual stresses in butt-welded plates using inherent strain. ASME Journal of Engineering Materials and Technology Oct 1993, 115:417-423.
205. SchimmÖLler H. Bestimmung von Eigenspannungen in ebenen plattierten Werkstoffen, Teil 1: Rechnerische Grundlagen. Materialprufung 1972, 14(4):115-122.
206. SchimmÖLler H. Bestimmung von Eigenspannungen in ebenen plattierten Werkstoffen, Teil 2: Eigenspannungen in warmgewalzten und sprenggeschweissten austenit-plattierten Stahlblechen. Materialprufung 1972, 14(11):380-387.
207. Yuan M., Ueda Y. Prediction of residual stresses in welded T- and I-joints using inherent strains. ASME Journal of Engineering Materials and Technology 1996, 118:229-234.
208. Jung G., Tsai C. Plasticity-based distortion analysis for fillet welded thin-plate T-joints. Welding Journal June 2004, 177s-187s.
209. Lindgren L.-E. Finite element modelling and simulation of welding, Part 3 Efficiency and integration. Journal of Thermal Stresses 2001, 24:305-334.
210. Oberkampf W.L., Trucano T.G. Verification and validation in computational fluid dynamics. Progress in Aerospace Sciences 2002, 38(3):209-272.
211. Oberkampf W.L., Trucano T.G., Hirsch C. Verification, validation, and predictive capability in computational engineering and physics. Applied Mechanics Reviews 2004, 57(5):345-384.
212. Oberkampf W.L., et al. Error and uncertainty in modeling and simulation. Reliability Engineering and System Safety 2002, 75(3):333-357.
213. Oberkampf W.L., et al. Challenge problems: uncertainty in system response given uncertain parameters. Reliability Engineering and System Safety 2004, 85(1-3):11-19.
214. Meng X.N., Laursen T.A. Energy consistent algorithms for dynamic finite deformation plasticity. Computer Methods in Applied Mechanics and Engineering 2002, 191(15-16):1639-1675.
215. Sudnik W., Radaj D., Erofeew W. Mathematical Modelling of Weld Phenomena 4. Validation of computerised simulation of welding processes 1998, The Institute of Materials, Minerals and Mining, Seggau, Graz.
216. Alberg H. Simulation of Welding and Heat Treatment. Modelling and Validation 2005, Department of Applied Physics and Mechanical Engineering, Luleå University of Technology.
217. Belytschko T., Mish K. Computability in non-linear solid mechanics. International Journal of Numerical Methods of Engineering 2001, 52:3-21.
218. Trucano T.G., et al. Calibration, validation, and sensitivity analysis: What's what. Reliability Engineering and System Safety 2006, 91(10-11):1331-1357.
219. Radaj D., Lindgren L.-E. Mathematical Modelling of Weld Phenomena 8. Verification and validation in computational welding mechanics 2006, The Institute of Materials, Minerals and Mining, Seggau, Graz.
220. Kajberg J., et al. High strain-rate tensile testing and viscoplastic parameter identification using microscopic high-speed photography. International Journal of Plasticity 2004, 20(4-5):561-575.
221. Garcia De AndrÉS C., et al. Modelling of kinetics and dilatometric behaviour of non-isothermal pearlite-to-austenite transformation in an euctectoid steel. Scripta Materialia 1998, 39(6):791-796.
222. Cavallo N. Thermomechanical behaviour of a carbon manganese steel under martensitic transformation 1997, Linkoping University, Linkoping, Sweden.
223. Taleb L., Cavallo N., Waeckel F. Experimental analysis of transformation plasticity. International Journal of Plasticity 2001, 17(1):1-20.
224. Taleb L., Cavallo N., Waeckel F. Erratum to 'Experimental analysis of transformation plasticity. [International Journal of Plasticity 2001, 17:1-20. ]. International Journal of Plasticity, 2001. 17(7): 1029.
225. Otsuka T., Wakasu Y., Inoue T. A simple identification of transformation plastic behaviour and some data for heat treating materials. International Journal of Materials and Product Technology 2005, 24(1-4):298-311.
226. Alberg H., Berglund D. Comparison of plastic, viscoplastic, and creep models when modelling welding and stress relief heat treatment. Computer Methods in Applied Mechanics and Engineering 2003, 192(49-50):5189-5208.
227. LundbÄCk A., Alberg H., Henriksson P. Mathematical Modelling of Weld Phenomena 7. Simulation and validation of TIG-welding and post weld heat treatment of an Inconel 718 plate 2003, The Institute of Materials, Graz, Austria.
228. Sudnik W., Radaj D., Erofeew W. Computer simulation of laser beam welding, modelling and verification. Journal of Physics D: Applied Physics 1996, 29:2811-2817.
229. Ortega A. Thermomechanical modeling of a stationary gas metal arc weld: a comparison between numerical and experimental results 1992, ASM International, Gatlinburg, USA.
230. Wikman B. Inverse Modelling for Determination of Constitutive Parameters 1999, Department of Mechanical Engineering, Luleå, 47.
231. Bruhns O.T., Anding D.K. On the simultaneous estimation of model parameters used in constitutive laws for inelastic material behaviour. International Journal of Plasticity 1999, 15(12):1311-1340.
232. Lindgren L.E., Alberg H., Domkin K. Constitutive modelling and parameter optimisation 2003, Barcelona.
233. Mahnken R., Stein E. Parameter identification for viscoplastic models based on analytical derivatives of a least-squares functional and stability investigation. International Journal of Plasticity 1996, 12(4):451-479.
234. Zentar R., Hicher P., Moulin G. Identification of soil parameters by inverse analysis. Computer and Geotechnics 2001, 28:129-144.
235. Saleb A., et al. A general hereditary multimechanism-based deformation model with application to the viscoelastoplastic response of titanium alloys. International Journal of Plasticity 2001, 17:1305-1350.
236. Mahnken R., Stein E. The identification of parameters for visco-plastic models via finite-element methods and gradient methods. Modelling and Simulations in Materials Science Engineering 1994, 2:597-616.
237. Eriksson M., Wikman B., Bergman G. Estimation of material parameters at elevated temperatures by inverse modelling of a gleeble experiment. Modelling and Simulations in Materials Science Engineering 2002, 10:277-284.
238. Mahnken R., Stein E. A unified approach for parameter identification of inelastic material models in the frame of the finite element method. Computer Methods in Applied Mechanics and Engineering 1996, 136:225-258.
239. Mahnken R., Kuhl E. Parameter identification of gradient enhanced damage models with the finite element method. European Journal of Mechanics A Solids 1999, 18:819-835.
240. Fletcher R. Practical Methods of Optimization, Vol. 1 Unconstrained Optimization 1980, John Wiley &Sons.
241. Fletcher R. Practical Methods of Optimization, Vol. 2 Constrained Optimization 1981, John Wiley &Sons.
242. Gen M., Cheng R. Genetic Algorithms &Engineering Optimzation. Wiley Series in Engineering Design and Automation 2000, John Wiley &Sons. H. Parsaei (Ed.).
243. Muller D., Hartmann G. Identification of materials parameters for inelastic constitutive models using principles of biologic evolution. ASME Journal of Engineering Materials and Technology 1989, 111(3):299-305.
244. Furukawa T., et al. An automated system for simulation and parameter identification of inelastic constitutive models. Computer Methods in Applied Mechanics and Engineering 2002, 191:2235-2260.
245. Huber N., Tsakmakis C. A neural network tool for identifying the material parameters of a finite deformation viscoplasticity model with static recovery. Computer Methods in Applied Mechanics and Engineering 2001, 191:353-384.
246. Berglund D. Validation of Models for Welding and Post Weld Heat Treatment in Product Development of Aerospace Components 2003, Department of Applied Physics and Mechanical Engineering, Luleå University of Technology.
247. Stouffer D.C., Dame L.T. Inelastic Deformations of Metals - Models, Mechanical Properties and Metallurgy 1996, John Wiley &Sons.
248. Fischer F.D., et al. Transformation induced plasticity revised and updated formulations. International Journal of Solids and Structures 1998, 35(18):2209-2227.
249. Bell J., Truesdell C. The Experimental Foundation of Solid Mechanics. Mechanics of Solids Series 1984, I. Springer-Verlag.
250. Bodner S., Miele A. Unified Plasticity for Engineering Applications. Mathematical Concepts and Methods in Science and Engineering Series 2002, 47. Kluwer Academic/Plenum Publishers.
251. Properties and Selection: Irons, Steels and High-performance Alloys. Metals Handbook 1990, ASM International, Vol. 1. 10th. ASM International Handbook Committee (Ed.).
252. Stainless Steels, ASM Specialty Handbook 1994, ASM International, ASM International Handbook Committee, ed. J. Davis (Ed.).
253. Steel A Handbook for Materials Research and Engineering. Volume 2: Applications 1992, Verlag Stahleisen. W. JÄNiche (Ed.).
254. Richter F. Die wichtigsten physikalischen Eigenschaften von 52 Eisenwerkstoffen 1973, Verlag Stahleisen.
255. Hepworth J. Finite element calculation of residual stresses in welds 1980, Swansea, UK.
256. Ueda Y., et al. Mathematical treatment of phase transformation and analytical calculation of restraint stress-strain. Transactions of Japan Welding Institute 1985, 14(1):153-162.
257. Free J., Porter Goff R. Predicting residual stresses in multi-pass weldments with the finite element method. Computers and Structures 1989, 32(2):365-378.
258. Tekriwal P., Mazumder J. Transient and residual thermal strain-stress analysis of GMAW. ASME Journal of Engineering Materials and Technology 1991, 113:336-343.
259. Ueda Y., Nakacho K., Shimuzu T. Improvement of residual stresses of circumferential joint of pipe by heat-sink welding. ASME Journal of Pressure Vessel Technology 1986, 108(2):14-23.
260. Brown S., Song H. Finite element simulation of welding of large structures. Journal of Engineering for Industry 1992, 114:441-451.
261. Brown S., Song H. Implications of three-dimensional numerical simulations of welding of large structures. Welding Journal February 1992, 55s-62s.
262. Nickell R., Hibbitt H. Thermal and mechanical analysis of welded structures. Nuclear Engineering and Design 1975, 32:110-120.
263. Ueda Y. Finite element modeling and residual stress calculation for multi-pass single welded joint between a plate and the penetrating pipe 1991, The Minerals, Metals & Materials Society, Davos, Austria.
264. Shim Y., et al. Determination of residual stress in thick-section weldments. Welding Journal 1992, 71:305s-312s.
265. Michaleris P., et al. Fatigue and Fracture Mechanics. Incorporation of residual stress effects into fracture mechanics assessments via the finite element method 1996, ASTM, Saratoga Springs, USA.
266. Ueda Y., et al. Transient and residual stresses from multipass welding in very thick plates and their reduction from stress relief annealing. Transactions of Japan Welding Research Institute 1976, 5:179-187.
267. Ueda Y. Transient and residual stresses from multipass welding in very thick plates and their reduction from stress relief annealing 1977, Tokyo.
268. Josefson B. Residual stresses and their redistribution during annealing of a girth-butt welded thin-walled pipe. ASME Journal of Pressure Vessel Technology 1982, 104:245-250.
269. Inoue T., Wang Z. High temperature behaviour of steels with phase transformation and the simulation of quenching and welding processes 1983, Stockholm, Sweden.
270. Wang Z., Inoue T. Viscoplastic constitutive relation incorporating phase transformation - application to welding. Material Science and Technology 1985, 1:899-903. Oct.
271. Wang Z., Inoue T. Viscoplastic constitutive relation incorporating phase transformation - application to welding. Material Science and Technology Oct 1985, 1:899-903.
272. Bergheau J., Leblond J. Coupling between heat flow, metallurgy and stress-strain computations in steels: the approach developed in the computer code Sysweld for welding or quenching 1991, The Minerals, Metals & Materials Society, Davos, Austria.
273. Devaux J., Pont D., Leblond J. Numerical simulation of the repair of a defect-containing zone by a manual welding procedure 1991, Stavanger, Norway.
274. Inoue T. Metallo-thermo-mechanics. Transactions of Japan Welding Research Institute 1996, 25(2):69-87.
275. Mathematical Modelling of Weld Phenomena 4. Residual stresses and distortion metallo-thermo-mechanics simulation of engineering processes incorporating phase transformation 1998, 547-575. Institute of Materials, H. Cerjak, and H. Bhadeshia, Editors. T. Inoue (Ed.).
276. Roelens J.-B., Maltrud F., Lu J. Determination of residual stresses in submerged arc multi-pass welds by means of numerical simulation and comparison with experimental measurements. Welding in the World 1994, 33(3):152-159.
277. Roelens J.-B. Numerical simulation of multipass submerged arc welding - determination of residual stresses and comparison with experimental measurements. Welding in the World 1995, 35(2):110-117.
278. BÖRjesson L. Mechanical Engineering. Coupled thermal, metallurgical and mechanical models of multipass welding 1999, Luleå University of Technology.
279. Myhr O.R., GrØNg O. Modelling of non-isothermal transformations in alloys containing a particle distribution. Acta Materialia 2000, 48(7):1605-1615.
280. Myhr O.R., GrØNg O., Andersen S.J. Modelling of the age hardening behaviour of Al-Mg-Si alloys. Acta Materialia 2001, 49(1):65-75.
281. Dufrene L., Truc J., Martin R. Modeling of thermal stresses during an electron-beam welding process. Journal of Thermal Stresses 1996, 19(3):211-238.
282. SjÖStrÖM S. The Calculation of Quench Stresses in Steel 1982, University of Linköping.
283. Perlade A., Bouaziz O., Furnemont Q. A physically based model for TRIP-aided carbon steels behaviour. Materials Science and Engineering A 2003, 356:145-152.
284. Gladman T., Mcivor I.D., Pickering F. Some aspects of the structure-property relationships in high-carbon ferrite-pearlite steels. Journal of Iron and Steel Institute 1972, 210:916-930.
285. Bouquerel J., Verbeken K., De Cooman B.C. Microstructure-based model for the static mechanical behaviour of multiphase steels. Acta Materialia 2006, 54(6):1443-1456.
286. Leblond J., Mottet G., Devaux J. A theoretical and numerical approach to the plastic behavior of steels during phase transformations - II. Study of classical plasticity for ideal-plastic phases. Journal of the Mechanics and Physics of Solids 1986, 34(4):411-432.
287. Bouaziz O., Buessler P. Iso-work increment assumption for heterogeneous material behaviour modelling. Advanced Engineering Materials 2004, 6(1-2):79-83.
288. Brickstad B., Josefson B. A parametric study of residual stresses in multi-pass butt-welded stainless steel pipes. International Journal of Pressure Vessels and Piping 1998, 75:11-25.
289. Mahin K., et al. Prediction and measurements o residual elastic strain distributions in gas tungsten arc welds. Welding Journal 1991, 70(9):245s-260s.
290. Mahin K., et al. Modeling of Casting and Welding Processes IV. Evaluation of residual stress distribution in a traveling GTA weld using finite element and experimental techniques 1988, The Minerals, Metals &Materials Society, Sheraton Palm Coast, Florida, USA.
291. Brust F., Dong P., Zhang J. Advances in Computational Engineering Science. A constitutive model for welding process simulation using finite element methods 1997, Tech Science Press, Anaheim, CA.
292. Lindgren L.-E. Finite element modelling and simulation of welding, Part 2 Improved material modelling. Journal of Thermal Stresses 2001, 24:195-231.
293. Moore J., Bibby M., Goldak J. Welding Research: The State of the Art. A comparison of the point source and finite element schemes for computing weld cooling 1985, ASM, Toronto, Canada.
294. Pehlke R., Jeyarajan A., Wada H. Summary of Thermal Properties for Casting Alloys and Mold Materials 1982, University of Michigan.
295. Dubois D., Devaux J., Leblond J.B. Numerical simulation of a welding operation: Calculation of residual stresses and hydrogen diffusion 1984, San Francisco.
296. Ashby M. Physical modelling of material problems. Materials Science and Technology Feb 1992, 8:102-111.
297. Bru D., et al. Mathematical Modelling of Weld Phenomena 3. Influence of material properties at high temperatures on the modelling of welding residual stress and deformation state 1997, The Institute of Materials, Graz, Austria.
298. Sekhar N. Characterisation of distortion during the laser welding of wasp-alloy: modelling and in-situ process monitoring 1998, ASM International, Pine Mountain, USA.
299. Suzuki H., et al. Studies on the Flow Stress of Metals and Alloys 1968, The Institute of Industrial Science, University of Tokyo.
300. Argyris J.H., Szimmat J., Willam K.J. Computational aspects of welding stress analysis. Computer Methods in Applied Mechanics and Engineering 1982, 33:653-666.
301. Argyris J., Szimmat J., Willam K. Numerical Methods in Heat Transfer. Finite element analysis of arc-welding processes 1985, 35-58. Wiley. R. Lewis (Ed.).
302. Chidiac S., Mirza F. Thermal stress analysis due to welding processes by the finite element method. Computers and Structures 1993, 46(3):407-412.
303. Myhr O., et al. Modeling of microstructure evolution, residual stresses in processing and distortions in 6082-T6 aluminium weldments. Welding Journal 1998, 77(7):286s-292s.
304. Myhr O. Modeling of microstructure evolution and residual stresses in processing and welding of 6082 and 7108 aluminium alloys 1998, Pine Mountain, Georgia, USA.
305. Goldak J., et al. Thermal stress analysis of welds: From melting point to room temperature. Transactions of Japan Welding Research Institute 1996, 25(2):185-189.
306. Goldak J., et al. Mathematical Modelling of Weld Phenomena 3. Thermal stress analysis in solids near the liquid region in welds 1997, The Institute of Materials, Graz, Austria.
307. Winters W., Mahin K. PASTA2D Modeling of an axisymmetric stationary gas tungsten arc weld 1991, The Minerals, Metals & Materials Society, Davos, Austria.
308. Bammann D.J. Modeling temperature and strain rate dependent large deformations of metals. Applied Mechanics Review 1990, 43(5):312-319.
309. Bammann D.J., Chiesa M.L., Johnson G.C. 19th International Congress on Theoretical and Applied Mechanics. Modeling large deformation and failure in manufacturing processes 1996, Elsevier Science, Kyoto.
310. Chen Y., Sheng I. Residual stress in weldment. Journal of Thermal Stresses 1992, 15(1):53-69.
311. Bammann D.J., Ortega A.R. Modeling of Casting, Welding and Advanced Solidification Processes VI. The influence of the Bauschinger effect and yield definition on the modeling of welding processes 1993, The Minerals, Metals &Materials Society, Warrendale.
312. Murthy Y., Rao G.Venkata, Iyer P.Krishna Analysis of residual stresses in hemispherical head to cylindrical shell joints of steam generator by weld cycle simulation. Journal of Materials Processing Technology 1994, 44(3-4):273-280.
313. Fischer F.D., Resiner G., Werner E., Tanaka K., Cailletaud G., Antretter T. A new view on transformation induced plasticity (TRIP). International Journal of Plasticity 2000, 16(7-8):723-748.
314. Greenwood G., Johnson R. The deformation of metals under small stresses during phase transformation. Proceddings of the Royal Society 1965, 283:403-422.
315. Magee C., Davies R. On the volume expansion accompanying the fcc to bcc transformation in ferrous alloys. ACTA Metallurgica 1972, 20:1031-1043.
316. Oddy A., Goldak J., McDill M. Transformation effects in the 3D finite element analysis of welds 1989, Gatlinburg, USA.
317. Sjostrom S. Interactions and constitutive models for the quench stresses in steel 1984, Linkoping, Sweden.
318. SjÖStrÖM S. Interactions and constitutive models for calculating quench stresses in steel. Materials Science and Technology Oct 1985, 1:823-829.
319. Vincent Y., Bergheau J.-M., Leblond J.-B. Viscoplastic behaviour of steels during phase transformations. Comptes Rendus Mecanique 2003, 331:587-594.
320. Taleb L., Petit S. New investigations on transformation induced plasticity and its interaction with classical plasticity. International Journal of Plasticity 2006, 22(1):10-130.
321. Oddy A., Goldak J., Reed R. Martensite formation, transformation plasticity and stress in high strength steel welds 1992, ASM International, Gatlinburg, USA.
322. Antretter T. Theory, experiments and numerical modelling of phase transformations with emphasis on TRIP 2006, Ghent: Wissenschaftsverlag Mainz GmbH.
323. Koistinen D., Marburger R. A general equation prescribing the extent of the austenite-martensite transformation in pure-carbon alloys amd plain carbon steels. Acta Metallica 1959, 7:59-60.
324. Leblond J., Mottet G., Devaux J. A theoretical and numerical approach to the plastic behavior of steels during phase transformations - I. Derivation of general relations. Journal of the Mechanics and Physics of Solids 1985, 34(4):395-409.
325. Leblond J.B., Devaux J., Devaux J.C. Mathematical modelling of transformation plasticity in steels I: Case of ideal-plastic phases. International Journal of Plasticity 1989, 5:551-572.
326. Leblond J.B. Mathematical modelling of transformation plasticity in steels II: Coupling with strain hardening phenomena. International Journal of Plasticity 1989, 5:573-591.
327. Leblond J., et al. Modeling in Welding, Hot Powder Forming, and Casting. Metallurgical and mechanical consequences of phase transformations in numerical simulations of welding processes 1997, 61-89. ASM International. L. Karlsson (Ed.).
328. Devaux J. Comportement plastique des aciers en cours de transformations de phases. Etude numérique des lois de mélange et de la plasticité de transformation 1998, SYSTUS International.
329. Leblond J., et al. IUTAM Symposium on Thermomechanical Couplings in Solids. Plastic behaviour of steels during phase transformations 1987, Elsevier Science Publisher BV.
330. Leblond J., Devaux J. Interactions between transformation plasticity and strain hardening phenomena in steels 1988, Nancy, France.
331. Mitter W. Materialkundlich-Technische Reihe 7. Umwandlungsplastizität und ihre Berucksichtung bei der Berechnung von Eigenspannungen 1987, Bornträger-Verlag.
332. Mechanics of Solids with Phase Changes. CISM International Centre for Mechanical Sciences 1997, Springe, Vol. 368. M. Berveiller, F. Fischer (Eds.).
333. Thiessen R.G., Richardson I.M., Sietsma J. Physically based modelling of phase transformations during welding of low-carbon steel. Materials Science and Engineering: A 2006, 427(1-2):223-231.
334. International A. One-Minute-Mentor 2006, http://www.asminternational.org/Content/NavigationMenu/Magazines/HeatTransferProgress/One_Minute_Mentor1/One_Minute_Mentor.htm.
335. International A. One-Minute-Mentor 2006, http://www.asminternational.org/Content/NavigationMenu/Magazines/HeatTransferProgress/One_Minute_Mentor1/One_Minute_Mentor.htm.
336. Leblond J.B., Devaux J. A new kinetic model for anisothermal metallurgical transformations in steels including effect of austenite grain size. Acta Metallurgica 1984, 32(1):137-146.
337. Leblond J.-B., et al. Mathematical models of anisothermal phase transformations in steels, and predicted plastic behaviour. Materials Science and Technology October 1985, 1:815-822.
338. Johnson W., Mehl R. Reaction kinetics in processes of nucleation and growth. Transactions of American Institute of Mining and Metallurgical Engineers 1939, 135:416-458.
339. Avrami M. Kinetics of phase change. III: Granulation, phase change and microstructures. Journal of Chemical Physics 1941, 9:177-184.
340. Kolmogorov A. Statistical theory of crystallization of metals (in Russian). Izvestia Akademia Nauk SSSR Ser. Mathematica 1937, 1(1):355-359.
341. Porter D., Easterling K. Phase Transformations in Metals and Alloys 1992, Chapman &Hall. 2nd edn.
342. Kang S.-H., Im Y.-T. Three-dimensional finite-element analysis of the quenching process of plain-carbon steel with phase transformation. Metallurgical and Materials Transactions 2005, 36A(9):2315.
343. Fernandes F., Denis S., Simon A. Mathematical model coupling phase transformation and temperature evolution during quenching of steels. Materials Science and Technology Oct 1985, 1:838-844.
344. Hildenwall B. Linköping Studies in Science and Technology. Prediction of the residual stresses created during quenching 1979, Linköping University.
345. Kirkaldy J.S., Venugopalan D. Prediction of microstructure and hardenabilityin low alloy steels 1983, Philadelphia.
346. Kirkaldy J.S., Venugopalan D. Phase transformations in ferrous alloys 1984, 125-148.
347. Kirkaldy J.S., Sharma R.C. A new phenomenology for steel IT and CCT curves. Scripta Metallurgica 1982, 16:1193-1198.
348. Watt D., et al. An algorithm for modelling microstructural development in weld heat-affected zones (Part A) Reaction kinetics. Acta Metallurgica 1988, 36(11):3029-3035.
349. Henwood C., et al. Coupled transient heat transfer - microstructure weld computations (Part B). Acta Metallurgica 1988, 36(1):3037-3046.
350. Oddy A.S., Mcdill J.M.J., Karlsson L. Microstructural predictions including arbitrary thermal histories, reaustenization and carbon segregation effects. Canadian Metallurgical Quarterly 1996, 35(3):275-283.
351. Pickering F. Physical metallurgical development of stainless steels. In Stainless Steels 1984, 84. Gothenburg, Sweden.
352. Easterling K., Ashby M., Li A. A first report for grain growth in welds. Acta Metallurgica 1982, 30:1969-1978.
353. Svensson L.-E. Control of Microstructures and Properties in Steel Arc Welds. Materials Science and Technology Series 1994, CRC Press. B. Ralph (Ed.).
354. Evans G., Bailey N. Metallurgy of Basic Weld Metal 1997, Woodhead Publishing.
355. Olson G., Cohen M. Stress-assisted isothermal martensitic transformation; application to TRIP steels. Metallurgical Transactions Nov 1982, 13A:1907-1914.
356. Tsakiris V., Edmonds D.V. Martensite and deformation twinning in austenitic steels. Materials Science and Engineering A 1999, 273-275:430-436.
357. Ganesh Sundara Raman S., Padmanabhan K. Tensile deformation-induced martensitic transformation in AISI 304LN austenitici stainless steel. Journal of Materials Science Letters 1994, 13(5):389-392.
358. Reed-Hill R.E., Abbaschian R. Physical Metallurgy Principles 1992, PWS-KENT Publishing Company. 3rd edn.
359. Fischer F. A micromechanical model for transformation plasticity in steels. Acta Metallurgical et Materialia 1990, 38(8):1535-1546.
360. Tanaka K., Sato Y. A mechanical view of transformation plasticity. Ingeniur-Archiv 1985, 55:147-155.
361. Inoue T., Wang Z. Numerical Methods in Industrial Forming Processes. Finite element analysis of coupled thermo-inelastic problem with phase transformation 1982, 391-400. Pineridge Press, Swansea. J. Wood, H. David, J. Alexander (Eds.).
362. Inoue T., Wang Z. Coupling between stress, temperature, and metallic structures during processes involving phase transformations. Materials Science Technology 1985, 1:845-850.
363. Denis S., et al. Stress-phase-transformation interactions - basic principles, and calculation of internal stresses. Materials Science and Technology Oct 1985, 1:805-814.
364. Kharkin V., et al. Mathematical Modelling of Weld Phenomena 7. Effects of latent heat of fusion on thermal processes during welding 2003, Seggau, Austria: Teschnische Universität Graz.
365. Feng Z. A computational analysis of thermal and mechanical conditions for weld solidification cracking. Welding in the World 1994, 33(5):340-347.
366. Feng Z., Zacharia T., David S. Mathematical Modelling of Weld Phenomena 3. On the thermomechanical conditions for weld metal solidification cracking 1997, Graz, Austria: The Institute of Materials.
367. Dike J., Brooks J., Krafcik J. Finite element modeling and verification ofthermal-mechanical behavior in the weld pool region 1995, ASM International, Gatlinburg, USA.
368. Madhusudana C., Fletcher L. Contact heat transfer - the last decade. AIAA Journal 1985, 24(3):510-523.
369. Salgon J., et al. A mechanical and geometrical approach to thermal contact resistance. International Journal of Heat Mass Transfer 1997, 40(5):1121-1129.
370. Malinowski Z., Lenard J., Davies M. A study of the heat-transfer coefficient as a function of temperature and pressure. Journal of Materials Processing 1994, 41:125-142.
371. Lambert M., Fletcher L. Review of models for thermal contact conductance of metals. Journal of Thermophysics and Heat Transfer 1997, 11(2):129-140.
372. Incropera F., Dewitt D. Fundamentals of Heat and Mass Transfer 1990, John Wiley. 3rd edn.
373. Bamberger M., Prinz B. Determination of heat transfer coefficients during water cooling of metals. Materials Science and Technology 1986, 2(4):410-415.
374. Goldak J. Modeling thermal stresses and distortions in welds 1989, ASM International, Gatlinburg, USA.
375. Goldak J. Heat and fluid flow in welds. In International Welding Congresson Joining Research 1990, Montreal, Canada.
376. Goldak J. Modeling in Welding, Hot Powder Forming and Casting. Thermal analysis of welds 1997, 17-29. ASM International, Ohio. K. Karlsson (Ed.).
377. Goldak J., et al. Computer modeling of heat flow in welds. Metallurgical Transactions B 1986, 17B:587-600.
378. Goldak J. Computational heat transfer for weld mechanics. In Trends inWelding Research 1986, 15-20. Gatlinburg.
379. Lindgren L.E. Numerical modelling of welding. Computer Methods in Applied Mechanics and Engineering 2006, 195(48-49):6710-6736.
380. Paley Z., Hibbert P. Computation of temperatures in actual weld design. Welding Journal 1975, 54:385s-392s.
381. Friedman E. Analysis of weld puddle distortion and its effect on penetration. Welding Journal June 1978, 161s-166s.
382. Goldak J., Chakravarti A., Bibby M. A new finite element model for welding heat sources. Metallurgical Transactions B 1984, 15B:299-305.
383. Sabapathy P.N., Wahab M.A., Painter M.J. The prediction of burn-through during in-service welding of gas pipelines. International Journal of Pressure Vessels and Piping 2000, 77(11):669-677.
384. Das S., et al. Modeling of Casting, Welding and Advanced Solidification Processes VI. Finite element modeling of a single-pass GMA weldment 1993, The Minerals, Metals &Materials Society.
385. LundbÄCk A. Mathematical Modelling of Weld Phenomena 6. CAD-support for heat input in FE-model 2002, The Institute of Materials, Graz, Austria.
386. Carmet A. Experimental and numerical study of residual stresses and strainsin an electron-beam-welded joint. 1988.
387. Jones B., Emery A., Marburger J. An analytical and experimental study of the effects of welding parameters in fusion welds. Welding Journal 1993, 72(2):51s-59s.
388. Jones B., Emery A., Marburger J. Design and analysis of test coupon for fusion welding. ASME Journal of Pressure Vessel and Technology 1993, 115:38-46.
389. Lindgren L.-E. Mathematical Modelling of Weld Phenomena 6. Welding simulation - 'knowing what isn't necessary to know 2001, The Institute of Materials, Minerals and Mining, Graz, Austria.
390. Berglund D., Runnemalm H. Comparison of deformation pattern and residualstresses in finite element models of a TIG-welded stainless steel plate 2002, ASM International, Pine Mountain,Georgia.
391. Kussmaul K., et al. A contribution to the numerical and experimental determination of residual stresses in welds. Nuclear Engineering 1989, 112:337-348.
392. Lindgren L.E. A welding simulation revisited 1999, Krakow University, Krakow, Poland. J.J. Skrzypek (Ed.).
393. Parkus H. Thermoelasticity 1968, Springer-Verlag. 2nd edn.
394. Barrentine L. Design of Experiments. A Simplified Approach 1999, ASQ Quality Press.
395. Gep B., Hunter W., Hunter J. Statistics for Experimenters: An Introduction to Design, Data Analysis and Model Building 1978, Wiley-Interscience.
396. Olabi A.G., et al. Minimisation of the residual stress in the heat affected zone by means of numerical methods. Materials and Design 24 October 2006, in press, available online. http://www.sciencedirect.com/science?_ob=ArticleURL&udi=B6TX5-4M644Y1-1&user=650452&coverDate=10%2F24%2F2006&alid=562896255&rdoc=3&fmt=full&orig=search&cdi=5581&sort=d&docanchor=&iew=c&ct=3&acct=C000035038&version=1&urlVersion=0&userid=650452&d5=8595df15d467546cf51f2714ec8d9dd2.
397. Casalino G., Curcio F., Memola Capece Minutolo F. Investigation on Ti6Al4V laser welding using statistical and Taguchi approaches. Journal of Materials Processing Technology 2005, 167(2-3):422-428.
398. Wriggers P., Wagner W., Miehe C. A quadratically convergent procedure for the calculation of stability points in finite element analysis. Computer Methods in Applied Mechanics and Engineering 1988, 70(3):329-347.
399. Jonsson M., Karlsson L., Lindgren L.-E. Deformations and stresses in butt-welding of large plates with special reference to the mechanical material properties. Journal of Engineering Materials and Technology 1985, 107(10):265-270.
400. Saint-Germain B., Pilvin P., Gabriel F. Comparison of heat source models andconstitutive laws in finite element modelling of welding distortions confrontation toa TIG fusion line of an austenitit steel thin plate. In Mathematical Modelling ofWeld Phenomena 7 2003, Graz, Austria.
401. Zhu X.K., Chao Y.J. Effects of temperature-dependent material properties on welding simulation. Computers and Structures 2002, Only available online. http://www.sciencedirect.com/science?_ob=ArticleURL&udi=B6TX5-4M644Y1-1&user=650452&coverDate=10%2F24%2F2006&alid=562082244&rdoc=3&fmt=summary&orig=search&cdi=5581&sort=d&docanchor=&iew=c&ct=3&acct=C000035038&version=1&urlVersion=0&userid=650452&d5=d0e15a9a6300f1b097af8ca8b33baeb8.
402. Michaleris P. Prediction of welding distortion. Welding Journal 1997, 76:172s.
403. Deo M., Michaleris P. Elimination of welding induced buckling distortion 2002, ASM International, Pine Mountain,Georgia.
404. Deo M., Sun J., Michaleris P. Prediction of buckling distortion of welded structures. Journal of Science and Technology in Welding 2003, 8(1):55-61.
405. Mackerle J. Finite element analysis and simulation of welding: a bibliography (1976-1996). Modelling and Simulation in Materials Science and Engineering 1996, 4(5):501-533.
406. Mackerle J. Finite element analysis and simulation of welding - an addendum: a bibliography (1996-2001). Modelling and Simulation in Materials Science and Engineering 2002, 10(3):295-318.
407. Goldak J. Predicting distortion and residual stress in complex weldedstructures by designers 2005, Pine Mountain, Georgia, USA.
408. Lu F., et al. Modeling and finite element analysis on GTAW arc and weld pool. Computational Materials Science 2004, 29(3):371-378.
409. Hongyuan F., et al. New general double ellipsoid heat source model. Science and Technology of Welding and Joining 2005, 10(3):361-368.
410. Thiessen R.G., Richardson I.M. A physically based model for microstructure development in a macroscopic heat-affected zone: grain growth and recrystallization. Metallurgical and Materials Transactions 2006, 37B(4):655.
411. Thiessen R., Sietsma J., Richardson I. Microstructural modelling of the HAZin dual-phase steel 2006, Seggau, Austria.
412. Elmer J., et al. Kinetic modeling of phase transformations occurring in the HAZ of C-Mn steel welds based on direct observations. Acta Materialia 2003, 51:3333-3349.
413. Zhang W., Elmer J., Debroy T. Integrated modelling of thermal cycles, austenite formation, grain growth and decomposition in the heat affected zone of carbon steel. Science and Technology of Welding and Joining 2005, 10(5):574-582.
414. Bhadeshia H.K.D.H., Svensson L.E., Gretoft B. A model for the development of microstructure in low-alloy steel (Fe-Mn-Si-C) weld deposits. Acta Metallurgica 1985, 33(7):1271-1283.
415. Elmer J.W., et al. In situ observations of lattice expansion and transformation rates of [alpha] and [beta] phases in Ti-6Al-4V. Materials Science and Engineering A 2005, 391(1-2):104-113.
416. Jensen M., et al. Residual stresses in a welded superalloy disc: characterisation using synchrotron diffraction and numerical process modeling. Metallurgical and Materials Transactions A 2002, 33A:2921-2931.
417. Bergheau J.-M., et al. Viscoplastic behaviour of steels during welding. Science and Technology of Welding and Joining 2004, 9(4):323-330.
418. Wilson E., Bathe K.-J., Peterson F. Finite element analysis of linear and nonlinear heat transfer. Nuclear Engineering and Design 1974, 29:110-124.
419. Preston, R.V., et al., Physically-based constitutive modelling of residual stressdevelopment in welding of aluminium alloy 2024. Acta Materialia, 52(17): 4973±4983.
420. Barsoum Z. Residual Stress Analysis and Fatigue of Welded Structures 2006, Department of Aeronautical and Vehicle Engineering, Royal Institute of Technology, Stockholm.
421. Wei Y.H., et al. Three-dimensional numerical simulation of weld solidification cracking. Modelling and Simulation in Materials Science and Engineering 2005, 13(3):437-454.
422. Dye D., Hunziker O., Reed R. Numerical analysis of the weldability of superalloys. Acta Materialia 2001, 49:683-697.
423. Teng T.-L., Fung C.-P., Chang P.-H. Effect of residual stresses on the fatigue of butt joints using thermal elasto-plastic and multiaxial fatigue theory. Engineering Failure Analysis 2003, 10:131-151.
424. Radaj D. Mathematical Modelling of Weld Phenomena. Integrated finite element analysis of welding residual stress and distortion 2001, Institute of Materials, Minerals and Mining, Graz, Austria.
425. Teng T.-L., Fung C.-P., Chang P.-H. Effect of weld geometry and residual stresses on fatigue in butt-welded joints. International Journal of Pressure Vessels and Piping 2002, 79(7):467-482.
426. Duranton P., et al. 3D modelling of multipass welding of a 316L stainless steel pipe. Journal of Materials Processing Technology 2004, 153-154:457-463.
427. Audronis M., Bendikas J. The welding deformations of chrome-nickel stainless steels. Materials Science 2003, 9(2):22-26.
428. Camilleri D., Gray T.G.F. Computationally efficient welding distortion simulation techniques. Modelling and Simulation in Materials Science and Engineering 2005, 13(8):1365.
429. Camilleri D., Mollicone P., Gray T.G.F. Alternative simulation techniques for distortion of thin plate due to fillet-welded stiffeners. Modelling and Simulation in Materials Science and Engineering 2006, 14(8):1307-1327.
430. Deo M.V., Michaleris P. Mitigation of welding induced buckling distortion using transient thermal tensioning. Science and Technology of Welding and Joining 2003, 8(1):49-63.
431. Van Der Aa E., Hermans M., Richardson I. Conceptual model for stress and strain development during welding with trailing heat sink. Science and Technology of Welding and Joining 2006, 11(4):488-495.
432. Toyoda M., Mochizuki M. Control of mechanical properties in structural steel welds by numerical simulation of coupling among temperature, microstructure, and macro-mechanics. Science and Technology of Advanced Materials 2004, 5(1-2):255-266.
433. Mcdonald E.J., Hallam K.R., Flewitt P.E.J. A strategy for accommodating residual stresses in the assessment of repair weldments based upon measurement of near surface stresses. International Journal of Pressure Vessels and Piping 2005, 82(4):339-346.
434. Elcoate C.D., et al. Three-dimensional multi-pass repair weld simulations. International Journal of Pressure Vessels and Piping 2005, 82(4):244-257.
435. Vinas G., et al. Finite element analysis of residual stresses in a letter-box excavation repair weld for Chapelcross Power Station. International Journal of Pressure Vessels and Piping 2005, 82(4):270-278.
436. Song J., Shanghvi J.Y., Michaleris P. Sensitivity analysis and optimization of thermo-elasto-plastic processes with applications to welding side heater design. Computer Methods in Applied Mechanics and Engineering 2004, 193(42-44):4541-4566.
437. Voutchkov I., et al. Weld sequence optimization: the use of surrogate models for solving sequential combinatorial problems. Computer Methods in Applied Mechanics and Engineering 2005, 194(30-33):3535-3551.
438. Berglund D., Alberg H., Runnemalm H. Simulation of welding and stress relief heat treatment of an aero engine component. Finite Elements in Analysis and Design 2003, 39(9):865-881.
439. Cho J.R., et al. Investigation of residual stress and post weld heat treatment of multi-pass welds by finite element method and experiments. Journal of Materials Processing Technology 2004, 155-156:1690-1695.
440. Thorborg J., Hald J., Hattel J. Stellite failure on a P91HP Valve - Failure Investigation and Modelling of Residual Stress 2004, IIW.
441. Mackerle J. Finite element analysis and simulation of quenching and other heat treatment processes: a bibliography 1976-2001. Computational Materials Science 2003, 27(3):313-332.