Minimizing the entropy generation rate of the plate-finned heat sinks using computational fluid dynamics and combined optimization

Applied Thermal Engineering

Volumn 29, Issue 8-9, 2009, Pages 1872-1879

  Jian hui, Zhou ^a   Chun xin, Yang ^a   Li na, Zhang ^a  

^a BEIHANG UNIVERSITY   (China)

Author keywords

Correlation; Entropy generation minimization (EGM); Heat sink; Numerical simulation; Optimization

Indexed keywords

COMPUTATIONAL FLUID DYNAMICS; COMPUTER SIMULATION; DESIGN OF EXPERIMENTS; ENTROPY; FLUID DYNAMICS; FLUIDS; HEAT SINKS; INTEGER PROGRAMMING; REGRESSION ANALYSIS;

BYPASS FLOWS; COMBINATION OPTIMIZATIONS; CORRELATION; ENTROPY GENERATION MINIMIZATION (EGM); ENTROPY GENERATION RATES; ENTROPY GENERATIONS; FLUID PERFORMANCE; FRICTION FACTORS; MIXED-INTEGER OPTIMIZATIONS; MULTI PARAMETERS; MULTIVARIATE NON-LINEAR REGRESSIONS; NUMERICAL SIMULATION; OPERATIONAL PARAMETERS; OPTIMIZATION PROCEDURES; OVERALL RATES; RESPONSE SURFACE MODELS; THERMAL RESISTANCES;

CONSTRAINED OPTIMIZATION;

EID: 61349164831     PISSN: 13594311     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.applthermaleng.2008.08.001     Document Type: Article

References (42)

1. Richard C.C., and Simons R.E. Review of cooling technologies for computer products. IEEE Transactions on Device and Materials Reliability 4 (2004) 568-585
2. Ralph L.W. Next generation devices for electronic cooling with heat rejection to air. Journal of Heat Transfer 127 (2005) 1-10
3. Mudawar I. Assessment of high-heat-flux thermal management schemes. IEEE Transactions on Components and Packaging Technologies 24 (2001) 122-141
4. Dogruoz M.B. Experiments and modeling of the hydraulic resistance and heat transfer of in-line square pin fin heat sinks with top by-pass flow. International Journal of Heat and Mass Transfer 48 (2005) 5058-5071
5. Yakut K. Experimental investigation of thermal resistance of a heat sink with hexagonal fins. Applied Thermal Engineering 26 (2006) 2262-2271
6. Issa J.S., and Ortega A. Experimental measurements of the flow and heat transfer of a square jet impinging on an array of square pin fins. Journal of Electronic Packaging 128 (2006) 61-70
7. P. Teertstra, M.M. Yovanovich, J.R. Culham, Analytical forced convection modeling of plate fin heat sinks, in: Semiconductor Thermal Measurement and Management Symposium, Fifteenth Annual IEEE, 1999, pp. 34-41.
8. Kim S.Y., and Webb R.L. Analysis of convective thermal resistance in ducted fan-heat sinks. IEEE Transactions on Components and Packaging Technologies 29 (2006) 439-448
9. Kobus C.J., and Oshio T. Development of a theoretical model for predicting the thermal performance characteristics of a vertical pin-fin array heat sink under combined forced and natural convection with impinging flow. International Journal of Heat and Mass Transfer 48 (2005) 1053-1063
10. Sathe S.B. An analytical study of the optimized performance of an impingement heat sink. Journal of Electronic Packaging 126 (2004) 528-534
11. Leon O. Comparison between the standard and staggered layout for cooling fins in forced convection cooling. Journal of Electronic Packaging 125 (2003) 442-446
12. P.H. Oosthuizen, A numerical study of mixed convective heat transfer from a parallel fin heat sink, in: 38th AIAA Thermophysics Conference, Toronto, Ontario Canada, AIAA, 2005, 4824.
13. Knight R.W., and Hall D.J. Heat Sink optimization with application to micro-channels. IEEE Transactions on Components, Hybrids, and Manufacturing Technology 15 (1992) 832-849
14. Krueger W.B. Optimal numerical design of forced convection heat sinks. IEEE Transactions on Components and Packaging Technologies 27 (2004) 417-425
15. Kock D.J., and Visser J.A. Trade-off design of extruded heat sinks using mathematical optimization. Journal of Electronic Packaging 126 (2004) 333-341
16. Parry J. Simulation-based design optimization methodologies applied to CFD. IEEE Transactions on Components and Packaging Technologies 27 (2004) 391-397
17. Bejan A. Entropy Generation Minimization (1995), CRC Press, Boca Raton
18. Bejan A. Entropy Generation Through Heat and Fluid Flow (1982), Wiley, New York
19. Bejan A. Advanced Engineering Thermodynamics (1988), Wiley, New York
20. Bejan A. Optimal internal structure of volumes cooled by single-phase forced and natural convection. Journal of Electronic Packaging 125 (2003) 200-207
21. Bello-Ochende T., and Bejan A. Optimal spacing for mixed convection. Journal of Heat Transfer 126 (2004) 956-962
22. Bejan A. Thermal Design and Optimization (1996), Wiley, New York
23. Sahin A.Z. Second law analysis of laminar viscous flow through a duct subjected to constant wall temperature. International Journal of Heat and Mass Transfer 120 (1998) 76-83
24. Mahmud S., and Fraser R.A. The second law analysis in fundamental convective heat transfer problems. International Journal of Thermal Sciences 42 (2003) 177-186
25. Shuja S.Z., and Yilbas B.S. Flow through a protruding bluff body-heat and irreversibility analysis. Exergy 1 (2001) 209-215
26. Baytas A.C. Entropy generation for natural convection in an inclined porous cavity. International Journal of Heat and Mass Transfer 43 (2000) 2089-2099
27. Dagtekin I., Oztop H.F., and Sahin A.Z. An analysis of entropy generation through a circular duct with different shaped longitudinal fins for laminar flow. International Journal of Heat and Mass Transfer 48 (2005) 71-181
28. Culham J.R. Optimization of plate fin heat sinks using entropy generation minimization. IEEE Transactions on Components and Packaging Technologies 24 (2001) 59-165
29. Khan W.A., and Culham J.R. The influence of material properties and spreading resistance in the thermal design of plate fin heat sinks. Journal of Electronic Packaging 129 (2007) 76-81
30. Khan W.A., and Culham J.R. Optimization of pin-fin heat sinks using entropy generation minimization. IEEE Transactions on Components and Packaging Technologies 28 (2005) 247-254
31. Khan W.A., and Culham J.R. The role of fin geometry in heat sink performance. Journal of Electronic Packaging 128 (2006) 324-330
32. Shih C.J., and Liu G.C. Optimal design methodology of plate-fin heat sinks for electronic cooling using entropy generation strategy. IEEE Transactions on Components and Packaging Technologies 27 (2004) 551-559
33. T. Furukawa, W.J. Yang, Reliability of heat sink optimization using entropy generation minimization, in: AIAA/ASME Joint Thermodynamics and Heat Transfer Conference, St. Louis, MO, AIAA, 2002, 3216.
34. Patankar S.V. Numerical Heat Transfer and Fluid Flow (1980), Hemisphere, Washington, DC
35. R. Hossain, J.R. Culham, Influence of bypass on flow through plate fin heat sinks, in: 23rd IEEE SEMI-THERM Symposium, 2007, pp. 220-227.
36. Chiang K.-T. Optimization of the design parameters of parallel-plain fin heat sink module cooling phenomenon based on the Taguchi method. International Communications in Heat and Mass Transfer 32 (2005) 1193-1201
37. Chiang K.-T. Application of response surface methodology in the parametric optimization of a pin-fin type heat sink. International Communications in Heat and Mass Transfer 33 (2006) 36-845
38. Lian Y. Multiobjective optimization using coupled response surface model and evolutionary algorithm. AIAA Journal 43 (2005) 1316-1325
39. Chen H.-T. Design optimization for pin-fin heat sinks. Journal of Electronic Packaging 127 (2005) 397-406
40. Chen H.-T. Optimal design for PPF heat sinks in electronics cooling applications. Journal of Electronic Packaging 126 (2004) 410-422
41. Wirtz R.A. Thermal performance of pin-fin fan-sink assemblies. Journal of Electronic Packaging 119 (1997) 26-31
42. Zheng N., and Wirtz R.A. Cylindrical pin-fin fan-sink heat transfer and pressure drop correlations. IEEE Transactions on Components and Packaging Technologies 25 (2002) 15-22