Experimental measurements of the flow and heat transfer of a square jet impinging on an array of square pin fins

Journal of Electronic Packaging

Volumn 128, Issue 1, 2006, Pages 61-70

  Issa, Johnny S ^a,b   Ortega, Alfonso ^a,b  

^a ASME   (United States)

^b University of Arizona   (United States)

Author keywords

Electronics cooling; Impinging jet; Pin fin heat sinks

Indexed keywords

COOLING; ELECTRONIC EQUIPMENT; FLOW OF FLUIDS; HEAT RESISTANCE; HEAT TRANSFER; REYNOLDS NUMBER;

AIR JET IMPINGEMENT; IMPINGING JET; PIN FIN HEAT SINKS; PRESSURE LOSS COEFFICIENT;

FINS (HEAT EXCHANGE);

EID: 33646004310     PISSN: 10437398     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2160513     Document Type: Article

References (15)

1. Shaukatullah, H., Storr, W. R., Hansen, B. J., and Gaynes, M. A., 1996, "Design and Optimization of Pin Fin Heat Sinks for Low Velocity Applications," Proceedings of the 12th IEEE SEMI-THERM Symposium, IEEE, Austin, pp. 151-163.
2. Dogruoz, M. B., Urdaneta, M., and Ortega, A., 2005, "Experiments and Modeling of the Hydraulic Resistance and Heat Transfer of In-line Square Pin Fin Heat Sinks with Top By-pass Flow," Int. J. Heat Mass Transfer, 48, pp. 5058-5071.
3. Maudgal, V. K., and J. E. Sunderland, 1997, "An Experimental Study of Forced Convection Heat Transfer from In-line Pin-Fin Arrays," Proceedings of the 13th IEEE SEMI-THERM Symposium, IEEE, New York, pp. 149-157.
4. Martin, H., 1977, "Heat and Mass Transfer Between Impinging Gas Jets and Solid Surfaces," Advances in Heat Transfer, Academic, Orlando, Vol. 13, pp. 1-60.
5. Amano, R. S., 2000, "Electronic Cooling Technology with the Use of Turbulent Impinging Jets," Proceedings of the 2000 International Conference on Thermal Mechanics and Thermomechanical Phenomena in Electronic Systems, (ITHERM), Las Vegas, Nevada, pp. 339-346.
6. Guarino, J. R., and Manno, V. P., 2001 "Characterization of Laminar Jet Impingement Cooling in Portable Computer Applications," Proceedings of the 17th IEEE SEMI-THERM Symposium, IEEE, San Jose, California, pp. 1-11.
7. Jung, H. H., and Maveety, J. G., 2000, "Pin Fin Heat Sink Modeling and Characterization," Proceedings of the 16th IEEE SEMI-THERM Symposium, IEEE, San Jose, California, pp. 260-265.
8. Brignoni, L. A., and Garimella, S. V., 1999, "Experimental Optimization of Confined Air Jet Impingement on a Pin Fin Heat Sink," IEEE Trans. Compon. Packag. Technol., 22, pp. 399-404.
9. El-Sheikh, H. A., and Garimella, S. V., 2000, "Enhancement of Air Jet Impingement Heat Transfer Using Pin-Fin Heat Sinks," IEEE Trans. Compon. Packag. Technol., 23. pp. 300-308.
10. Moffat, R. J., 1988, "Describing the Uncertainties in Experimental Results," Exp. Therm. Fluid Sci., 1, pp. 3-17.
11. Danek, C. J., and Moffat, R. J., 1995, "Heat Transfer under Impinging Jets at Very Close Jet-to-Target Spacings," Report No. HMT-50, Thermosciences Division, Department of Mechanical Engineering, Stanford University.
12. TAS - Thermal Analysis System, 2001, Harvard Thermal Inc., Harvard, Massachusetts, USA.
13. Issa, J. S., 2002, "Experimental Study of the Flow and Heat Transfer of Square Jet Impinging on Pin Fin Heat Sinks," M.S. thesis. The University of Arizona, Tucson.
14. Figliola, R. S., and Beasley, D. E., 1995, Theory and Design for Mechanical Measurements, Wiley, New York, pp. 125-169.
15. Incropera, F. P., and DeWitt, D. P., 1996, Fundamentals of Heat and Mass Transfer, Wiley, New York, pp. 110-134.