Material processing of hydroxyapatite and titanium alloy (HA/Ti) composite as implant materials using powder metallurgy: A review

Materials and Design

Volumn 55, Issue , 2014, Pages 165-175

  Arifin, Amir ^a,b   Sulong, Abu Bakar ^a   Muhamad, Norhamidi ^a   Syarif, Junaidi ^a   Ramli, Mohd Ikram ^a  

^a UNIVERSITI KEBANGSAAN MALAYSIA   (Malaysia)

^b SRIWIJAYA UNIVERSITY   (Indonesia)

Author keywords

Biocompatibility; Ceramic metal composite; Material processing; Mechanical properties; Powder metallurgy

Indexed keywords

BIOCOMPATIBILITY; BIOLOGICAL MATERIALS; ELASTIC MODULI; HYDROXYAPATITE; MECHANICAL PROPERTIES; PLASMA SPRAYING; POWDER METALLURGY; SINTERING; TITANIUM ALLOYS;

CERAMIC METAL COMPOSITES; DIFFUSION MECHANISMS; ISOSTATIC PRESSING; LOW YOUNG'S MODULUS; MATERIAL PROCESSING; METAL INJECTION MOLDING; POWDER METALLURGY PROCESS; RHEOLOGICAL BEHAVIORS;

STRENGTH OF MATERIALS;

EID: 84886617556     PISSN: 02613069     EISSN: 18734197     Source Type: Journal    
DOI: 10.1016/j.matdes.2013.09.045     Document Type: Review

References (119)

1. Li Z.X., Kawashita M. Current progress in inorganic artificial biomaterials. J Artif Organs 2011, 14:163-170.
2. Ferreira C.F., Magini R.S., Sharpe P.T. Biological tooth replacement and repair. J Oral Rehab 2007, 34:933-939.
3. Best S.M., Porter A.E., Thian E.S., Huang J. Bioceramics: past, present and for the future. J Eur Ceram Soc 2008, 28:1319-1327.
4. Hench L.L., Thompson I. Twenty-first century challenges for biomaterials. J Roy Soc Interface 2010, 7:S379-S391.
5. Dorozhkin S.V. Bioceramics of calcium orthophosphates. Biomaterials 2010, 31:1465-1485.
6. Niespodziana K., Jurczyk K., Jakubowicz J., Jurczyk M. Fabrication and properties of titanium-hydroxyapatite nanocomposites. Mater Chem Phys 2010, 123:160-165.
7. Thian E.S., Huang J., Best S.M., Barber Z.H., Bonfield W. Magnetron co-sputtered silicon-containing hydroxyapatite thin films - an in vitro study. Biomaterials 2005, 26:2947-2956.
8. Thian E.S., Loh N.H., Khor K.A., Tor S.B. In vitro behavior of sintered powder injection molded Ti-6Al-4V/HA. J Biomed Mater Res 2002, 63:79-87.
9. Hayashi N., Ueno S., Kornarov S.V., Kasai E., Oki T. Fabrication of hydroxyapatite coatings by the ball impact process. Surf Coat Technol 2012, 206:3949-3954.
10. Murakami M., Nomura N., Doi H., Tsutsumi Y., Nakamura H., Chiba A., et al. Microstructures of Zr-added Co-Cr-Mo alloy compacts fabricated with a metal injection molding process and their metal release in 1 mass% lactic acid. Mater Trans 2010, 51:1281-1287.
11. Shirtliff V.J., Hench L.L. Bioactive materials for tissue engineering, regeneration and repair. J Mater Sci 2003, 38:4697-4707.
12. Dourandish M., Godlinski D., Simchi A., Firouzdor V. Sintering of biocompatible P/M Co-Cr-Mo alloy (F-75) for fabrication of porosity-graded composite structures. Mater Sci Eng A-Struct 2008, 472:338-346.
13. Sopyan I., Mel M., Ramesh S., Khalid K.A. Porous hydroxyapatite for artificial bone applications. Sci Technol Adv Mater 2007, 8:116-123.
14. Jurczyk M., Jurczyk K., Niespodziana K. The manufacturing of titanium-hydroxyapatite nanocomposites for bone implant applications. Nanopages 2006, 1:219-229.
15. Nath S., Kalmodia S., Basu B. Densification, phase stability and in vitro biocompatibility property of hydroxyapatite-10wt% silver composites. J Mater Sci-Mater Med 2010, 21:1273-1287.
16. Torres Y., Pavon J.J., Nieto I., Rodriguez J.A. Conventional powder metallurgy process and characterization of porous titanium for biomedical applications. Metall Mater Trans B 2011, 42:891-900.
17. Akahori T., Niinomi M., Koyanagi Y., Kasuga T., Toda H., Fukui H., et al. Mechanical properties of biocompatible beta-type titanium alloy coated with calcium phosphate invert glass-ceramic layer. Mater Trans 2005, 46:1564-1569.
18. Carr B.C., Goswami T. Knee implants - review of models and biomechanics. Mater Des 2009, 30:398-413.
19. Helmus M.N., Gibbons D.F., Cebon D. Biocompatibility: meeting a key functional requirement of next-generation medical devices. Toxicol Pathol 2008, 36:70-80.
20. Sasikumar Y., Rajendran N. Surface modification and in vitro characterization of Cp-Ti and Ti-5Al-2Nb-1Ta alloy in simulated body fluid. J Mater Eng Perform 2012, 21:2177-2187.
21. Yoshikawa H., Tamai N., Murase T., Myoui A. Interconnected porous hydroxyapatite ceramics for bone tissue engineering. J Roy Soc, Interface/Roy Soc 2009, 6(Suppl. 3):S341-S348.
22. Brentel A.S., de Vasconcellos L.M., Oliveira M.V., Graca M.L., de Vasconcellos L.G., Cairo C.A., et al. Histomorphometric analysis of pure titanium implants with porous surface versus rough surface. J Appl Oral Sci 2006, 14:213-218.
23. Gross K.A., Muller D., Lucas H., Haynes D.R. Osteoclast resorption of thermal spray hydoxyapatite coatings is influenced by surface topography. Acta Biomater 2012, 8:1948-1956.
24. Bansiddhi A., Dunand D.C. Processing of NiTi foams by transient liquid phase sintering. J Mater Eng Perform 2011, 20:511-516.
25. Chen L.J., Li T., Li Y.M., He H., Hu Y.H. Porous titanium implants fabricated by metal injection molding. Trans Nonferr Met Soc China 2009, 19:1174-1179.
26. Manonukul A., Muenya N., Leaux F., Amaranan S. Effects of replacing metal powder with powder space holder on metal foam produced by metal injection moulding. J Mater Process Technol 2010, 210:529-535.
27. Park J.W., Kim Y.J., Park C.H., Lee D.H., Ko Y.G., Jang J.H., et al. Enhanced osteoblast response to an equal channel angular pressing-processed pure titanium substrate with microrough surface topography. Acta Biomater 2009, 5:3272-3280.
28. Puckett S.D., Lee P.P., Ciombor D.M., Aaron R.K., Webster T.J. Nanotextured titanium surfaces for enhancing skin growth on transcutaneous osseointegrated devices. Acta Biomater 2010, 6:2352-2362.
29. Webster T.J., Ejiofor J.U. Increased osteoblast adhesion on nanophase metals: Ti, Ti6Al4V, and CoCrMo. Biomaterials 2004, 25:4731-4739.
30. Karrholm J., Razaznejad R. Fixation and bone remodeling around a low stiffness stem in revision surgery. Clin Orthop Relat R 2008, 466:380-388.
31. Spoerke E.D., Murray N.G., Li H.L., Brinson L.C., Dunand D.C., Stupp S.I. A bioactive titanium foam scaffold for bone repair. Acta Biomater 2005, 1:523-533.
32. Nakano T., Kan T., Ishimoto T., Ohashi Y., Fujitani W., Umakoshi Y., et al. Evaluation of bone quality near metallic implants with and without lotus-type pores for optimal biomaterial design. Mater Trans 2006, 47:2233-2239.
33. Kawahara H. Bioceramics for hard tissue replacements. Clin Mater 1987, 2:181-206.
34. Niinomi M. Mechanical biocompatibilities of titanium alloys for biomedical applications. J Mech Behav Biomed 2008, 1:30-42.
35. Nomura N., Sakamoto K., Takahashi K., Kato S., Abe Y., Doi H., et al. Fabrication and mechanical properties of porous Ti/HA composites for bone fixation devices. Mater Trans 2010, 51:1449-1454.
36. CORE-Materials. Materials selection of femoral stem component. University of Cambridge; 2006. Retrieved from: http://www.doitpoms.ac.uk/tlplib/bones/stem.php.
37. Callister W. Materials science and eng an introduction 2009, Wiley. 6th ed.
38. Cui C., Hu B., Zhao L., Liu S. Titanium alloy production technology, market prospects and industry development. Mater Des 2011, 32:1684-1691.
39. Zhang W., Zhu Z., Cheng C.Y. A literature review of titanium metallurgical processes. Hydrometallurgy 2011, 108:177-188.
40. Bertol L.S., Júnior W.K., Silva F.P.d., Aumund-Kopp C. Medical design: direct metal laser sintering of Ti-6Al-4V. Mater Des 2010, 31:3982-3988.
41. Nie L., Zhan Y., Liu H., Tang C. Novel β-type Zr-Mo-Ti alloys for biological hard tissue replacements. Mater Des 2014, 53:8-12.
42. Niinomi M., Nakai M. Titanium-based biomaterials for preventing stress shielding between implant devices and bone. Int J Biomater 2011, 2011:836587.
43. Leyens C., Peters M. Titanium and titanium alloys 2006, John Wiley & Sons.
44. Schaller W.T. The composition of the phosphokite minerals. Mineralogical notes. Bulletin 1912, 509:98-100.
45. Tõnsuaadu K., Gross K.A., Pluduma L., Veiderma M. A review on the thermal stability of calcium apatites. J Therm Anal Calorim 2011.
46. Ruys A.J., Wei M., Sorrell C.C., Dickson M.R., Brandwood A., Milthorpe B.K. Sintering effects on the strength of hydroxyapatite. Biomaterials 1995, 16:409-415.
47. Tampieri A., Celotti G., Sprio S., Mingazzini C. Characteristics of synthetic hydroxyapatites and attempts to improve their thermal stability. Mater Chem Phys 2000, 64:54-61.
48. Chang B.-S., Lee iCKfC.-K., Hong K.-S., Youn H.-J., Ryu H.-S., Chung S.-S., et al. Osteoconduction at porous hydroxyapatite with various pore configurations. Biomaterials 2000, 21:1291-1298.
49. Biemond J.E., Eufrasio T.S., Hannink G., Verdonschot N., Buma P. Assessment of bone ingrowth potential of biomimetic hydroxyapatite and brushite coated porous E-beam structures. J Mater Sci-Mater Med 2011, 22:917-925.
50. Oh I.-H., Nomura N., Masahashi N., Hanada S. Mechanical properties of porous titanium compacts prepared by powder sintering. Scripta Mater 2003, 49:1197-1202.
51. Karageorgiou V., Kaplan D. Porosity of 3D biomaterial scaffolds and osteogenesis. Biomaterials 2005, 26:5474-5491.
52. Vasconcellos LMRd, Oliveira MVd, Graça M.L.d.A., Vasconcellos LGOd, Carvalho Y.R., Cairo C.A.A. Porous titanium scaffolds produced by powder metallurgy for biomedical applications. Mater Res 2008, 11:275-280.
53. Vasconcellos L.M., Leite D.O., Nascimento F.O., Vasconcellos L.G., Graca M.L., Carvalho Y.R., et al. Porous titanium for biomedical applications: an experimental study on rabbits. Med Oral Patol Oral 2010, e12-e407.
54. Ryan G., Pandit A., Apatsidis D.P. Fabrication methods of porous metals for use in orthopaedic applications. Biomaterials 2006, 27:2651-2670.
55. Mour M., Das D., Winkler T., Hoenig E., Mielke G., Morlock M.M., et al. Advances in porous biomaterials for dental and orthopaedic applications. Materials 2010, 3:2947-2974.
56. Chen L.-J., Li T., Li Y.-M., He H., Hu Y.-H. Porous titanium implants fabricated by metal injection molding. Trans Nonferr Met Soc China 2009, 19:1174-1179.
57. Dezfuli S.N., Sadrnezhaad S.K., Shokrgozar M.A., Bonakdar S. Fabrication of biocompatible titanium scaffolds using space holder technique. J Mater Sci-Mater Med 2012, 23:2483-2488.
58. Kohl M., Bram M., Moser A., Buchkremer H.P., Beck T., Stover D. Characterization of porous, net-shaped NiTi alloy regarding its damping and energy-absorbing capacity. Mater Sci Eng A-Struct 2011, 528:2454-2462.
59. Egorov A., Smirnov V., Shvorneva L., Kutsev S., Barinov S. High-temperature hydroxyapatite-titanium interaction. Inorg Mater 2010, 46:168-171.
60. Yang Y., Kim K.-H., Agrawal C.M., Ong J.L. Interaction of hydroxyapatite-titanium at elevated temperature in vacuum environment. Biomaterials 2004, 25:2927-2932.
61. Salman S., Gunduz O., Yilmaz S., Öveçoǧlu M.L., Snyder R.L., Agathopoulos S., et al. Sintering effect on mechanical properties of composites of natural hydroxyapatites and titanium. Ceram Int 2009, 35:2965-2971.
62. Berezhnaya A., Mittova V., Kostyuchenko A., Mittova I. Solid-phase interaction in the hydroxyapatite/titanium heterostructures upon high-temperature annealing in air and argon. Inorg Mater 2008, 44:1214-1217.
63. Thian E.S., Loh N.H., Khor K.A., Tor S.B. Microstructures and mechanical properties of powder injection molded Ti-6Al-4V HA powder. Biomaterials 2002, 23:2927-2938.
64. Ye H., Liu X., Hong H. Characterization of sintered titanium/hydroxyapatite biocomposite using FTIR spectroscopy. J Mater Sci-Mater Med 2009, 20:843-850.
65. Balbinotti P., Gemelli E., Buerger G., de Lima S.A., de Jesus J., Camargo N.H.A., et al. Microstructure development on sintered Ti/HA biocomposites produced by powder metallurgy. Mater Res-Ibero-Am J 2011, 14:384-393.
66. Chu C., Xue X., Zhu J., Yin Z. Fabrication and characterization of titanium-matrix composite with 20vol% hydroxyapatite for use as heavy load-bearing hard tissue replacement. J Mater Sci-Mater Med 2006, 17:245-251.
67. Chu C., Lin P., Dong Y., Xue X., Zhu J., Yin Z. Fabrication and characterization of hydroxyapatite reinforced with 20vol% Ti particles for use as hard tissue replacement. J Mater Sci-Mater Med 2002, 13:985-992.
68. Chu C.L., Xue X.Y., Zhu J.C., Yin Z.D. Mechanical and biological properties of hydroxyapatite reinforced with 40vol.% titanium particles for use as hard tissue replacement. J Mater Sci-Mater Med 2004, 15:665-670.
69. Shi W., Kamiya A., Zhu J., Watazu A. Properties of titanium biomaterial fabricated by sinter-bonding of titanium/hydroxyapatite composite surface-coated layer to pure bulk titanium. Mater Sci Eng A-Struct 2002, 337:104-109.
70. Lu Y.P., Li M.S., Li S.T., Wang Z.G., Zhu R.F. Plasma-sprayed hydroxyapatite+titania composite bond coat for hydroxyapatite coating on titanium substrate. Biomaterials 2004, 25:4393-4403.
71. Nelea V., Morosanu C., Bercu M., Mihailescu I.N. Interfacial titanium oxide between hydroxyapatite and TiAlFe substrate. J Mater Sci-Mater Med 2007, 18:2347-2354.
72. Meguid S.A. Mechanics and mechanisms of toughening of advanced ceramics. J Mater Process Technol 1996, 56:978-989.
73. Zhang L., Webster T.J. Nanotechnology and nanomaterials: promises for improved tissue regeneration. Nano Today 2009, 4:66-80.
74. Webster T.J., Ergun C., Doremus R.H., Siegel R.W., Bizios R. Enhanced functions of osteoblasts on nanophase ceramics. Biomaterials 2000, 21:1803-1810.
75. Okada S., Ito H., Nagai A., Komotori J., Imai H. Adhesion of osteoblast-like cells on nanostructured hydroxyapatite. Acta Biomater 2010, 6:591-597.
76. Misra R.D.K., Thein-Han W.W., Pesacreta T.C., Somani M.C., Karjalainen L.P. Biological significance of nanograined/ultrafine-grained structures: interaction with fibroblasts. Acta Biomater 2010, 6:3339-3348.
77. Jurczyk M.U., Jurczyk K., Miklaszewski A., Jurczyk M. Nanostructured titanium-4555 bioglass scaffold composites for medical applications. Mater Des 2011, 32:4882-4889.
78. Niespodziana K., Jurczyk K., Jakubowicz J., Jurczyk M. Fabrication and properties of titanium-hydroxyapatite nanocomposites. Mater Chem Phys 2010, 123:160-165.
79. Farnoush H., Sadeghi A., Bastami A.A., Moztarzadeh F., Mohandesi J.A. An innovative fabrication of nano-HA coatings on Ti-CaP nanocomposite layer using a combination of friction stir processing and electrophoretic deposition. Ceram Int 2013, 39:1477-1483.
80. MedicineNet.com Webster's new world medical dictionary 2009, John Wiley & Sons, Incorporated.
81. Gu Y.W., Khor K.A., Cheang P. In vitro studies of plasma-sprayed hydroxyapatite/Ti-6Al-4V composite coatings in simulated body fluid (SBF). Biomaterials 2003, 24:1603-1611.
82. Ning C.Q., Zhou Y. In vitro bioactivity of a biocomposite fabricated from HA and Ti powders by powder metallurgy method. Biomaterials 2002, 23:2909-2915.
83. Ning C.Q., Zhou Y. Correlations between the in vitro and in vivo bioactivity of the Ti/HA composites fabricated by a powder metallurgy method. Acta Biomater 2008, 4:1944-1952.
84. Alzubaydi T.L., AlAmeer S.S., Ismaeel T., AlHijazi A.Y., Geetha M. In vivo studies of the ceramic coated titanium alloy for enhanced osseointegration in dental applications. J Mater Sci-Mater Med 2009, 20:35-42.
85. Ning C., Zhou Y. Correlations between the in vitro and in vivo bioactivity of the Ti/HA composites fabricated by a powder metallurgy method. Acta Biomater 2008, 4:1944-1952.
86. Quan R.F., Yang D.S., Wu X.C., Wang H.B., Miao X.D., Li W. In vitro and in vivo biocompatibility of graded hydroxyapatite-zirconia composite bioceramic. J Mater Sci-Mater Med 2008, 19:183-187.
87. Powder metallurgy. Encyclopedic dictionary of polymers 2007, 779. Springer, New York. J. Gooch (Ed.).
88. Kipouros G.J., Caley W.F., Bishop D.P. On the advantages of using powder metallurgy in new light metal alloy design. Metall Mater Trans A 2006, 37:3429-3436.
89. Pramanik S., Agarwal A.K., Rai K.N., Garg A. Development of high strength hydroxyapatite by solid-state-sintering process. Ceram Int 2007, 33:419-426.
90. Thian E.S., Loh N.H., Khor K.A., Tor S.B. Ti-6A1-4V HA composite feedstock for injection molding. Mater Lett 2002, 56.
91. Patil D.S., Sreekumar K.P., Venkataramani N., Iyer R.K., Prasad R., Koppikar R.S. Plasma sprayed hydroxy apatite coatings. B Mater Sci. 1996, 19:115-121.
92. Yang C.Y., Wang B.C., Chang E., Wu B.C. Bond degradation at the plasma-sprayed HA coating/Ti-6AI-4V alloy interface: an in vitro study. J Mater Sci-Mater Med 1995, 6:258-265.
93. Singh G., Singh S., Prakash S. Surface characterization of plasma sprayed pure and reinforced hydroxyapatite coating on Ti6Al4V alloy. Surf Coat Technol 2011, 205:4814-4820.
94. Groover M.P. Fundamentals of modern manufacturing: materials, processes, and systems 2010, John Wiley & Sons.
95. German R.M., Bose A. Injection molding of metals and ceramics 1997, Metal Powder Industries Federation.
96. Thian E.S., Loh N.H., Khor K.A., Tor S.B. Processing of biocomposite Ti-6Al-4V HA powder. J Mater Sci Lett 2003, 22:775-778.
97. Mashl S., Hebeisen J., Hjorth C. Producing large P/M near-net shapes using hot isostatic pressing. Jom-Us 1999, 51:29-31.
98. Atkinson H.V., Davies S. Fundamental aspects of hot isostatic pressing: an overview. Metall Mater Trans A 2000, 31:2981-3000.
99. Lograsso B.K., Koss D.A. Densification of titanium powder during hot isostatic pressing. MTA 1988, 19:1767-1773.
100. Ishizaki K., Nanko M. A hot isostatic process for fabricating porous materials. J Porous Mater 1995, 1:19-27.
101. Zhang K., Mei J., Wain N., Wu X. Effect of hot-isostatic-pressing parameters on the microstructure and properties of powder Ti-6Al-4V hot-isostatically-pressed samples. Metall Mater Trans A 2010, 41:1033-1045.
102. Onoki T., Hashida T. New method for hydroxyapatite coating of titanium by the hydrothermal hot isostatic pressing technique. Surf Coat Technol 2006, 200:6801-6807.
103. Yugeswaran S., Yoganand C.P., Kobayashi A., Paraskevopoulos K.M., Subramanian B. Mechanical properties, electrochemical corrosion and in-vitro bioactivity of yttria stabilized zirconia reinforced hydroxyapatite coatings prepared by gas tunnel type plasma spraying. J Mech Behav Biomed 2012, 9:22-33.
104. Oktar F.N., Yetmez M., Agathopoulos S., Goerne T.M.L., Goller G., Ipeker I., et al. Bond-coating in plasma-sprayed calcium-phosphate coatings. J Mater Sci-Mater Med 2006, 17:1161-1171.
105. 2 intermediate layer. J Therm Spray Technol 2003, 12:199-207.
106. Zheng X., Huang M., Ding C. Bond strength of plasma-sprayed hydroxyapatite/Ti composite coatings. Biomaterials 2000, 21:841-849.
107. Yang Y.C., Chang E. The bonding of plasma-sprayed hydroxyapatite coatings to titanium: effect of processing, porosity and residual stress. Thin Solid Films 2003, 444:260-275.
108. Morks M.F., Kobayashi A. Influence of spray parameters on the microstructure and mechanical properties of gas-tunnel plasma sprayed hydroxyapatite coatings. Mater Sci Eng: B 2007, 139:209-215.
109. Khor K.A., Yip C.S., Cheang P. Post-spray hot isostatic pressing of plasma sprayed Ti6Al4V/hydroxyapatite composite coatings. J Mater Process Technol 1997, 71:280-287.
110. Abdel-Samad A., Lugscheider E., Bobzin K., Maes M. The influence of hot isostatic pressing on plasma sprayed coatings properties. Surf Coat Technol 2006, 201:1224-1227.
111. Ye H., Liu X.Y., Hong H. Fabrication of metal matrix composites by metal injection molding-a review. J Mater Process Technol 2008, 200:12-24.
112. Huang B., Liang S., Qu X. The rheology of metal injection molding. J Mater Process Technol 2003, 137:132-137.
113. Heaney D.F., Gurosik J.D., Binet C. Isotropic forming of porous structures via metal injection molding. J Mater Sci 2005, 40:973-981.
114. Berginc B., Kampus Z., Sustarsic B. Influence of feedstock characteristics and process parameters on properties of MIM parts made of 316L. Powder Metall 2007, 50:172-183.
115. Hartwig T., Veltl G., Petzoldt F., Kunze H., Scholl R., Kieback B. Powders for metal injection molding. J Eur Ceram Soc 1998, 18:1211-1216.
116. Duggirala R., Shivpuri R. Effects of processing parameters in P/M steel forging on part properties: a review Part I powder preparation, compaction, and sintering. J Mater Eng Perform 1992, 1:495-503.
117. Ismail M.H., Goodall R., Davies H.A., Todd I. Porous NiTi alloy by metal injection moulding/sintering of elemental powders: effect of sintering temperature. Mater Lett 2012, 70:142-145.
118. Thian E.S., Loh N.H., Khor K.A., Tor S.B. Effects of debinding parameters on powder injection molded Ti-6Al-4V/HA composite parts. Adv Powder Technol 2001, 12:361-370.
119. Thian E.S., Khor K.A., Loh N.H., Tor S.B. Processing of HA-coated Ti-6Al-4V by a ceramic slurry approach: an in vitro study. Biomaterials 2001, 22:1225-1232.