Surface finishing of micro-EDM holes using deionized water

Journal of Micromechanics and Microengineering

Volumn 19, Issue 4, 2009, Pages

  Chung, Do Kwan ^a   Shin, Hong Shik ^a   Kim, Bo Hyun ^b   Park, Min Soo ^c   Chu, Chong Nam ^a  

^a Seoul National University   (South Korea)

^b Andong National University   (South Korea)

^c Wonkwang University   (South Korea)

Author keywords

[No Author keywords available]

Indexed keywords

DIELECTRIC FLUID; ELECTROCHEMICAL DISSOLUTION; FINISHING PROCESS; FINISHING TIME; INNER SURFACES; MICRO EDM; MICRO ELECTRICAL DISCHARGE MACHINING; MICRO HOLES; SURFACE FINISHING; SURFACE QUALITIES; TOOL ROTATIONS;

DISSOLUTION; ELECTRIC DIPOLE MOMENTS; ELECTRIC DISCHARGE MACHINING; ELECTRIC DISCHARGES; ELECTRIC POTENTIAL; MICROMACHINING; ROTATION; SURFACE ROUGHNESS;

DEIONIZED WATER;

EID: 67849119667     PISSN: 09601317     EISSN: 13616439     Source Type: Journal    
DOI: 10.1088/0960-1317/19/4/045025     Document Type: Article

References (24)

1. Ahn S H, Ryu S H, Choi D K and Chu C N 2004 Electro-chemical micro drilling using ultra short pulses Precis. Eng. 28 129-34
2. Kim B H, Ryu S H, Choi D K and Chu C N 2005 Micro electrochemical milling J. Micromech. Microeng. 15 124-9
3. Kim B H, Na C W, Lee Y S, Choi D K and Chu C N 2005 Micro electrochemical machining of 3D micro structure using dilute sulfuric acid Ann. CIRP 54 191-4
4. Kim B H, Park B J and Chu C N 2006 Fabrication of multiple electrodes by reverse EDM and their application in micro ECM J. Micromech. Microeng. 16 843-50
5. Na C W, Kim B H, Shin H S and Chu C N 2007 Micro wire electrochemical machining 15th Int. Symp. on Electromachining (ISEM XV) (Pittsburgh, PA, USA, 23-27 April 2007) pp 329-33
6. Masuzawa T 2000 State of the art of micromachining Ann. CIRP 49 473-88
7. Masuzawa T, Tsukanoto J and Fujimoto M 1989 Drilling of deep microholes by EDM Ann. CIRP 38 195-8
8. Kunieda M, Lauwers B, Rarjurkar K P and Schumacher B M 2005 Advancing EDM through fundamental insight into the process Ann. CIRP 54 599-622
9. Chung D K, Kim B H and Chu C N 2007 Micro electrical discharge milling using deionized water as a dielectric fluid J. Micromech. Microeng. 17 867-74
10. Masuzawa T, Fujino M and Kobayashi K 1985 Wire electro-discharge grinding for micro-machining Ann. CIRP 34 431-4
11. Yu Z Y, Masuzawa T and Fujino M 1998 Micro-EDM for three-dimensional cavities-development of uniform wear method Ann. CIRP 47 169-72
12. Rajurkar K P, Levy G, Malshe A, Sundaram M M, McGeough J, Hu X, Resnick R and DeSilva A 2006 Micro and nano machining by electro-physical and chemical processes Ann. CIRP 55 643-66
13. Uhlmann E, Piltz S and Doll U 2005 Machining of micro/miniature dies and moulds by electrical discharge machining-recent development J. Mater. Process. Technol. 167 488-93
14. Takahata K and Gianchandani Y B 2002 Batch mode micro-electro-discharge machining J. Microelectromech. Syst. 11 102-10
15. Ok J G, Kim B H, Sung W Y, Chu C N and Kim Y H 2007 Uniformity enhancement of carbon nanofiber emitters via electrical discharge machining Appl. Phys. Lett. 90 033117 (3p)
16. Kim B H, Ok J G, Kim Y H and Chu C N 2007 Electrical discharge machining of carbon nanofiber for uniform field emission Ann. CIRP 56 233-6
17. Ok J G, Kim B H, Chung D K, Sung W Y, Lee S M, Lee S W, Kim W J, Park J W, Chu C N and Kim Y H 2008 Electrical discharge machining of carbon nanomaterials in air: machining characteristics and the advanced field emission applications J. Micromech. Microeng. 18 25007
18. Yi S M, Jin S H, Lee J D and Chu C N 2005 Fabrication of a high-aspect-ratio stainless steel shadow mask and its application to pentacene thin-film transistors J. Micromech. Microeng. 15 263-9
19. Yi S M, Park M S, Lee Y S and Chu C N 2008 Fabrication of a stainless steel shadow mask using batch mode micro-EDM Microsyst. Technol. 14 411-7
20. Takahata K, Aoki S and Sato T 1996 Fine surface finishing method for 3-dimensional micro structures Proc. IEEE MEMS 73-8
21. Kurita T and Hattori M 2006 A study of EDM and ECM/ECM-lapping complex machining technology Int. J. Mach. Tools Manuf. 46 1804-10
22. Campana S and Miyazawa S 1999 Micro EDM and ECM in DI water Proc. ASPE Annual Meeting
23. Masuzawa T, Kuo C L and Fujino M 1994 A combined electrical machining process for micronozzle fabrication Ann. CIRP 43 189-92
24. Hung J C, Yan B H, Liu H S and Chow H M 2006 Micro-hole machining using micro-EDM combined with electropolishing J. Micromech. Microeng. 16 1480-6