Influence of cutting tool constitutive parameters on residual stresses induced by hard turning

International Journal of Machining and Machinability of Materials

Volumn 4, Issue 1, 2008, Pages 39-50

  Rech, Joël ^a   Claudin, Christophe ^a  

^a UNIVERSITÉ DE LYON   (France)

Author keywords

Composition; Cutting tool geometry; Hard turning; Residual stresses; Surface integrity

Indexed keywords

BINARY ALLOYS; CHEMICAL ANALYSIS; CHROMIUM ALLOYS; CHROMIUM STEEL; COATINGS; CUBIC BORON NITRIDE; GEOMETRY; MANGANESE ALLOYS; MANGANESE STEEL; RESIDUAL STRESSES; SURFACE ROUGHNESS; TITANIUM NITRIDE;

COMPRESSIVE RESIDUAL STRESS; CONSTITUTIVE PARAMETERS; CUTTING EDGE GEOMETRY; CUTTING TOOL GEOMETRY; HARD TURNING; STRATEGIC PARAMETER; SURFACE INTEGRITY; X-RAY DIFFRACTION MEASUREMENTS;

CUTTING TOOLS;

EID: 54949083103     PISSN: 17485711     EISSN: 1748572X     Source Type: Journal    
DOI: 10.1504/IJMMM.2008.020909     Document Type: Article

References (29)

1. Abrao, A.M. and Aspinwall, D.K. (1996) 'The surface integrity of turned and ground hardened bearing steel', Wear, Vol. 196, pp.279-284.
2. Agha, S.R. and Liu, C.R. (2000) 'Experimental study on the performance of superfinishing hard turned surfaces in rolling contact', Wear, Vol. 244, pp.52-59.
3. Bhushan, B. (2001) Modern Tribology Handbook - Tome 2, Editions CRC Press, ISBN 0-8493-8403-690000.
4. Choi, Y. and Liu, C.R. (2006) 'Rolling contact fatigue life of finish hard materials surfaces. Part 2. Experimental verification', Wear, Vol. 261, pp.492-499.
5. Cullity, B.D. (1978) Elements of X-Ray Diffraction, 2nd edition, Addison-Wesley Publishing Company, Inc.
6. Dahlman, P., Gunnberg, F. and Jacobson, M. (2004) 'The influence of rake angle, cutting feed and cutting depth on residual stresses in hard turning', Journal of Materials Processing Technology, Vol. 147, pp.181-184.
7. Grzesik, W. and Wanat, T. (2006) 'Surface finish generated in hard turning of quenched alloy steel parts using conventional and wiper ceramic inserts', International Journal of Machine Tools and Manufacture, Vol. 46, No. 15, pp.1988-1995.
8. Hua, J., Shivpuri, R., Cheng, X., Bedekar, V., Matsumoto, Y., Hashimoto, F. and Watkins, T.R. (2005) 'Effect of feed rate, workpiece hardness and cutting edge on subsurface residual stress in the hard turning of bearing steel using chamfer+hone cutting edge geometry', Materials Science and Engineering A, Vol. 394, pp.238-248.
9. Hua, J., Umbrello, D. and Shivpuri, R. (2006) 'Investigation of cutting conditions and cutting edge preparations for enhanced compressive subsurface residual stress in the hard turning of bearing steel', Journal of Materials Processing Technology, Vol. 171, pp.180-187.
10. Jawahir, I.S. and Van Luttervelt, C.A. (1993) 'Recent developments in chip control research and applications', Annals of the CIRP, Vol. 42, No. 2, pp.659-693.
11. Kusiak, A., Battaglia, J.L. and Rech, J. (2005) 'Tool coatings influence on the heat transfer in the tool during machining', Surface and Coatings Technology, Vol. 195, pp.29-40.
12. Liu, M., Takagi, J.I. and Tsukuda, A. (2004) 'Effect of nose radius and toolwear on residual stress distribution in hard turning', Journal of Materials Processing Technology, Vol. 150, pp.234-241.
13. Lu, J. (1996) Handbook of Measurement of Residual Stresses, The Fairmont Press, Inc.
14. Matsumoto, Y., Hashimoto, F. and Lahoti, G. (1999) 'Surface integrity generated by precision hard turning', Annals of the CIRP, Vol. 48, No. 1, pp.59-62.
15. More, A.S., Jiang, W., Brown, W.D. and Malshe, A.P. (2006) 'Tool wear and machining performance of c-BN/TiN coated carbide inserts and PCBN compact inserts in turning AISI4340 hardened steel', Journal of Materials Processing Technology, Vol. 180, pp.253-262.
16. Noyan, I.C. and Cohen, J.B. (1987) 'Residual stress. Measurement by diffraction and interpretation', Materials Research and Engineering Springer-Verlag.
17. Ordas, N. (2003) 'Residual stresses in tool steel due to hard-turning', Journal of Applied Crystallography, Vol. 36, pp.1135-1143.
18. Peiter, A. and Wern, H. (1987) 'Simultaneous X-ray measurements in-situ of tri-axial stresses, Poisson's ratio and the stress free lattice spacing', Strain, pp.103-107.
19. Poulachon, G. (1999) PhD Thesis, ENSAM (France).
20. Rech, J. (2006) 'Influence of cutting tool coatings on the tribological phenomena at the tool-chip interface in orthogonal dry cutting', Surface and Coatings Technology, Vol. 200, Nos. 16-17, pp.5132-5139.
21. Rech, J. and Moisan, A. (2003) 'Surface integrity in finish hard turning of case hardened steel', International Journal for Machine Tool and Manufacture, Vol. 43, No. 5, pp.543-550.
22. Rech, J., Valiorgue, F., Hamdi, H., Gilles, P. and Bergheau, J.M. (2006) 'A new approach for the modelling of residual stresses induced by turning of AISI316L stainless steels', International conference MMSS06, Krakow, Poland, 27-29 September 2006, ISBN 83 912887 73, pp.139-151.
23. Schwach, D.W. and Guo, Y.B. (2005) 'Feasibility of producing optimal surface integrity by process design in hard turning', Materials Science and Engineering A, Vol. 395, pp.116-123.
24. Thiele, J.D. and Melkote, S.N. (1999) 'The effect of tool edge geometry on workpiece sub-surface deformation and through-thickness residual stresses for hard turning of AISI52100', Transactions on NAMRI/SME Vol. 27, pp.135-140.
25. Thiele, J.D. and Melkote, S.N. (2000) 'Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel', Journal for Manufacturing Science Engineering Vol. 122, pp.642-649.
26. Wang, J.Y. and Liu, C.R. (1999) 'The effect of tool wear on the heat transfer, thermal damage and cutting mechanics in finish hard turning', Annals of the CIRP, Vol. 48, No. 1, pp.53-58.
27. Wern, H. (1991) 'Influence of measurement and evaluation parameters on stress distributions investigated by X-rays', Strain, pp.127-136.
28. Yan, H., Hua, J. and Shivpuri, R. (2007) 'Flow stress of AISIH13 die steel in hard machining', Materials and Design, Vol. 28, pp.272-277.
29. Zhou, J.M., Walter, H., Andersson, M. and Stahl, J.E. (2003) 'Effect of Chamfer angle on wear of PCBN cutting tool', International Journal of Machine Tools and Manufacture, Vol. 43, pp.301-305.