SCOPUS 정보 검색 플랫폼

Volumn 244, Issue 1-2, 2000, Pages 52-59

Experimental study on the performance of superfinish hard turned surfaces in rolling contact

Author keywords

Hard turning; Micro hardness; Repeatability and rolling contact fatigue life; Residual stress

Indexed keywords

FATIGUE OF MATERIALS; INTERFACES (MATERIALS); LIFE CYCLE; MICROHARDNESS; RESIDUAL STRESSES; STRESS ANALYSIS; SURFACE ROUGHNESS; TURNING;

HERTZIAN CONTACT STRESSES;

STEEL;

EXPERIMENTAL STUDY; FATIGUE LIFE ANALYSIS; HARDNESS; RESIDUAL STRESS; ROLLING CONTACT; SURFACE FINISHING;

EID: 0034253148 PISSN: 00431648 EISSN: None Source Type: Journal
DOI: 10.1016/S0043-1648(00)00438-5 Document Type: Article

Times cited : (81)

References (20)

1
- 0007630279
- Submitted 1996, granted 1999. Also pending in other countries
- US Patent 5878496
- Liu, C.R.¹ Mittal, S.²

2
- 0007700032
- Experimental study of surface roughness and residual stress in finish machining hardened steel
- (1996) M.S. Thesis, Purdue University
- Agha, S.R.¹

3
- 0007711981
- The effect of cutting conditions on rolling contact fatigue life of superfinish hard turned surfaces
- January
- (1999) Proceedings of the NSF Grantees Conference
- Agha, S.R.¹ Liu, C.R.²

4
- 0007709235
- On modeling the rolling contact fatigue life based on residual stress generated by superfinish hard turning
- January
- (2000) Proceedings of the NSF Design and Manufacturing Research Conference
- Agha, S.R.¹ Liu, C.R.²

5
- 0007662371
- The impact of cutting conditions on the rolling contact faigue life of super finish hard turned surfaces
- (1999) Proceedings of the 5th International Conference of Manufacturing Technology, Beijing, May
- Agha, S.R.¹ Liu, C.R.²

6
- 0004278919
- Wiley, New York
- (1993) Rolling Bearing Analysis
- Harris, T.A.¹

7
- 0001630376
- Machining hard materials with geometrically defined cutting edges-field of applications and limitations
- CIRP , vol.39 , Issue.1 , pp. 61-64
- Konig, W.¹ Klinger, M.² Link, R.³

8
- 0027245269
- Turning versus grinding - a comparison of surface integrity aspects and attainable accuracies
- (1993) CIRP , vol.42 , Issue.1 , pp. 39-43
- Konig, W.¹ Berktold, A.² Koch, K.-F.³

9
- 0017022402
- The mechanical state of the sublayer of a surface generated by chip-removal process. Part 1. Cutting with a sharp tool
- (1976) Trans. ASME, J. Eng. Ind. , vol.98 , pp. 1192-1201
- Liu, C.R.¹ Barash, M.M.²

10
- 0017025238
- The mechanical state of the sublayer of a surface generated by chip-removal process. Part 2. Cutting with a tool with flank wear
- (1976) Trans. ASME, J. Eng. Ind. , vol.98 , pp. 1202-1208
- Liu, C.R.¹ Barash, M.M.²

11
- 0007631394
- in: Paper presented at McGill Manufacturing Company and Timken Company, October
- (1989) Single-step Finishing
- Liu, C.R.¹

12
- 58149362506
- Single step super-finishing resulting in superior surface integrity
- (1995) J. Manufacturing Syst. , vol.14 , Issue.2 , pp. 124-133
- Liu, C.R.¹ Mittal, S.²

13
- 0030104216
- Single step super-finish hard machining, feasibility and feasible cutting conditions
- (1996) Robotics Comput. Integrated Manufacturing , vol.12 , Issue.1 , pp. 15-27
- Liu, C.R.¹ Mittal, S.²

14
- 0003339868
- Experimental study of the pre-stressing capability through residual stress generation in super-finishing machining of hardened steel
- (1997) Proceedings of the International Mechanical Engineering Congress
- Liu, C.R.¹ Agha, S.R.²

15
- 0032483161
- Optimal pre-stressing the surface of a component by superfinish hard turning for maximum fatigue life in rolling contact
- (1998) Wear , vol.219 , pp. 128-140
- Liu, C.R.¹ Mittal, S.²

16
- 0021563157
- Residual stress in the machined surface of hardened steel
- (1984) High Speed Machining ASN , pp. 193-204
- Matsumoto, Y.¹ Barash, M.M.² Liu, C.R.³

17
- 0032094389
- A method for modeling residual stresses in superfinish hard turning
- (1998) Wear , vol.218 , pp. 21-33
- Mittal, S.¹ Liu, C.R.²

18
- 0003631606
- Springer, Berlin
- (1987) Residual Stress
- Noyan, I.C.¹ Cohen, J.B.²

* 이 정보는 Elsevier사의 SCOPUS DB에서 KISTI가 분석하여 추출한 것입니다.