Rolling contact fatigue life of finish hard machined surfaces. Part 2. Experimental verification

Wear

Volumn 261, Issue 5-6, 2006, Pages 492-499

  Choi, Youngsik ^a   Liu, C Richard ^a  

^a SCHOOL OF INDUSTRIAL ENGINEERING   (United States)

Author keywords

Hard machining; Machining conditions; Micro hardness; Residual stress; Rolling contact fatigue; Testing

Indexed keywords

CRACK INITIATION; CRACK PROPAGATION; MATHEMATICAL MODELS; MICROHARDNESS; RESIDUAL STRESSES; STRESS CONCENTRATION;

HARD MACHINING; MACHINING CONDITIONS; ROLLING CONTACT FATIGUE; ROLLING CONTACT FATIGUE LIFE MODELS;

FATIGUE OF MATERIALS;

CRACK INITIATION; CRACK PROPAGATION; FATIGUE OF MATERIALS; MATHEMATICAL MODELS; MICROHARDNESS; RESIDUAL STRESSES; STRESS CONCENTRATION;

EID: 33747800050     PISSN: 00431648     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.wear.2005.12.003     Document Type: Article

References (23)

1. C.R. Liu, S.R. Agha, US Patent, submitted 2002, approved 2005, will be granted.
2. Abrão A.M., and Aspinwall D.K. The surface integrity of turned and ground hardened bearing steel. Wear 196 (1996) 279-284
3. Matsumoto Y., Barash M.M., and Liu C.R. Residual stress in the machined surface of hardened steel. High Speed Mach. (1984) 193-204
4. Matsumoto Y., Barash M.M., and Liu C.R. Effect of hardness on the surface integrity of AISI 4340 steel. J. Eng. Ind. 108 (1986) 169-175
5. Liu C.R., and Guo Y.B. Finite element analysis of the effect of sequential cuts and tool-chip friction on residual stresses in a machined layer. Int. J. Mech. Sci. 42 (2000) 1069-1089
6. S.R. Agha, Experimental study of surface roughness and residual stress in finish machining hardened steel, MS Thesis, Purdue University, 1996.
7. J. Shi, Prediction of thermal damage in superfinish hard machined surfaces, PhD Thesis, Purdue University, 2004.
8. S.R. Agha, Fatigue performance of superfinish hard turned surfaces in rolling contact, PhD Thesis, Purdue University, 2000.
9. Taguchi G. Taguchi on Robust Technology Development: Bringing Quality Engineering Upstream (1993), ASME Press pp. 85-113 (Chapter 5)
10. Noyan I.C., and Cohen J.B. Residual Stress: Measurement by Diffraction and Interpretation (1987), Springer-Verlag pp. 122-123 (Chapter 5)
11. Zhou R.S. Surface topography and fatigue life of rolling contact bearings. Tribol. Trans. 36 (1993) 329-340
12. Agha S.R., and Liu C.R. Experimental study on the performance of superfinish hard turned surfaces in rolling contact. Wear 244 (2000) 52-59
13. Jin X.Z., and Kang N.Z. A study on rolling bearing contact fatigue failure by macro-observation and micro-analysis. Proceedings of the International Conference on Wear of Materials. Denver, Colorado (1989) 205-213
14. Rich J.E.F., Battez A.H., and Cuervo D.G. Rolling contact fatigue in lubricated contacts. Tribol. Int. 36 (2003) 35-40
15. Hamrock B., and Dowson D. Isothermal elasto-hydrodynamic lubrication of point contacts-part III-fully flooded results. J. Lubric. Technol. 99 (1977) 264-276
16. Xie Q., Bayoumi E., and Kendall L.A. On tool wear and its effect on machined surface integrity. J. Mater. Shaping Technol. 8 (1990) 255-265
17. Fathailal M., Danai K., and Barber G. Effect of flank wear on the topography of machined surfaces. Tribol. Trans. 36 4 (1993) 693-699
18. Davies M.A., Chou Y., and Evans C.J. On chip morphology, tool wear, and cutting mechanics in finish hard turning. Ann. CIRP 45 1 (1996) 77-82
19. C.A. Moyer, H.P. Nixon, R.R. Bhatia, Tapered roller bearing performance for the 1990s, SAE Paper No. 881232, 1988.
20. Johnson K.L. Contact Mechanics (1985), Cambridge University Press, Cambridge pp. 84-106 (Chapter 4)
21. Lundberg G., and Palmgren A. Dynamic capacity of rolling bearings. Acta Polytech. Mech. Eng. Ser. 1 3 (1947)
22. Lundberg G., and Palmgren A. Dynamic capacity of rolling bearings. Acta Polytech. Mech. Eng. Ser. 2 4 (1952)
23. International Standards Organization, Rolling bearings-dynamic load ratings and rating life. Part 1. Calculation methods, International Standard 281/1-1977 (E).