Investigation of cutting conditions and cutting edge preparations for enhanced compressive subsurface residual stress in the hard turning of bearing steel

Journal of Materials Processing Technology

Volumn 171, Issue 2, 2006, Pages 180-187

  Hua, Jiang ^a   Umbrello, Domenico ^b   Shivpuri, Rajiv ^a  

^a OHIO STATE UNIVERSITY   (United States)

^b UNIVERSITY OF CALABRIA   (Italy)

Author keywords

FEM; Hard machining; Material modeling; Residual stresses

Indexed keywords

BEARINGS (MACHINE PARTS); CUTTING TOOLS; FINITE ELEMENT METHOD; INTERFACES (MATERIALS); MACHINING; RESIDUAL STRESSES; STEEL;

CUTTING EDGE PREPARATION; HARD MACHINING; MATERIAL MODELING;

METAL CUTTING;

EID: 30144441719     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2005.06.087     Document Type: Article

References (15)

1. Y. Matsumoto, M.M. Barash, and C.R. Liu Effect of hardness on the surface integrity of AISI 4340 Stel J. Eng. Ind. 108 3 1986 169 175
2. J.D. Thiele, S.N. Melkote, R.A. Peascoe, and T.R. Watkins Effect of cutting-edge geometry aned workpiece hardness on surface residual stresses in finish hard turning of AISI 2100 steel J. Manuf. Sci. Eng. 122 November 2000 642 649
3. J.D. Thiele, and S.N. Melkote The effect of tool edge geometry on workpiece sub-surface deformation and through-thickness residual stresses for hard turning of AISI 52100 steel Trans. NAMRI/SME 27 1999 135 140
4. P. Dahlman, F. Gunnberg, and M. Jacobson The influence of rake angle, cutting feed and cutting depth on residual stresses in hard turning J. Mater. Process. Technol. 147 2 2004 181 184
5. Y. Matsumoto, F. Hashimoto, and G. Lahoti Surface integrity generated by precision hard turning Ann. CIRP 48 1999 59 62
6. A.M. Abrao, and D.K. Aspinwall The surface integrity of turned and ground hardened bearing steel Wear 196 1996 279 284
7. S.R. Agha, and C.R. Liu Experimental study on the performance of superfinish hard turned surfaces in rolling contact Wear 244 2000 52 59
8. J. Hua, X. Cheng, V. Bedekar, R. Shivpuri, Y. Matsumoto, F. Hashimoto, and T.R. Watkins Effect of feed rate, workpiece hardness and cutting edge on subsurface residual stress in the hard turning of bearing steel using chamfer + hone cutting edge geometry Mater. Sci. Eng. A 394 2005 238 248
9. S. Mittal, and C.R. Liu A method of modeling residual stresses in superfinish hard turning Wear 218 1998 21 33
10. C.R. Liu, and S. Mittal Optimal pre-stressing the surface of a component by superfinish hard turning for maximum fatigue life in rolling contact Wear 219 1998 128 240
11. D. Umbrello, J. Hua, and R. Shivpuri Hardness based flow stress for numerical modelling of hard machining AISI 52100 bearing steel Mater. Sci. Eng. A 374 2004 90 100
12. S. Kobayashi, S.K. Oh, and T. Altan Metal Forming and The Finite-Element Method 1989 Oxford University Press, Inc.
13. Y.B. Guo, and C.R. Liu Mechanical properties of hardened AISI 52100 steel in hard machining processes ASME J. Manuf. Sci. Eng. 124 February 2002 1 9
14. K.D. Bouzakis, and N. Vidakis Superficial plastic response determination of hard isotropic materials using ball indentations and a FEM optimization technique Mater. Charact. 42 1 1999 1 12
15. P. Brozzo, B. De Luca, and R. Rendina A new method for the prediction of formability limit of metal sheet Proceedings of the 7th Biennial Conference of the International Deep Drawing Research Group 1972