Effect of tool nose radius and tool wear on residual stress distribution in hard turning of bearing steel

Journal of Materials Processing Technology

Volumn 150, Issue 3, 2004, Pages 234-241

  Liu, Meng ^a   Takagi, Jun Ichiro ^a   Tsukuda, Akira ^b  

^a YOKOHAMA NATIONAL UNIVERSITY   (Japan)

^b Kagawa Prefectural Industrial Technology Center   (Japan)

Author keywords

Bearing steel; CBN tool; Hard turning; Nose radius; Residual stress

Indexed keywords

MACHINING; RESIDUAL STRESSES; STEEL STRUCTURES; STRESS CONCENTRATION; TURNING; WEAR OF MATERIALS;

BEARING STEEL; HARD TURNING; NOSE RADIUS; TOOL WEAR;

TOOLS;

EID: 2942525845     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2004.02.038     Document Type: Article

References (31)

1. Tonshoff H.K., Arendt C., Ben Amor R. Cutting of hardened steel. Ann. CIRP. 49(2):2000;547-566.
2. Konig W., Komanduri R., Tonshoff H.K., Ackershott G. Machining of hardened materials. Ann. CIRP. 33(2):1984;417-427.
3. Konig W., Berktold A., Koch K.-F. Turning versus grinding - a comparison of surface integrity aspects and attainable accuracies. Ann. CIRP. 42:1993;39-43.
4. N. Narutaki, Y. Yamane, Tool wear and cutting temperature of CBN tool in machining of hardened steels, Ann. CIRP 28 (1) (1979) 23-28.
5. Hodgson T., Trendler P.H. Turning hardened tool steels with cubic boron nitride inserts. Ann. CIRP. 30(1):1981;63-66.
6. Konig W., Klinger M., Link R. Machining hard materials with geometrically defined cutting edges - field on applications and limitations. Ann. CIRP. 39(1):1990;61-64.
7. Liu C.R., Mittal S. Single-step superfinishing using hard turning resulting in superior surface integrity. J. Manuf. Syst. 14(2):1995;124-133.
8. Kishawy H.A., Elbestawi M.A. Effects of process parameters on material side flow during hard turning. Int. J. Mach. Tools Manuf. 39:1999;1017-1030.
9. Matsumoto Y., Hashimoto F., Lahoti G. Surface integrity generated by precision hard turning. Ann. CIRP. 48(1):1999;59-62.
10. Abrao A.M., Aspinwall D.K. The surface integrity of turned and ground hardened bearing steel. Wear. 196:1996;279-284.
11. EI-Wardany T.I., Kishawy H.A., Elbestawi M.A. Surface integrity of die material in high speed hard machining. Part 2. Microhardness variations and residual stresses. ASME J. Manuf. Sci. Eng. 122:2000;632-641.
12. Matsumoto Y., Barash M.M., Liu C.R. Effects of hardness on the surface integrity of AISI4340 steel. ASME J. Eng. Ind. 108:1986;169-175.
13. Wu D.W., Matsumoto Y. The effect of hardness on residual stress in orthogonal machining of AISI 4340 steel. ASME J. Eng. Ind. 112:1990;245-252.
14. Thiele J.D., Melkote S.N., Peascoe R.A., Watkins T.R. Effect of cutting edge geometry and workpiece hardness on surface residual stress in finish hard turning of AISI52100 steel. Manuf. Sci. Technol. ASME. 122:2000;642-649.
15. El-Wardany T.I., Kishawy H.A., Elbestawi M.A. Surface integrity of die material in high speed hard machining. Part 1. Micrographical analysis. ASME J. Manuf. Sci. Eng. 122:2000;620-631.
16. Agha S.R., Liu C.R. Experimental study on the performance of superfinish hard turned in rolling contact. Wear. 244:2000;52-59.
17. Liu C.R., Mittal S. Optimal pre-stressing the surface of a component by superfinish hard turning for maximum fatigue life in rolling contact. Wear. 219:1998;129-410.
18. Munoz-Escalona P., Cassier Z. Influence of the critical cutting speed on the surface finish of turned steel. Wear. 218:1998;103-109.
19. Jacobus K., Devor R.E., Kapoor S.G. Machining-introduced residual stress: experimental and modeling. ASME J. Manuf. Sci. Eng. 122:2000;20-31.
20. Thiele J.D., Melkote S.N. Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel. J. Mater. Process. Technol. 94:1999;216-226.
21. Thiele J.D., Melkote S.N., Peascoe R.A., Watkins T.R. Effect of cutting edge geometry and workpiece hardness on surface residual stress in finish hard turning of AISI52100 steel. Manuf. Sci. Technol. ASME. 122:2000;642-649.
22. Brinksmeier E., Cammett J.T., Konig W., Leskovar P., Tonshoff K. Residual stress-measurement and causes in machining processes. Ann. CIRP. 31:1982;491-510.
23. Liu C.R., Mittal S. Single-step superfinish hard machining: feasibility and feasible cutting conditions. Robot. Comput.-Integr. Manuf. 12:1996;15-27.
24. Mitsubishi Material Co. Ltd., Japan. http://www.mitsubishicarbide.com. mmus/en/index.htm.
25. Nakayama K., Arai M., Kanda T. Machining characteristics of hard materials. Ann. CIRP. 37(1):1988;89-92.
26. E. Brinksmeier, J.T. Cammett, W. Konig, P. Leskovar, J. Peters, H.K. Tonshoff, Residual stresses - measurement and causes in the machining process, Ann. CIRP 31 (2) (1982) 491-510.
27. El-Helieby S.O.A., Rowe G.W. A quantitative comparison between residual stresses and fatigue properties of surface-ground bearing steel (EN31). Wear. 58:1980;155-172.
28. Rowe W.B., Morgan M.N., Black S.C.E., Mills B. A simplified approach to control of thermal damage in grinding. Ann. CIRP. 45(1):1996;299-302.
29. Chen X., Rowe W.B., McCormack D.F. Analysis of the transitional temperature for tensile residual stress in grinding. J. Mater. Process. Technol. 107:2000;216-221.
30. Matsumoto Y., Barash M.M., Liu C.R. Cutting mechanisms during machining of hardened steels. Mater. Sci. Technol. 3:1987;299-305.
31. Barash M.M., Liu C.R. The mechanical state of the sublayer of a surface generated by chipremoval process. J. Eng. Ind. 98(4):1976;1192-1208.