Fabrication of an LCD light guide plate using closed-die hot embossing

Journal of Micromechanics and Microengineering

Volumn 18, Issue 3, 2008, Pages

  Wu, Cheng Hsien ^a   Lu, Chien Hung ^b  

^a NATIONAL KAOHSIUNG UNIVERSITY OF APPLIED SCIENCES   (Taiwan)

^b DA YEH UNIVERSITY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

INJECTION MOLDING; MICROSTRUCTURE; OPTICAL ANISOTROPY; POLYMETHYL METHACRYLATES;

CLOSED-DIE HOT EMBOSSING; LIGHT GUIDE PLATE;

LIQUID CRYSTAL DISPLAYS;

EID: 42549123521     PISSN: 09601317     EISSN: 13616439     Source Type: Journal    
DOI: 10.1088/0960-1317/18/3/035006     Document Type: Article

References (16)

1. Feng D, Jin G, Yan Y and Fan S 2004 High quality light guide plates that can control the illumination angle based on microprism structures Appl. Phys. Lett. 85 6016-8
2. Yao D and Kim B 2002 Simulation of the filling process in micro channels for polymeric materials J. Micromech. Microeng. 12 604-10
3. Wimberger-Friedl R 2000 Injection molding of sub-νm grating optical elements J. Injection Molding Technol. 4 78-83
4. Yao D and Kim B 2002 Injection molding high aspect ratio microfeatures J. Injection Molding Technol. 6 11-7
5. Wu C-H and Chen W-S 2006 Injection molding and injection compression molding of three-beam grating of DVD pickup lens Sensors Actuators A 125 367-75
6. Heckele M, Bacher W and Müller K D 1998 Hot embossing-the molding technique for plastic microstructures Microsyst. Technol. 4 122-4
7. Rötting O, Röpke W, Becker H and Gärtner C 2002 Polymer microfabrication technologies Microsyst. Technol. 8 32-6
8. Wu C H and Kuo H C 2007 Parametric study of injection molding and hot embossing in polymer microfabrication J. Mech. Sci. Technol. 21 1338-43
9. Ong N S, Koh Y H and Fu Y Q 2002 Microlens array produced using hot embossing process Microelectron. Eng. 60 365-79
10. Schift H, David C, Gabriel J, Gobrecht J, Heyderman L J, Kaiser W, Koppel S and Scadella L 2000 Nanoreplication in polymers using hot embossing and injection molding Microelectron. Eng. 53 171-4
11. Chen S C, Chen Y C and Cheng N T 1998 Simulation of injection-compression mold-filling process Int. Commun. Heat Mass Transf. 25 907-17
12. Chang T C and Faison E 2001 Shrinkage behavior and optimization of injection molded parts studied by the Taguchi method Polym. Eng. Sci. 41 703-10
13. Huang M C and Tai C C 2001 The effective factors in the warpage problem of an injection-molded part with a thin shell feature J. Mater. Process. Technol. 110 1-9
14. Becker H and Heim U 2000 Hot embossing as a method for the fabrication of polymer high aspect ratio structures Sensors Actuators 83 130-5
15. Ong N S, Koh Y H and Fu Y Q 2002 Microlens array produced using hot embossing process Microelectron. Eng. 60 365-79
16. Mekaru H, Yamada T, Yan S and Hattori T 2004 Microfabrication by hot embossing and injection molding at LASTI Microsyst. Technol. 10 682-8