Review of dynamic issues in micro-end-milling

International Journal of Advanced Manufacturing Technology

Volumn 31, Issue 9-10, 2007, Pages 897-904

  Miao, J C ^a   Chen, G L ^a   Lai, X M ^a   Li, H T ^a   Li, C F ^a  

^a SHANGHAI JIAO TONG UNIVERSITY   (China)

Author keywords

Chip formation; Micro meso mechanical manufacturing (M4); Process stability; Size effect; Vibration

Indexed keywords

MACHINE VIBRATIONS; MICROELECTROMECHANICAL DEVICES; MICROMACHINING; MICROPROCESSOR CHIPS; MILLING MACHINES; THREE DIMENSIONAL;

CHIP FORMATION; MESO MECHANICAL MANUFACTURING; MICRO-END-MILLING MACHINING; PROCESS STABILITY;

MILLING (MACHINING);

EID: 33846220023     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-005-0276-6     Document Type: Article

References (48)

1. Kawahara N, Suto T, Hirano T, Ishikawa Y, Kitahara T, Oyama N, Ataka T (1997) Microfactories: new applications of micromachine technology to the manufacture of small products. Res J Microsyst Technol 3(2):37-41
2. MEL, AIST/MITI, Japan (1999) Micro machines. Annual Report of the Mechanical Engineering Laboratory, vol 21. Home page at: http://www.aist.go.jp/ MEL/
3. Sun YZ, Liang YC, Cheng K (2004) Micro-scale and meso-scale mechanical manufacturing. Chin J Mech Eng 40:1-6
4. Bang YB, Lee KY, Oh SY (2004) 5-axis micro milling machine for machining micro parts. Adv Manuf Technol 25:888-894
5. Lu Z, Yoneyama T (1999) Micro cutting in the micro lathe turning system. Int J Mach Tools Manuf 39:1171-1183
6. Yonyama T, Lu ZN (1998) Trial construction of micro turning system. J JSPE 64(4):598-602
7. Kitahara T, Ishikawa Y, Terada T, Nakajima N, Furuta K (1996) Development of micro-lathe. J Mech Eng Lab 50(5):117-123
8. Je T, Lee J, Choi D, Lee E, Shin B, Wang K (2004) A study of the micro pole structure fabrication and application technology by micro end-milling process. Key Eng Mater 257(258):453-458
9. Spath D, Huntrup V (1999) Micro-milling of steel for mold manufacturing influence of material, tools and process parameters. In: Proceedings of the 1st International Conference and General Meeting of the European Society for Precision Engineering and Nanotechnology (EUSPEN), Bremen, Germany, May/June 1999, pp 203-206
10. Rahman M, Kumar AS, Prakash JRS (2001) Micro milling of pure copper, J Mater Process Technol 116:39-43
11. Schaller T, Bohn L, Mayer J, Schubert K (1999) Microstructure grooves with a width of less than 50 urn cut with ground hard metal micro end mills. Precis Eng 23(4):229-235
12. Friedrich C, Coane P, Goettert J, Gopinathin N (1998) Direct fabrication of deep x-ray lithography masks by micromechanical milling. Precis Eng 22(3):164-173
13. Tansel I, Rodriguez O, Trujillo M, Paz E, Li W (1998) Microend-milling: I. Wear and breakage. Int J Mach Tools Manuf 38 (12):1419-1436
14. Tansel IN, Arkan TT, Bao WY, Mahendrakar N, Shisler B, Smith D, McCool M (2000) Tool wear estimation in micromachining. Part II: neural-network-based periodic inspector for nonmetals. Int J Mach Tools Manuf 40:609-620
15. Bao WY, Tansel IN (2000) Modeling micro-end-milling operations. Part III: influence of tool wear. Int J Mach Tools Manuf 40(15):2193-2211
16. Tansel I, Trujillo M, Nedbouyan A, Velez C, Bao WY, Arkan TT, Tansel B (1998) micro-end-milling. III. Wear estimation and tool breakage using acoustic emission signals. Int J Mach Tools Manuf 38:1349-1366
17. Friedrich CR, Vasile MJ (2001) development of the micromilling process for high-aspect-ratio microstructures. J Microelectromech Syst 5(1):33-38
18. Vasile MJ, Friedrich CR, Kikkeri B, Mcelhannpn R (1996) Micrometer-scale machining: tool fabrication and initial results. Precis Eng 19(2-3):180-186
19. Takeuchi Y, Kato K., Kawakita S, Sata T (1993) Generation of sculptured surfaces by means of an ultra-precision milling machine. Annals CIRP 42:611-614
20. Damazo BN, Davies MA, Dutterer BS, Kennedy MD (1999) A summary of micro-milling studies. In: Proceedings of the 1st International Conference and General Meeting of the European Society for Precision Engineering and Nanotechnology (EU-SPEN), Bremen, Germany, May/June 1999, pp 322-325
21. Friedrich CR, Kikkeri B (1995) Rapid fabrication of molds by mechanical micromilling: process development. Proc SPIE 2640:161-171
22. Lee K, Ahn SH, Dornfeld DA, Wright PK (2001) The effect of run-out on design for manufacturing in micro-machining process. In: Proceedings of the ASME International Mechanical Engineering Congress and Exposition (IMECHE 2001), ASME Manufacturing Engineering Division, New York, November 2001
23. Miyaguchi T, Masuda M, Takeoka E, Iwabe H (2001) Effect of tool stiffness upon tool wear in high spindle speed milling using small ball end mill. Precis Eng 25(2):145-154
24. Bao WY, Tansel IN (2000) Modeling micro-end-milling operations. Part II: tool run-out, Int J Mach Tools Manuf 40 (15):2175-2192
25. Bao WY, Tansel IN (2000) Modeling micro-end-milling operations. Part I: analytical cutting force model. Int J Mach Tools Manuf 40(15):2155-2173
26. Lee K, Dornfold DA, Kapoor SG (2002) An experimental study on burr formation in micro milling aluminum and copper. Trans NAMRI/SME 30:255-262
27. Weule H, Hüntrup V, Tritschler H (2001) Micro-cutting of steel to meet new requirements in miniaturization. Annals CIRP 50:61-64
28. Löhe D, Peishl A, Schulze V, Spath, Trischler H (2000) Microcutting of steels - interaction of material properties and process parameters. In: Proceedings of the Micro TEC 2000 conference, Hannover, Germany, September 2000, vol 55, pp 195-204
29. Peichl A, Hüntrup V, Schulze V, Löhe D, Spath D (2000) Einfluss des Warmebehandlungszustands auf die mikrozerspanbarkeit von Stahlen. Htarterei Technische Mitteilungen 55:195-204
30. Shawky AM, Elbestawi MA (1997) An enhanced dynamic model in turning including the effect of ploughing forces. J Manuf Sci Eng - Trans ASME 119(1):10-20
31. Ohbuchi Y, Obikawa T (2003) Finite element modeling of chip formation in the domain of negative rake angle cutting. J Manuf Sci Eng-Trans ASME 125(3):324-332
32. Yuan ZJ, Ceng L, Dong S (1997) Ultraprecision machining of SiCw/Al composites. Annals CIRP 42:107-109
33. Chan KC, Cheung CF, Ramesh MV, Lee WB, To S (2001) A theoretical and experimental investigation of surface generation in diamond turning of an Al6061/SiCp metal matrix composite. Int J Sci 43(9):2047-2068
34. Katayama S, Toda M, Hashimura M (1997) Growth model of built-up edge based on inhomogeneities in microstructure of steel. Int J Jpn Soc Prec Eng 31:15-20
35. Voigt RC, Marana RO, Cohen PH (1999) Machinability of gray iron - mechanics of chip formation. Int J Cast Metal Res 11 (5):567-572
36. Zhu H, Zhao J (1983) Micro manufacturing technology. Chinese Science Publishing Company
37. Kim CJ (2004) Mechanisms of chip formation and cutting dynamics in the micro-scale milling process. PhD dissertation, University of Michigan, Michigan
38. Kim CJ, Mayor JR, Ni J (2004) A static model of chip formation in microscale milling. J Manuf Sci Eng - Trans ASME 126(4):710-718
39. Wu DW (1998) A new approach of formulating the transfer function for dynamic cutting processes. J Eng Ind - Trans ASME 111:37-47
40. Endres WJ, Devor RE, Kapoor SG (1995) A dual-mechanism approach to the prediction of machining forces. Part I: model development. J Eng Ind-Trans ASME 117:526-533
41. Endres WJ, Devor RE, Kapoor SG (1995) A dual-mechanism approach to the prediction of machining forces. Part II: calibration and vibration. J Eng Ind - Trans ASME 117:534-541
42. Montgomery D, Altintas Y (1991) Mechanism of cutting force and surface generation in dynamic milling. J Eng Ind - Trans ASME 113:160-168
43. Liu X, Jun MBG, DeVor RE, Kapoor SG (2004) Cutting mechanisms and their influence on dynamic forces, vibrations and stability in micro-end-milling. In: Proceedings of the ASME International Mechanical Engineering Congress and Exposition (IMECHE 2004), ASME Manufacturing Engineering Division, Anaheim, California, November 2004
44. Sutherland JW, DeVor RE (1986) Improved method for cutting force and surface error prediction in flexible end milling systems. J Eng Ind-Trans ASME 108:269-279
45. Vogler MP, DeVor RE, Kapoor SG (2003) Microstructure-level force prediction model for micro-milling of multi-phase materials. J Eng Ind-Trans ASME 125(2):202-209
46. Yuan ZJ, Zhou M, Dong S (1996) Effect of diamond tool sharpness on minimum cutting thickness and cutting surface integrity in ultraprecision machining. J Mater Process Technol 62(4):327-330
47. Shimada S, Ikawa N, Tanaka H, Ohmuri G, Uchikoshi J, Yoshinaga H (1993) Feasibility study on ultimate accuracy in microcutting using molecular dynamics simulation. Annals CIRP 42(1):91-94
48. Shimada S, Ikawa N, Ohmuri G, Tanaka H, Uchikoshi J (1992) Molecular dynamic analysis as compared with experimental results of micromachining. Annals CIRP 41(1):117-120