Green cooling of high performance microprocessors: Parametric study between flow boiling and water cooling

Journal of Thermal Science and Engineering Applications

Volumn 3, Issue 4, 2011, Pages 1-12

  Olivier, Jonathan A ^a   Marcinichen, Jackson B ^a   Bruch, Arnaud ^a   Thome, John ^a  

^a EPFL   (Switzerland)

Author keywords

Data centers; Electronics cooling; Energy; Exergy; Flow boiling; Green; Microevaporators; Refrigerant

Indexed keywords

EID: 84970898667     PISSN: 19485085     EISSN: 19485093     Source Type: Journal    
DOI: 10.1115/1.4004435     Document Type: Article

References (59)

1. EPA, 2007, Report to Congress on Server and Data Center Energy Efficiency Public Law 109-431, U.S. Environmental Protection Agency.
2. Larson, J. B., 2009, America’s Energy Security Trust Fund Act of 2009, in H.R. 1337.
3. Koomy, J. G., 2007, Estimating Regional Power Consumption by Servers: A Technical Note, Lawrence Berkeley National Laboratory, Oakland, CA.
4. IBM, 2007, IBM Unveils Plan to Combat Data Center Energy Crisis; Allocates $1 Billion to Advance “Green” Technology and Services, http://www-03.ibm.-com/press/us/en/pressrelease/21524.wss
5. Leonard, P. L., and Phillips, A. L, 2005, “The Thermal Bus Opportunity—A Quantum Leap in Data Center Cooling Potential,” ASHRAE Transactions, Denver, CO.
6. Saini, M., and Webb, R. L., 2003, “Heat Rejection Limits of Air Cooled Plane Fin Heat Sinks for Computer Cooling,” IEEE Trans. Compon. Packag. Tech- nol., 26(1), pp. 71-79.
7. Ellsworth, M. J., Jr., and Simons, R. E., 2005, “High Powered Chip Cooling— Air and Beyond,” Electron. Cooling, 11(3), pp. 14-22.
8. CMOSAIC, 2010, “3D Stacked Architectures with Interlayer Cooling,” http://esl.epfl.ch/page78902-en.html
9. Brunschwiler, T., Smith, B., Ruetsche, E., and Michel, B., 2009, “Toward ZeroEmission Data Centers Through Direct Reuse of Thermal Energy,” IBM J. Res. Dev., 53(3), pp. 11:1-11:13.
10. Chu, R. C., Simons, R. E., Ellsworth, M. J., Schmidt, R. R., and Cozzolino, V., 2004, “Review of Cooling Technologies for Computer Products,” IEEE Trans. Device Mater. Reliability, 4(4), pp. 568-585.
11. Agostini, B., Fabbri, M., Park, J. E., Wojtan, L., Thome, J. R., and Michel, B., 2007, “State-of-the-Art of High Heat Flux Cooling Technologies,” Heat Transfer Eng., 28, pp. 258-281.
12. Celata, G. P., Cumo, M., Guglielmi, M., and Zummo, G., 2002, “Experimental Investigation of Hydraulic and Single-Phase Heat Transfer in 0.130-mm Capillary Tube,” Nanoscale Microscale Thermophys. Eng., 6, pp. 85-97.
13. Celata, G. P., Morini, G. L., Marconi, V., McPhail, S. J., and Zummo, G., 2006, “Using Viscous Heating to Determine the Friction Factor in Microchannels— An Experimental Validation,” Exp. Therm. Fluid Sci., 30, pp. 725-731.
14. Celata, G. P., Cumo, M., McPhail, S. J., and Zummo, G., 2006, “Characterization of Fluid Dynamic Behaviour and Channel Wall Effects in Microtube,” Int. J. Heat Fluid Flow, 27, pp. 135-143.
15. Celata, G. P., Cumo, M., Marconi, V., McPhail, S. J., and Zummo, G., 2006, “Microtube Liquid Single-Phase Heat Transfer in Laminar Flow,” Int. J. Heat Mass Transfer, 49, pp. 3538-3546.
16. Tuckerman, D. B., and Pease, R. F. W., 1981, “High-Performance Heat Sinking for VLSI,” IEEE Electron. Device Lett., EDL-2(2), pp. 126-129.
17. Colgan, E. G., Furman, B., Gaynes, M., Graham, W. S., LaBianca, N. C., Magerlein, J. H., Polastre, R. J., Rothwell, M. B., Bezama, R. J., Choudhary, R., Marston, K. C., Toy, H., Wakil, J., Zitz, J. A., and Schmidt, R. R., 2007, “A Practical Implementation of Silicon Microchannel Coolers for High Power Chips,” IEEE Trans. Compon. Packag. Technol., 30(2), pp. 218-225.
18. Colgan, E. G., Furman, B., Gaynes, M., LaBianca, N. C., Magerlein, J. H., Polastre, R. J., Bezama, R. J., Marston, K. C., and Schmidt, R. R., 2007, “High Performance and Subambient Silicon Microchannel Cooling,” ASME J. Heat Transfer, 129, pp. 1046-1051.
19. Ganapati, P., 2009, “Water-Cooled Supercomputer Doubles as Dorm Space Heater,” available from: http://www.wired.com/gadgetlab/2009/06/ibm- supercomputer/
20. Kandlikar, S. G., 2010, “Scale Effects on Flow Boiling Heat Transfer in Microchannels: A Fundamental Perspective,” Int. J. Therm. Sci., 49(7), pp. 1073-1085.
21. Kandlikar, S. G., and Balasubramanian, P., 2004, “An Extension of the Flow Boiling Correlation to Transition, Laminar, and Deep Laminar Flows in Minichannels and Microchannels,” Heat Transfer Eng., 25(3), pp. 86-93.
22. Kandlikar, S. G., 2004, “Heat Transfer Mechanisms During Flow Boiling in Microchannels,” ASME J. Heat Transfer, 126(1), pp. 8-17.
23. Celata, G. P., Saha, S. K., Zummo, G., and Dossevi, D., 2010, “Heat Transfer Characteristics of Flow Boiling in a Single Horizontal Microchannel,” Int. J. Therm. Sci., 49(7), pp. 1086-1094.
24. Bertsch, S. S., Groll, E. A., and Garimella, S. V., 2008, “Refrigerant Flow Boiling Heat Transfer in Parallel Microchannels as a Function of Local Vapor Quality,” Int. J. Heat Mass Transfer, 51(19-20), pp. 4775-4787.
25. Harirchian, T., and Garimella, S. V., 2008, “Microchannel Size Effects on Local Flow Boiling Heat Transfer to a Dielectric Fluid,” Int. J. Heat Mass Transfer, 51, pp. 3724-3735.
26. Lee, P. S., and Garimella, S. V., 2008, “Saturated Flow Boiling Heat Transfer and Pressure Drop in Silicon Microchannel Arrays,” Int. J. Heat Mass Transfer, 51(3-4), pp. 789-806.
27. Liu, D., Lee, P. S., and Garimella, S. V., 2005, “Prediction of the Onset of Nucleate Boiling in Microchannel Flow,” Int. Commun. Heat Mass Transfer, 48(25-26), pp. 5134-5149.
28. Bergles, A. E., and Kandlikar, S. G., 2005, “On the Nature of Critical Heat Flux in Microchannels,” ASME J. Heat Transfer, 127, pp. 101-107.
29. Wang, G., Cheng, P., and Bergles, A. E., 2008, “Effects of Inlet/Outlet Configurations on Flow Boiling Instability in Parallel Microchannels,” Int. J. Heat Mass Transfer, 51(9-10), pp. 2267-2281.
30. Thome, J. R., Dupont, V., and Jacobi, A. M., 2004, “Heat Transfer Model for Evaporation in Microchannels. Part I: Presentation of the Model,” Int. J. Heat Mass Transfer, 47, pp. 3375-3385.
31. Revellin, R., and Thome, J. R., 2008, “An Analytical Model for the Prediction of the Critical Heat Flux in Heated Microchannels,” Int. J. Heat Mass Transfer, 51, pp. 1216-1225.
32. Park, J. E., Thome, J. R., and Michel, B., 2009, “Effect of Inlet Orifice on Saturated CHF and Flow Visualization in Multi-Microchannel Heat Sinks,” Twenty-Fifth Annual Ieee Semiconductor Thermal Measurement and Management Symposium, pp. 1-8.
33. Costa-Patry, E., Olivier, J. A., and Thome, J. R., 2010, “Hot-Spot Effects on Two-Phase Flow of R245fain 85m-Wide Multi-Microchannels,” 16th International Workshop on Thermal Investigations of IC’s and Systems, Barcelona, Spain.
34. Zhang, T., Peles, Y., Wen, J. T., Tong, T., Chang, J., Prasher, R., and Jensen, M.K., 2010, “Analysis and Active Control of Pressure-Drop Flow Instabilities in Boiling Microchannel Systems,” Int. J. Heat Mass Transfer, 52, pp. 2347-2360.
35. Zhang, T., Wen, J. T., Peles, Y., Catano, J., Zhou, R., and Jensen, M. K., 2010, “Two-Phase Refrigerant Flow Instability Analysis and Active Control in Transient Electronics Cooling Systems,” Int. J. Multiphase Flow, 37(1), pp. 84-97.
36. Park, J. E., 2008, “Critical Heat Flux in Multi-Microchannel Copper Elements With Low Pressure Refrigerants,” Ph.D. thesis, Ecole Polytechnique Federale de Lausanne, Switzerland.
37. Madhour, Y., Olivier, J. A., Costa-Patry, E., Paredes, S., Michel, B., and Thome, J. R., 2011, “Flow Boiling of R134a in a Multi-Microchannel Heat Sink With Hotspot Heaters for Energy-Efficient Microelectronic CPU Cooling Applications,” IEEE Trans. Compon. Packag. Technol., 1(6), pp. 873-883.
38. Lemmon, E., Huber, M., and McLinden, M., 2007, NIST Standard Reference Database 23: Reference Fluid Thermodynamic and Transport Properties- REFPROP, S.R.D. National Institute of Standards and Technology and Program, Gaithersburg, MD.
39. Dupont, V., Thome, J. R., and Jacobi, A. M., 2004, “Heat Transfer Model for Evaporation in Microchannels. Part II: Comparison With the Database,” Int. J. Heat Mass Transfer, 47(14-16), pp. 3387-3401.
40. Cioncolini, A., Thome, J. R., and Lombardi, C., 2009, “Unified Macro-to- Microscale Method to Predict Two-Phase Frictional Pressure Drops of Annular Flows,” Int. J. Multiphase Flow, 35, pp. 1138-1148.
41. Müller-Steinhagen, H., and Heck, K., 1986, “A Simple Friction Pressure Drop Correlation for Two-Phase Flow in Pipes,” Chem. Eng. Prog., 20, pp. 297-308.
42. Ong, C. L., 2010, “Macro-to-Microchannel Transition in Two-Phase Flow and Evaporation,” Ph.D. thesis, Ecole Polytechnique Federale de Lausanne, Switzerland.
43. Ribatski, G., Wojtan, L., and Thome, J. R., 2006, “An Analysis of Experimental Data and Prediction Methods for Two-Phase Frictional Pressure Drop and flow Boiling Heat Transfer in Micro-Scale Channels,” Exp. Therm. Fluid Sci., 31, pp. 1-19.
44. Shah, R. K., and London, A. L., 1978, Laminar Flow Forced Convection in Ducts, Academic, New York.
45. Thome, J. R., 2009, Engineering Data Book III, Wolverine Tube, Inc., Huntsville, AL.
46. Montreal Protocol, 2000, The Montreal Protocol on Substances that Deplete the Ozone Layer. http://ozone.unep.org/Publications/MP_Handbook/Section_1.1_ The_Montreal_Protocol/
47. Kyoto Protocol, 1998, United Nations Framework Convention on Climate Change. http://www.unfccc.int
48. Nielsen, O. J., Javadi, M. S., Sulbaek, M. P., Hurley, M. D., Wallington, T. J., and Singh, R., 2007, “Atmospheric Chemistry of CT3CF=CH2: Kinetics and Mechanisms of Gas-Phase Reactions With Cl Atoms, OH Radicals, and O3,” Chem. Phys. Lett., 439, pp. 18-22.
49. Sondergaard, R., Nielsen, O. J., Hurley, M. D., Wallington, T. J., and Singh, R., 2007, “Atmospheric Chemistry of Trans-CF3CH=CHF: Kinetics of the GasPhase Reactions With Cl Atoms, OH Radicals, and O3,” Chem. Phys. Lett., 443, pp. 199-204.
50. Brown, J. S., Zilio, C., and Cavallini, A., 2010, “Thermodynamic Properties of Eight Fluorinated Olefins,” Int. J. Refrigeration, 33, pp. 235-241.
51. Agostini, B., Revellin, R., Thome, J. R., Fabbri, M., Michel, B., Calmi, D., and Kloter, U., 2008, “High Heat Flux Flow Boiling in Silicon Multi-Microchan- nels—Part III: Saturated Critical Heat Flux of R236fa and Two-Phase Pressure Drops,” Int. J. Heat Mass Transfer, 51(21-22), pp. 5426-5442.
52. Olivier, J. A., Marcinichen, J. B., and Thome, J. R., 2010, “Two-Phase Cooling of Datacenters: Reduction in Energy Costs and Improved Efficiencies,” 13th Brazilian Congress of Thermal Sciences and Engineering—ENCIT2010, Uber- landia, MG, Brazil.
53. Moran, M. J., Howard, I., and Shapiro, N., eds., 2010, Fundamentals of Engineering Thermodynamics, 6th ed., John Wiley & Sons, New York, pp. 1725.
54. Rosen, M. A., Dincer, I., and Kanoglu, M., 2008, “Role of Exergy in Increasing Efficiency and Sustainability and Reducing Environmental Impact,” Energy Policy, 36, pp. 128-137.
55. Karajgikar, S., Agonafer, D., Ghose, K., Sammakia, B., Amon, C., and Refai- Ahmed, G., 2010, “Multi-Objective Optimization to Improve Both Thermal and Device Performance of a Nonuniformly Powered Micro-Architecture,” ASME J. Electron. Packag., 132, pp. 81-87.
56. Bar-Cohen, A., Kraus, A. D., and Davidson, S. F., 1983, “Thermal Frontiers in the Design and Packaging of Microelectronic Equipment,” Mech. Eng., 105(6), pp. 53-59.
57. Agostini, B., and Thome, J. R., 2005, “Comparison of an Extented Database for Flow Boiling Heat Transfer Coefficients in Multi-Microchannels Elements With the Three-Zone Model,” ECI Heat Transfer and Fluid Flow in Microscale, Castelvecchio Pascoli, Italy.
58. Ong, C. L., and Thome, J. R., 2011, “Macro-to-Microchannel Transition in Two-Phase Flow: Part 2—Flow Boiling Heat Transfer and Critical Heat Flux,” Exp. Therm. Fluid Sci., 35(6), pp. 873—886
59. 041003-12/Vol. 3, DECEMBER 2011 Transactions of the ASME