Predicting auto-ignition characteristics of RCCI combustion using a multi-zone model

International Journal of Automotive Technology

Volumn 14, Issue 5, 2013, Pages 693-699

  Eguz U ^a   Maes, N C J ^a   Leermakers, C A J ^a   Somers, L M T ^a   Goey, L P H De ^a  

^a EINDHOVEN UNIVERSITY OF TECHNOLOGY   (Netherlands)

Author keywords

Detailed chemistry; Multi zone modeling; Reactivity controlled compression ignition

Indexed keywords

COMBUSTION PHASING; COMBUSTION SIMULATIONS; COMPRESSION IGNITION; DETAILED CHEMISTRY; DETAILED REACTION MECHANISMS; EMISSION STANDARD; IGNITION CHARACTERISTICS; MULTI-ZONE MODELS;

BLENDING; DIESEL FUELS; FUELS; GASOLINE;

IGNITION;

EID: 84884570418     PISSN: 12299138     EISSN: None     Source Type: Journal    
DOI: 10.1007/s12239-013-0075-2     Document Type: Article

References (17)

1. Andrae, J. C. G., Brinck, T. and Kalghatgi, G. T. (2008). HCCI experiments with toluene reference fuels modeled by a semi-detailed chemical kinetic model. Combustion and Flame, 155, 696-712.
2. Egüz, U., Somers, L. M. T., Leermakers, C. A. J. and de Goey, L. P. H. (2010). Multi-zone modeling of PCCI combustion. Int. J. Vehicle Design, 55, 76-90.
3. Egüz, U., Ayyapureddi, S., Bekdemir, C., Somers, L. M. T. and de Goey, L. P. H. (2012). Modeling fuel spray autoignition using the FGM approach: Effect of tabulation method. SAE Paper No. 2012-01-0157.
4. Hohenberg, G. F. (1979). Advanced approaches for heat transfer calculations. SAE Paper No. 790825.
5. Komninos, N. P. (2009). Assessing the effect of mass transfer on the formation of HC and CO emissions in HCCI engines, using a multi-zone model. Energy Conversion and Management, 50, 1192-1201.
6. Leermakers, C., van den Berge, B., Luijten, C., Somers, L., de Goey, L. P. H. and Albrecht, B. A. (2011). Gasolinediesel dual fuel: Effect of injection timing and fuel balance. SAE Paper No. 2011-01-2437.
7. Maiboom, A., Tauzia, X., Shah, S. R. and Hetet, J. F. (2009). New phenomenological six-zone combustion model for direct-injection diesel engines. Energy & Fuels, 23, 690-703.
8. Manente, V., Johansson, B., Tunestal, P. and Cannella, W. (2010a). Influence of inlet pressure, EGR, combustion phasing, speed and pilot ratio on high load gasoline partially premixed combustion. SAE Paper No. 2010-01-1471.
9. Manente, V., Tunestal, P., Johansson, B. and Cannella, W. (2010b). Effects of ethanol and different type of gasoline fuels on partially premixed combustion from low to high load. SAE Paper No. 2010-01-0871.
10. Nobakht, A. Y., Saray, R. K. and Rahimi, A. (2011). A parametric study on natural gas fueled HCCI combustion engine using a multi-zone combustion model. Fuel, 90, 1508-1514.
11. Ogink, R. and Golovitchev, V. (2005). Gasoline HCCI modeling: An engine cycle simulation code with a multizone combustion model. SAE Paper No. 2002-01-1745.
12. Poetsch, C., Ofner, H. and Schutting, E. (2011). Assessment of a multi zone combustion model for analysis and prediction of CI engine combustion and emissions. SAE Paper No. 2011-01-1439.
13. Rakopoulos, C. D., Michos, C. N. and Giakoumis, E. G. (2008). Availability analysis of a syngas fueled spark ignition engine using a multi-zone combustion model. Energy, 33, 1378-1398.
14. Sahin, Z. and Durgun, O. (2008). Multi-zone combustion modeling for the prediction of diesel engine cycles and engine performance parameters. Applied Thermal Engineering, 28, 2245-2256.
15. Somers, L. M. T., Evlampiev, A. E. and de Goey, L. P. H. (2007). Modelling auto-ignition of automotive fuels using detailed mechanisms. Proc. Combustion Institute.
16. van Oijen, J. A. and De Goey, L. P. H. (2004). A numerical study of confined triple flames using a flamelet-generated manifold. Combustion Theory Modelling, 8, 141-163.
17. Xu, H., Liu, M., Gharahbaghi, S., Richardson, S., Wyszynski, M. and Megaritis, T. (2005). Modeling of HCCI engines: Comparison of single-zone, multi-zone and test data. SAE Paper No. 2005-01-2123.