Numerical modelling of high-speed ball end milling with cutter inclination angle

Proceedings of the Institution of Mechanical Engineers, Part B: Journal of Engineering Manufacture

Volumn 226, Issue 4, 2012, Pages 606-616

  Chen, X X ^a   Zhao, J ^a   Li, Y E ^a,b   Han, S G ^a   Cao, Q Y ^a   Li, A H ^a  

^a SHANDONG UNIVERSITY   (China)

^b SHANDONG JIANZHU UNIVERSITY   (China)

Author keywords

ball end milling; high speed; inclination angle; numerical modelling

Indexed keywords

BALL END MILL; BALL END MILLING; BALL-END MILLING PROCESS; CHIP FORMATIONS; CUTTING FORCES; CUTTING PARAMETERS; EFFECTIVE STRESS; FINITE ELEMENT; FIVE-AXIS; FIVE-AXIS MACHINES; HIGH-SPEED; INCLINATION ANGLES; ISOTROPIC HARDENINGS; JOHNSON-COOK MODEL; MACHINING PROCESS; MAXIMUM CUTTING FORCE; NUMERICAL MODELLING; REMESHING; SHEAR ZONE; SIMULATION MODEL; WORKPIECE MATERIALS;

COMPUTER SIMULATION; CUTTING; FINITE ELEMENT METHOD; MACHINING CENTERS; MILLING (MACHINING); NUMERICAL MODELS; SPHERES;

BALL MILLING;

EID: 84860245667     PISSN: 09544054     EISSN: 20412975     Source Type: Journal    
DOI: 10.1177/0954405411426235     Document Type: Article

References (31)

1. Dewes R. C., Aspinwall D. K.. A review of ultra high speed milling of hardened steels. J. Mater. Processing Technol.. 1997 ; 69: 1-17
2. Baker M.. Finite element simulation of high-speed cutting forces. J. Mater. Processing Technol.. 2006 ; 176 (1-3). 117-126
3. Ozel T.. The influence of friction models on finite element simulations of machining. Int. J. Mach. Tools Mf.. 2006 ; 46 (5). 518-530
4. Arrazola P. J., Azel Tr.. Investigations on the effects of friction modeling in finite element simulation of machining. Int. J. Mech. Sci.. 2010 ; 52 (1). 31-42
5. Bonnet C., Valiorgue F., Rech J., Hamdi H.. Improvement of the numerical modeling in orthogonal dry cutting of an AISI 316L stainless steel by the introduction of a new friction model. CIRP J. Mfg Sci. Technol.. 2008 ; 1 (2). 114-118
6. Bahi S., Nouari M., Moufki A., El. Mansori M., Molinari A.. A new friction law for sticking and sliding contacts in machining. Tribol. Int.. 2011 ; 44 (7-8). 764-771
7. Nasr M., Ng E. G., Elbestawi M.. Effects of workpiece thermal properties on machining-induced residual stresses-thermal softening and conductivity. Proc. IMechE, Part B: J. Engineering Manufacture. 2007 ; 221 (9). 1387-1400
8. Nasr M., Ng E. G., Elbestawi M.. Modelling the effects of tool-edge radius on residual stresses when orthogonal cutting AISI 316L. Int. J. Mach. Tools Mf.. 2007 ; 47 (2). 401-411
9. Nasr M.. A modified time-efficient FE approach for predicting machining-induced residual stresses. Finite Elem. Anal. Des.. 2008 ; 44 (4). 149-161
10. Schulze V., Autenrieth H., Deuchert M., Weule H.. Investigation of surface near residual stress states after micro-cutting by finite element simulation. CIRP Annals Mf. Technol.. 2010 ; 59 (1). 117-120
11. Simoneau A., Ng E., Elbestawi M.. Modeling the effects of microstructure in metal cutting. Int. J. Mach. Tools Mf.. 2007 ; 47 (2). 368-375
12. Umbrello D., Msaoubi R., Outeiro J.. The influence of Johnson-Cook material constants on finite element simulation of machining of AISI 316L steel. Int. J. Mach. Tools Mf.. 2007 ; 47 (3-4). 462-470
13. Umbrello D.. Finite element simulation of conventional and high speed machining of Ti6Al4V alloy. J. Mater. Processing Technol.. 2008 ; 196 (1-3). 79-87
14. Lin Z., Huang J.. The influence of different cutting speeds on the cutting force and strain-stress behaviors of single crystal copper during nano-scale orthogonal cutting. J. Mater. Processing Technol.. 2008 ; 201 (1-3). 477-482
15. Hortig C., Svendsen B.. Simulation of chip formation during high-speed cutting. J. Mater. Processing Technol.. 2007 ; 186 (1-3). 66-76
16. Yen Y.. A finite element analysis of orthogonal machining using different tool edge geometries. J. Mater. Processing Technol.. 2004 ; 146 (1). 72-81
17. Yen Y.. Estimation of tool wear in orthogonal cutting using the finite element analysis. J. Mater. Processing Technol.. 2004 ; 146 (1). 82-91
18. Kone F., Czarnota C., Haddag B., Nouari M.. Finite element modelling of the thermo-mechanical behavior of coatings under extreme contact loading in dry machining. Surf Coating Tech.. 2011 ; 205 (12). 3559-3566
19. Ceretti E., Lazzaroni C., Menegardo L., Altan T.. Turning simulations using a three-dimensional FEM code. J. Mater. Processing Technol.. 2000 ; 98 (1). 99-103
20. Guo Y. B., Liu C. R.. 3D FEA modeling of hard turning. J. Mf. Sci. Eng.. 2002 ; 124 (2). 189-199
21. Soo S. L.. 3D FE modelling of the cutting of Inconel 718. J. Mater. Processing Technol.. 2004 ; 150 (1-2). 116-123
22. Soo S. L., Dewes R. C., Aspinwall D. K.. 3D FE modelling of high-speed ball nose end milling. Int. J. Advd Mfg Technol.. 2010 ; 50 (9-12). 871-882
23. Jiang B., Zheng M. L., Yang S. C., Fu M.. Research on high speed ball-end milling forces. Key Eng. Mater.. 2006 ; 315-316 (25). 25-29
24. Yücesan G.. and Altintas, Y. Prediction of ball end milling forces. ASME J. Eng. Ind.. 1996 ; 118 (1). 95-103
25. Lee P., Altintas Y.. Prediction of ball end milling forces from orthogonal cutting data. Int. J. Mach. Tools Mf.. 1996 ; 36 (9). 1059-1072
26. Landers R. G., Galecki G., Young K., Hanks R.. Peripheral milling of thin titanium plates: modelling, analysis, and process planning. Proc. IMechE, Part B: J. Engineering Manufacture. 2011 ; 225 (6). 783-798
27. Milfelner M., Cus F.. Simulation of cutting forces in ball-end milling. Robot Comput. Integrated Mf.. 2003 ; 19 (1-2). 99-106
28. Salami R., Sadeghi M. H., Motakef B.. Feed rate optimization for 3-axis ball-end milling of sculptured surfaces. Int. J. Mach. Tools Mf.. 2007 ; 47 (5). 760-767
29. Liu N., Loftus M.. Prediction of surface quality from ball-nose milling in high-speed machining applications. Proc. IMechE, Part B: J. Engineering Manufacture. 2006 ; 220 (4). 571-578
30. Sims N. D., Turner M. S.. The influence of feed rate on process damping in milling: modelling and experiments. Proc IMechE, Part B: J. Engineering Manufacture. 2011 ; 225 (6). 799-810
31. Chen S. L., Chang C. C., Chang C. H.. Application of a neural network for improving the quality of five-axis machining. Proc. IMechE, Part B: J. Engineering Manufacture. 2000 ; 214 (1). 47-59