3D FEA modeling of hard turning

Journal of Manufacturing Science and Engineering

Volumn 124, Issue 2, 2002, Pages 189-199

  Guo, Y B ^a   Liu, C R ^a  

^a SCHOOL OF INDUSTRIAL ENGINEERING   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COMPUTATIONAL GEOMETRY; COMPUTER SIMULATION; CUTTING TOOLS; FAILURE (MECHANICAL); FINITE ELEMENT METHOD; FRICTION; INTERFACES (MATERIALS); PLASTICITY; RESIDUAL STRESSES; SHEAR FLOW; STEEL; STRESS ANALYSIS; THERMOELASTICITY;

HARD TURNING;

TURNING;

EID: 0036588441     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1430678     Document Type: Article

References (34)

1. Matsumoto, Y., Barash, M.M., and Liu, C.R., 1986, "Effects of Hardness on the Surface Integrity of AISI 4340 Steel", ASME J. Eng. Ind., 108, pp. 169-175.
2. Koenig, W., Berktold, A., and Koch, K.F., 1993, "Turning Versus Grinding-A Comparison of Surface Integrity Aspects and Attainable Accuracy", CIRP Ann., 42/1, pp. 39-43.
3. Toenshoff, H.K., Wobker, H.G., and Brandt, D., 1995, "Hard Turning-Influences on the Workpiece Properties", Trans. of NAMRI/SME, Vol. XXIII, pp. 215-220.
4. Liu, C.R., and Mittal, S., 1996, "Single-Step Superfinish Hard Machining: Feasibility-and Feasible Cutting Conditions", Rob. Comput-Integr. Manufact., 12, No. 1, pp. 15-27.
5. Ng, E.G., Aspinwall, D.K., Brazil, D., and Monaghan, J., 1999, "Modeling of Temperature and Forces When Orthogonally Machining Hardened Steel", Int. J. Mach. Tools Manuf., 39, pp. 885-903.
6. Van Luttervelt, C.A., Childs, T.H.C., Jawahir, I.S., Klocke, F., and Venuvinod, P.K., 1998, "Present Situation and Future Trends in Modeling of Machining Operations-Progress Report of the CIRP Working Group 'Modeling of Machining Operations",' CIRP Ann., 47/2, pp. 587-626.
7. Elbestawi, M.A., Srivastava, A.K., and El-Wardany, T.I., 1996, "A Model for Chip Formation During Machining of Hardened Steel", CIRP Ann., 45/1, pp. 71-76.
8. Nakayama, K., Arai, M., and Kanda, T., 1988, "Machining Characteristics of Hard Materials", CIRP Ann., 37/1, pp. 89-92.
9. Chou, Y.K., and Evans, C., 1997, "Finish Hard Turning of Powder Metallurgy M50 Steel", Trans. of NAMRI/SME, Vol. XXV, pp. 81-86.
10. Wu, D.M., and Matsumoto, Y., 1990, "The Effect of Hardness on Residual Stresses in Orthogonal Machining of AISI 4340 Steel", ASME J. Eng. Ind., 112, pp. 245-252.
11. da Marcio, B.S., and Wallbank, J., 1999, "Cutting Temperature: Prediction and Measurement Methods - a Review", J. Mater. Process. Technol., 88, pp. 195-202.
12. Wang, J.Y., and Liu, C.R., 1998, "A New Concept for Decoupling the Cutting Forces due to Tool Flank Wear and Chip Formation in Hard Turning", Mach. Sci. Technol., 2(1), pp. 77-90.
13. Abrao, A.M., and Aspinwall, D.K., 1997, "Temperature Evaluation of Cutting Tools During Machining of Hardened Bearing Steel Using Polycrystalline Cubic Boron Nitride and Ceramic Cutting Tools", J. Mater. Sci. Technol., 13, May, pp. 445-450.
14. Ueda, T., Huda, M.A., Yamada, K., and Nakayama, K., 1999, "Temperature Measurement of CBN Tool in Turning of High Hardness Steel", CIRP Ann., 48/1, pp. 63-66.
15. Strenkowski, J.S., and Carroll, J.T., 1985, "A Finite Element Model of Orthogonal Metal Cutting", ASME J. Eng. Ind., 107, pp. 349-354.
16. Lin, Z.C., Lin, Y.Y., and Liu, C.R., 1991, "Effects of Thermal Load and Mechanical Load on the Residual Stress in a Machined Surface", Int. J. Mech. Sci., 33, No. 4, pp. 263-278.
17. Shih, A.J., 1995, "Finite Element Simulation of Orthogonal Metal Cutting", ASME J. Eng. Ind., 117, pp. 84-93.
18. Obikawa, T., Sasahara, H., Shirakashi, T., and Usui, E., 1997, "Application of Computational Machining Method to Discontinuous Chip Formation", ASME J. Manuf. Sci. Eng., 119, pp. 667-674.
19. Sasahara, H., Obikawa, T., and Shirakashi, T., 1997, "Finite Element Modeling of Residual Stress Control on Machined Surface", Transactions of NAMRI/ SME, Vol. XXV, pp. 231 218.
20. Guo, Y.B., and Liu, C.R., 2000, "Residual Stress Formation Mechanism and its Control by Sequential Cuts", Trans. of NAMRI/SME, Vol. XXVIII, pp. 179-184.
21. Guo, Y.B., and Dornfeld, D.A., 2000, "Finite Element Modeling of Drilling Burr Formation Process", ASME J. Manuf. Sci. Eng., 122, pp. 612-619.
22. Oxley, P.L.B., 1989, The Mechanics of Machining, Ellis Horwood Limited, Chichester, England, UK.
23. Stevenson, R., 1997, "Study on the Correlation of Workpiece Mechanical Properties from Compression and Cutting Tests", Mach. Sci. Technol., 1(1), pp. 67-79.
24. Shatla, M., and Altan, T., 2000, "Determination of Flow Stress for Machining and Practical Applications of FEM and Analytical Modeling", Proc. Of the 2000 NSF Design & Manufacturing Res. Conf., http://www.engr.washington.edu/̃uwepp/nsf/.
25. Guo, Y.B., and Liu, C.R., 1999, "Mechanical Properties of Hardened AISI 52100 Steel in Hard Machining Processes", ASME 1. Manuf. Sci. Eng., in press.
26. Usui, E., and Shirakashi, T., 1982, "Mechanics of Machining From Descriptive to Predictive Theory", ASME PED-7, pp. 13-45.
27. Guo, Y.B., 2000, "Finite Element Analysis of Superfinish Hard Turning", Ph.D. Dissertation, May, Purdue University.
28. Marusich, T.D., and Ortiz, M., 1994, "Simulation of High-Speed Machining", Recent Developments in Finite Element Analysis, CIMNE, Barcelona.
29. Liu, C.R., and Guo, Y.B., 2000, "Finite Element Analysis of the Effect of Sequential Cuts and Tool-Chip Friction on Residual Stresses in a Machined Layer", Int. J. Mech. Sci., 42/6, pp. 1069-1086.
30. Hibbit, Karlsson, and Sorenson, Inc., 1999, ABAQUS/Explicit User's Manual, ver.5.8, Providence, RI.
31. Reddy, J.N., 1993, An Introduction to the Finite Element Method, McGraw-Hill, Inc.
32. Burwell, J.T., and Strang, C.D., 1952, J. Appl. Phys., 23, p. 18.
33. Shaw, M.C., 1984, Metal Cutting Principles, Oxford University Press Inc., New York.
34. Lin, Z.C., and Lee, B.Y., 1995, "An Investigation of the Residual Stress of a Machined Workpiece Considering Tool Flank Wear", J. Mater. Process. Technol., 51, pp. 1-24.