On-die CMOS voltage droop detection and dynamic compensation

Proceedings of the ACM Great Lakes Symposium on VLSI, GLSVLSI

Volumn , Issue , 2008, Pages 35-40

  Holtz, Matthew A ^a   Narasimhan, Seetharam ^b   Bhunia, Swarup ^b  

^a Keithley Instruments Inc   (United States)

^b CASE WESTERN RESERVE UNIVERSITY   (United States)

Author keywords

Di dt voltage droop; On die voltage droop compensation; Power supply droop; Predictive current injection

Indexed keywords

DI/DT VOLTAGE DROOP; DYNAMIC COMPENSATIONS; HIGH CURRENTS; LOW VOLTAGES; ON-DIE VOLTAGE DROOP COMPENSATION; POWER SUPPLY DROOP; PREDICTIVE CURRENT INJECTION; SIMULATION AND ANALYSES;

DIES; ELECTRIC POWER DISTRIBUTION; ELECTRIC POWER TRANSMISSION NETWORKS; ELECTRIC POWER UTILIZATION; LAKES; NETWORKS (CIRCUITS); VLSI CIRCUITS;

SPICE;

EID: 56749130062     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1145/1366110.1366122     Document Type: Conference Paper

References (12)

1. E. Alon, V. Stojanović, and M. Horowitz. Circuits and techniques for high-resolution measurement of on-chip power supply noise. In VLSI Circuits Digest of Technical Papers, pages 102-105, June 2004.
2. H. Aoki, M. Ikeda, and K. Asada. On-chip voltage noise monitor for measuring voltage bounce in power supply lines using a digital tester. In International Conference on Microelectronic Test Structures, pages 112-117, 2000.
3. G. Bai, S. Bobba, and I. N. Hajj. Static timing analysis including power supply noise effect on propagation delay in VLSI circuits. In Proceedings of the Design Automation Conference, pages 295-300, 2001.
4. C. Chansungsan. Auto-referenced on-die power supply noise measurement circuit. In IEEE Custom Integrated Circuits Conference, pages 39-42, September 2005.
5. Intel Corporation. Intel Processor QX6000 Sequence and Q6000 Sequence Datasheet. Microprocessor Databook.
6. S. Kim, S. V. Kosonocky, and D. R. Knebel. Understanding and minimizing ground bounce during mode transition of power gating structures. In International Symposium on Low Power Electronics and Design, pages 22-25, August 2003.
7. A. Muhtaroglu, G. Taylor, and T. Rahal-Arabi. On-die droop detector for analog sensing of power supply noise. IEEE J. Solid-State Circuits, 39(4):651-660, April 2004.
8. T. Nakura, M. Ikeda, and K. Asada. Power supply noise reduction using stubs. IEICE technical report, 103(480):217-222, 2003.
9. T. Rahal-Arabi, G. Taylor, M. Ma, and C. Webb. Design and validation of the Pentium III and Pentium 4 processors power delivery. In Symposium On VLSI Circuits Digest of Technical Papers, pages 220-223, June 2002.
10. R. Senthinathan and J. Prince. Application specific CMOS output driver circuit design techniques to reduce simultaneous switching noise. IEEE J. Solid-State Circuits, 28(12):1383-1388, December 1993.
11. L. D. Smith, R. E. Anderson, D. W. Forehand, T. J. Pelc, and T. Roy. Power distribution system design methodology and capacitor selection for modern CMOS technology. IEEE Trans. Adv. Packag., 22(3):284-291, August 1999.
12. K. L. Wong, T. Rahal-Arabi, M. Ma, and G. Taylor. Enhancing microprocessor immunity to power supply noise with clock-data compression. IEEE J. Solid-State Circuits, 41(4):749-758, April 2006.