Surge Arresters

Power System Transients: Parameter Determination

Volumn , Issue , 2017, Pages 351-546

  Martinez Velasco, Juan A ^a   Castro Aranda, Ferley ^b  

^a UNIVERSITAT POLITÈCNICA DE CATALUNYA   (Spain)

^b UNIVERSIDAD DEL VALLE   (Colombia)

Author keywords

[No Author keywords available]

Indexed keywords

EID: 85138030619     PISSN: None     EISSN: None     Source Type: Book    
DOI: 10.1201/9781420065305-6     Document Type: Chapter

References (150)

1. P. Chowdhuri, Electromagnetic Transients in Power Systems, RSP-Wiley, Taunton, U.K., 1996.
2. IEEE Std C62.1-1989, IEEE standard for gapped silicon-carbide surge arresters for AC power circuits.
3. IEEE Std C62.2-1987, IEEE guide for the application of gapped silicon-carbide surge arresters for alternating current systems.
4. IEEE Std C62.11-2005, IEEE standard for metal-oxide surge arresters for ac power circuits (>1 kV).
5. IEEE Std C62.22-1997, IEEE guide for the application of metal-oxide surge arresters for alternating- current systems.
6. IEC Std 60099-1, Surge arresters-Part 1: Non-linear resistor type gapped surge arresters for a.c. systems, edition 3.1, 1999.
7. IEC Std 60099-3, Surge arresters-Part 3: Artificial pollution testing of surge arresters, 1st edn., 1990.
8. IEC Std 60099-4, Surge arresters-Part 4: Metal-oxide surge arresters without gaps for a.c. systems, edition 2.1, 2006.
9. IEC Std 60099-5, Surge arresters-Part 5: Selection and application recommendations, edition 1.1, 2000.
10. IEC Std 60099-6, Surge arresters-Part 6: Surge arresters containing both series and parallel gapped structures-Rated 52 kV and less, 1st edn., 2002.
11. D.P. Carroll, R.W. Flugum, J.W. Kalb, and H.A. Peterson, A dynamic surge arrester model for use in power system transient studies, IEEE Transactions on Power Apparatus and Systems, 92(3), 1057-1066, May/June 1972.
12. A.P. Sakis Meliopoulos, Lightning and overvoltage protection, Section 27 of Standard Handbook for Electrical Engineers, D.G. Fink and H. Wayne Beaty (Eds.), 14th edn., McGraw-Hill, 2000.
13. N. Fujiwara et al., Development of a pin-post insulator with built-in metal oxide varistors for distribution lines, IEEE Transactions on Power Delivery, 11(2), 824-833, April 1996.
14. Y. Harumoto et al., Evaluation for application of built-in type zinc oxide gapless surge arresters for power system equipments, IEEE Transactions on Power Delivery, 2(3), 750-757, July 1987.
15. A.R. Hileman, Insulation Coordination for Power Systems, Marcel Dekker, New York, 1999.
16. T.E. McDermott, Surge Arresters, Chapter 13 of Power Systems, L.L. Grigsby (Ed.), CRC Press, New York, 2007.
17. S. Gu et al., Development of surge arresters with series gap against lightning breakage of covered conductors on distribution lines, IEEE Transactions on Power Delivery, 22(4), 2191-2198, October 2007.
18. G.L. Goedde, Lj.A. Kojovic, M.B. Marz, and J.J. Woodworth, Series graded gapped arrester provides reliable overvoltage protection in distribution networks, IEEE PES Winter Meeting, 28 January-1 February, 2001, Columbus, OH.
19. J. Osterhout, Comparison of IEC and IEEE standards for metal oxide surge arresters, IEEE Transactions on Power Delivery, 7(4), 2002-2006, October 1992.
20. S. Kojima, S. Nishiwaki, and T. Sato, Switching surge duty of metal oxide surge arresters in multiphases system and its equivalent conditions in a test, IEEE Transactions on Power Delivery, 2(4), 117-1123, October 1987.
21. E.C. Sakshaug, J.J. Burke, and J.S. Kresge, Metal oxide arresters on distribution systems. Fundamental considerations, IEEE Transactions on Power Delivery, 4(4), 2076-2089, October 1989.
22. K.G. Ringler, P. Kirkby, C.C. Erven, M.V. Lat, and T.A. Malkiewicz, The energy absorption capability and time-to-failure of varistors used in station-class metal-oxide surge arresters, IEEE Transactions on Power Delivery, 12(1), 203-212, January 1997.
23. P. Kirkby, C.C. Erven, and O. Nigol, Long-term stability and energy discharge capacity of metal oxide valve elements, IEEE Transactions on Power Delivery, 3(4), 1656-1665, October 1988.
24. M.L.B. Martinez and L.C. Zanetta, On modeling and testing metal oxide resistors to evaluate the arrester withstand energy, Dielectric Materials, Measurements and Applications Conference, Edinburg, U.K., Paper 473, pp. 247-252, IEE 2000.
25. M.L.B. Martinez and L.C. Zanetta, A proposal to evaluate the energy withstand capacity of metal oxide resistors, High Voltage Engineering Symposium, London, U.K., Paper 467, August 1999.
26. M. Bartkowiak, M.G. Comber, and G.D. Mahan, Failure modes and energy absorption capability of ZnO varistors, IEEE Transactions on Power Delivery, 14(1), 152-162, January 1999.
27. CIGRE WG 33.02, Guidelines for Representation of Network Elements when Calculating Transients, CIGRE Brochure 39, 1990.
28. H.W. Dommel, Electromagnetic Transients Program Reference Manual (EMTP Theory Book), Bonneville Power Administration, Portland, August 1986.
29. J.A. Martinez and D. Durbak, Parameter determination for modeling systems transients. Part V: Surge arresters, IEEE Transactions on Power Delivery, 20(3), 2073-2078, July 2005.
30. E.C. Sakshaug, Influence of rate-of-rise on distribution arrester protective characteristics, IEEE Transactions on Power Apparatus and Systems, 98(2), 519-526, March/April 1979.
31. S. Tominaga et al., Protective performance of metal oxide surge arrester based on the dynamic V-I characteristics, IEEE Transactions on Power Apparatus and Systems, 98(6), 1860-1871, November/December 1979.
32. D.W. Durbak, Zinc-oxide arrester model for fast surges, EMTP Newsletter, 5(1), 1-9, January 1985.
33. C. Dang, T.M. Parnell, and P.J. Price, The response of metal oxide surge arresters to steep fronted current impulses, IEEE Transactions on Power Delivery, 1(1), 157-163, January 1986.
34. D.W. Durbak, The choice of EMTP surge arrester models, EMTP Newsletter, 7(3), 14-18, September 1987.
35. W. Schmidt et al., Behavior of MO-surge-arrester blocks to fast transients, IEEE Transactions on Power Delivery, 4(1), 292-300, January 1989.
36. A.R. Hileman, J. Roguin, and K.H. Weck, Metal oxide surge arresters in AC systems. Part V:Protection performance of metal oxide surge arresters, Electra, 133, 132-144, December 1990.
37. IEEE Working Group on Surge Arrester Modeling, Modeling of metal oxide surge arresters, IEEE Transactions on Power Delivery, 7(1), 302-309, January 1992.
38. I. Kim et al., Study of ZnO arrester model for steep front wave, IEEE Transactions on Power Delivery, 11(2), 834-841, April 1996.
39. P. Pinceti and M. Giannettoni, A simplified model for zinc oxide surge arresters, IEEE Transactions on Power Delivery, 14(2), 393-398, April 1999.
40. M. Caserza Magro, M. Giannettoni, and P. Pinceti, Validation of ZnO surge arresters model for overvoltage studies, IEEE Transactions on Power Delivery, 19(4), 1692-1695, October 2004.
41. CIGRE WG 33.06, Metal Oxide Arresters in AC Systems, Technical Brochure 60, 1991.
42. F. Heidler, J.M. Cvetic, and B.V. Stanic, Calculation of lightning current parameters, IEEE Transactions on Power Delivery, 14(2), 399-404, April 1999.
43. IEEE TF on Parameters of Lightning Strokes, Parameters of lightning strokes: A review, IEEE Transactions on Power Delivery, 20(1), 346-358, January 2005.
44. H.J. Li, S. Birlasekaran, and S.S. Choi, A parameter identification technique for metal-oxide surge arrester models, IEEE Transactions on Power Delivery, 17(3), 736-741, July 2002.
45. M.V. Lat, Thermal properties of metal oxide surge arresters, IEEE Transactions on Power Apparatus and Systems, 102(7), 2194-2202, July 1983.
46. M.V. Lat, Analytical method for performance prediction of metal oxide surge arresters, IEEE Transactions on Power Apparatus and Systems, 104(10), 2665-2674, October 1985.
47. G. St-Jean and A. Petit, Metal-oxide surge arrester operating limits defined by a temperaturemargin concept, IEEE Transactions on Power Delivery, 5(2), 627-633, April 1990.
48. A. Petit, X.D. Do, and G. St-Jean, An experimental method to determine the electro-thermalt model parameters of metal oxide arresters, IEEE Transactions on Power Delivery, 6(2), 715-721, April 1991.
49. A. Haddad, ZnO Surge Arresters, Chapter 5 of Advances in High Voltage Engineering, A. Haddad and D. Warne (Eds.), The Institution of Electrical Engineers, 2004.
50. S. Nishiwaki, H. Kimura, T. Satoh, H. Mizoguchi, and S. Yanabu, Study of thermal runaway/equivalent prorated model of a ZnO surge arrester, IEEE Transactions on Power Apparatus and Systems, 103, 413-421, February 1984.
51. M. Kan, S. Nishiwaki, T. Sato, S. Kojima, and S. Yanabu, Surge discharge capability and thermal stability of a metal oxide surge arrester, IEEE Transactions on Power Apparatus and Systems, 102(2), 282-289, February 1983.
52. F.R. Stockum, Simulation of the nonlinear thermal behavior of metal oxide surge arresters using a hybrid finite difference and empirical model, IEEE Transactions on Power Delivery, 9(1), 306-313, January 1994.
53. E. Guedes da Costa, S.R. Naidu, and A. Guedes da Lima, Electrothermal model for complete metal-oxide surge arresters, IEE Proceedings-Generation, Transmission and Distribution, 148(1), 29-33, January 2001.
54. O. Nigol, Methods for analyzing the performance of gapless metal oxide surge arresters, IEEE Transactions on Power Delivery, 7(3), 1256-1264, July 1992.
55. S. Boggs, J. Kuang, H. Andoh, and S. Nishiwaki, Electro-thermal-mechanical computations in ZnO arrester elements, IEEE Transactions on Power Delivery, 15(1), 128-134, July 2000.
56. Z. Zheng, S. Nishiwaki, S. Boggs, and T. Fukano, Effects of heat sinks in metal-oxide surge arresters on ZnO element power dissipation and temperature distribution, IEEE Transactions on Power Delivery, 20(2), 1402-1408, April 2005.
57. Z. Zheng et al. Investigation of heat-of-fusion heat sinks for polymer-type metal-oxide surge arresters, 2006 IEEE International Symposium on Electrical Insulation, Tuscaloosa, AL, 2005.
58. IEEE Std 1313.2-1999, IEEE Guide for the Application of Insulation Coordination.
59. IEC 60071-2, Insulation co-ordination, Part 2: Application Guide, 1996.
60. A. Greenwood, Electrical Transients in Power Systems, John Wiley, New York, 1971.
61. IEEE Std 1313-1996, IEEE Standard for Insulation Coordination-Definitions, Principles and Rules.
62. IEC 60071-1, Insulation Co-ordination, Part 2: Definitions, principles and rules, 2006.
63. R.A. Jones and H.S. Fortson Jr., Consideration of phase-to-phase surges in application of capacitor banks, IEEE Transactions on Power Delivery, 1(3), 240-244, July 1986.
64. R.P. O’Leary and R.H. Harner, Evaluation of methods for controlling the overvoltages produced by the energization of a shunt capacitor bank, CIGRE Session, Paper No. 13-05, 1988, Paris.
65. A.J.F. Keri, Y.I. Musa, and J.A. Halladay, Insulation coordination for delta connected transformers, IEEE Transactions on Power Delivery, 9(2), 772-780, April 1994.
66. IEEE Task Force on Slow Transients, Modeling and analysis guidelines for slow transients-Part III: The study of ferroresonance, IEEE Transactions on Power Delivery, 15(1), 255-265, January 2000.
67. R.H. Hopkinson, Ferroresonance during single-phase switching of 3-phase distribution transformer banks, IEEE Transactions on Power Apparatus and Systems, 84(4), 289-293, April 1965.
68. F.S. Young, R.L. Schmid, and P.I. Fergestad, A laboratory investigation of ferroresonance in cable-connected transformers, IEEE Transactions on Power Apparatus and Systems, 87(5), 1240-1249, May 1968.
69. R.A. Walling et al., Performance of metal-oxide arresters exposed to ferroresonance in padmount transformers, IEEE Transactions on Power Delivery, 9(2), 788-795, April 1994.
70. R.E. Koch et al., Design of zinc oxide transmission line arresters for application on 138 kV towers, IEEE Transactions on Power Apparatus and Systems, 104(10), 2675-2680, October 1985.
71. C.H. Shih et al., Application of special arresters on 138 kV lines of Appalachian Power Company, IEEE Transactions on Power Apparatus and Systems, 104(10), 2857-2863, October 1985.
72. S. Furukawa, O. Usuda, T. Isozaki, and T. Irie, Development and application of lightning arresters for transmission lines, IEEE Transactions on Power Delivery, 4(4), 2121-2129, October 1989.
73. K. Ishida et al., Development of a 500 kV transmission line arrester and its characteristics, IEEE Transactions on Power Delivery, 7(3), 1265-1274, July 1992.
74. T. Yamada et al., Development of suspension-type arresters for transmission lines, IEEE Transactions on Power Delivery, 8(3), 1052-1060, July 1993.
75. J.L. He, S.M. Chen, R. Zeng, J. Hu, and C.G. Deng, Development of polymeric surge ZnO arresters for 500-kV compact transmission line, IEEE Transactions on Power Delivery, 21(1), 113-120, January 2006.
76. R.A. Sargent, G.L. Dunlop, and M. Darveniza, Effects of multiple impulse currents on the microstructure and electrical. Properties of metal-oxide varistors, IEEE Transactions on Electrical Insulation, 27(3), 586-592, June 1992.
77. M. Darveniza, D. Roby, and L.R. Tumma, Laboratory and analytical studies of the effects of multipulse lightning current on metal oxide arresters, IEEE Transactions on Power Delivery, 9(2), 764-771, April 1994.
78. M. Darveniza, L.R. Tumma, B. Richter, and D. Roby, Multipulse lightning currents and metal oxide arresters, IEEE Transactions on Power Delivery, 12(3), 1168-1175, July 1997.
79. Y. Matsumoto et al., Measurement of lightning surges on test transmission line equipped with arresters struck by natural and triggered lightning, IEEE Transactions on Power Delivery, 11(2), 996-1002, April 1996.
80. T.A. Short et al., Application of surge arresters to a 115 kV circuit, IEEE PES Transmission and Distribution Conference and Exposition, Los Angeles, September 1996.
81. S. Sadovic, R. Joulie, S. Tartier, and E. Brocard, Use of line surge arresters considering the total lightning performance of 63 kV and 90 kV shielded and unshielded transmission lines, IEEE Transactions on Power Delivery, 12(3), 1232-1240, July 1997.
82. T. Kawamura et al., Experience and effectiveness of application of arresters to overhead transmission lines, CIGRE Session, Paper 33-301, 1998, Paris.
83. E.J. Tarasiewicz, F. Rimmer, and A.S. Morched, Transmission line arresters energy, cost, and risk of failure analysis for partially shielded transmission lines, IEEE Transactions on Power Delivery, 15(3), 919-924, July 2000.
84. T. Wakai, N. Itamoto, T. Sakai, and M. Ishii, Evaluation of transmission line arresters against winter lightning, IEEE Transactions on Power Delivery, 15(2), 684-690, April 2000.
85. L.C. Zanetta and C.E. de Morais Pereira, Application studies of line arresters in partially shielded 138-kV transmission lines, IEEE Transactions on Power Delivery, 18(1), 95-100, January 2003.
86. L.C. Zanetta, Evaluation of line surge arrester failure rate for multipulse lightning stresses, IEEE Transactions on Power Delivery, 18(3), 706-801, July 2003.
87. L. Stenström, Required energy capability based on total charge for a transmission line arrester for protection of a compact 420 kV line for Swedish conditions, CIGRE International Colloquium on Insulation Coordination, September 2-3, 1997, Toronto.
88. L. Stenström and J. Lundquist, Energy stress on transmission line arresters considering the total lightning charge distribution, IEEE Transactions on Power Delivery, 14(1), 148-151, January 1999.
89. CIGRE WG 33.11, Application of metal oxide surge arresters to overhead lines, Electra, no. 186, 82-112, October 1999.
90. M.A. Ismaili, P. Bernard, R. Lambert, and A. Xémard, Estimating the probability of failure of equipment as a result of direct lightning strikes on transmission lines, IEEE Transactions on Power Delivery, 14(4), 1394-1400, October 1999.
91. M.S. Savic, Estimation of the surge arrester outage rate caused by lightning overvoltages, IEEE Transactions on Power Delivery, 20(1), 116-122, January 2005.
92. T. Hayashi, Y. Mzuno, and K. Naito, Study on transmission-line arresters for tower with high footing resistance, IEEE Transactions on Power Delivery, 23(4), 2456-2460, October 2008.
93. A. Xemard, S. Sadovic, I. Uglesic, L. Prikler, and J.A. Martinez, Developments on the Line Surge Arresters Application Guide prepared by the CIGRE WG C4 301, CIGRE Symposium on Transients in Large Electric Power Systems, April 18-21, 2007, Zagreb.
94. G.W. Brown and E.R. Whitehead, Field and analytical studies of transmission line shielding:Part II, IEEE Transactions on Power Apparatus and Systems, 88(3), 617-626, May 1969.
95. IEEE TF on Fast Front Transients, Modeling guidelines for fast transients, IEEE Transactions on Power Delivery, 11(1), 493-506, January 1996.
96. Modeling and Analysis of System Transients Using Digital Programs, A.M. Gole, J.A. Martinez-Velasco and A.J.F. Keri (Eds.), IEEE PES Special Publication, TP-133-0, 1999.
97. IEC TR 60071-4, Insulation Co-ordination Part 4: Computational guide to insulation coordination and modelling of electrical networks, 2004.
98. J.A. Martinez-Velasco and F. Castro-Aranda, Modelling guidelines for overhead transmission lines in lightning studies, CIGRE Symposium on Transients in Large Electric Power Systems, April 18-21, 2007, Zagreb.
99. CIGRE WG 33.01, Guide to Procedures for Estimating the Lightning Performance of Transmission Lines, Technical Brochure 63, 1991.
100. CIGRE WG 33.01, Guide for the Evaluation of the Dielectric Strength of External Insulation, Technical Brochure 72, 1992.
101. A. Pigini et al., Performance of large air gaps under lightning over-voltages: Experimental study and analysis of accuracy of pre-determination methods, IEEE Transactions on Power Delivery, 4(2), 1379-1392, April 1989.
102. A.M. Mousa, The soil ionization gradient associated with discharge of high currents into concentrated electrodes, IEEE Transactions on Power Delivery, 9(3), 1669-1677, July 1994.
103. J.A. Martinez and F. Castro-Aranda, Lightning performance analysis of overhead transmission lines using the EMTP, IEEE Transactions on Power Delivery, 20(3), 2200-2210, July 2005.
104. W.A. Lyons, M. Uliasz, and T.E. Nelson, Large peak current cloud-to-ground lightning flashes during the summer months in the contiguous United States, Monthly Weather Review, 126, 2217-2233, 1998.
105. J.A. Martinez and F. Castro-Aranda, Modeling of overhead transmission lines for line arrester studies, IEEE PES General Meeting, June 2004, Denver.
106. A. Ametani and T. Kawamura, A method of a lightning surge analysis recommended in Japan using EMTP, IEEE Transactions on Power Delivery, 20(2), 867-875, April 2005.
107. V.A. Rakov and M.A. Uman, Lightning. Physics and Effects, Cambridge University Press, Cambridge, U.K., 2003.
108. J.A. Martinez and F. Castro-Aranda, Influence of the stroke angle on the flashover rate of an overhead transmission line, IEEE PES General Meeting 2006, June 2006, Montreal.
109. CIGRE 33/13.09, Monograph on GIS Very Fast Transients, July 1989.
110. M.M. Osborne, A. Xemard, L. Prikler, and J.A. Martinez, Points to consider regarding the insulation coordination of GIS substations with cable connections to overhead lines, Proceedings of the 7th International Conference on Power Systems Transients, 4-7, June 2007, Lyon.
111. CIGRE WG B1.05, Transient Voltages Affecting Long Cables, Technical Brochure 268, 2005.
112. T. Henriksen, B. Gustavsen, G. Balog, and U. Baur, Maximum lightning overvoltage along a cable protected by surge arresters, IEEE Transactions on Power Delivery, 20(2), 859-866, April 2005.
113. E.W. Greenfield, Transient behavior of short and long cables, IEEE Transactions on Power Apparatus and Systems, 103(11), 3193-3203, November 1984.
114. L. Marti, Simulation of transients in underground cables with frequency-dependent modal transformation matrices, IEEE Transactions on Power Delivery, 3(3), 1099-1110, July 1988.
115. H. van der Merwe and F.S. van der Merwe, Some features of traveling waves on cables, IEEE Transactions on Power Delivery, 8(3), 789-797, July 1993.
116. W.E. Reid et al., MOV arrester protection of shield interrupts on 138 kV extruded dielectric cables, IEEE Transactions on Power Apparatus and Systems, 103, 3334-3341, November 1984.
117. M.V. Lat and J. Kortschinski, Distribution arrester research, IEEE Transactions on Power Apparatus and Systems, 100(7), 3496-3505, July 1981.
118. S.S. Kershaw, G.L. Gaibrois, and K.B. Stump, Applying metal-oxide surge arresters on distribution systems, IEEE Transactions on Power Delivery, 4(1), 301-307, January 1989.
119. M.V. Lat, Determining temporary overvoltage levels for application of metal oxide surge arresters on multigrounded distribution systems, IEEE Transactions on Power Delivery, 5(2), 936-946, April 1990.
120. J.J. Burke, V. Varneckas, E. Chebli, and G Hoskey, Application of MOV and gapped arresters on non-effectively grounded distribution systems, IEEE Transactions on Power Delivery, 6(2), 794-800, April 1991.
121. R.T. Mancao, J.J. Burke, and A. Myers, The effect of distribution system grounding on MOV selection, IEEE Transactions on Power Delivery, 8(1), 139-145, January 1993.
122. T.A. Short, J.J. Burke, and R.T. Mancao, Application of MOVs in the distribution environment, IEEE Transactions on Power Delivery, 9(1), 293-305, January 1994.
123. F.J. Muench and J.P. Dupont, Coordination of MOV type lightning arresters and current limiting fuses, IEEE Transactions on Power Delivery, 5(2), 966-971, April 1990.
124. A. Hamel, G. St-Jean, and M. Paquette, Nuisance fuse operation on MV transformers during storms, IEEE Transactions on Power Delivery, 5(4), 1866-1874, October 1990.
125. W. Plummer et al., Reduction in distribution transformer failure rates and nuisance outages using improved lightning protection concepts, IEEE Transactions on Power Delivery, 10(2), 768-777, April 1995.
126. S. Yokoyama, Distribution surge arrester behavior due to lightning induced voltages, IEEE Transactions on Power Delivery, 1(1), 171-178, January 1986.
127. T.E. McDermott, T.A. Short, and J.G. Anderson, Lightning protection of distribution lines, IEEE Transactions on Power Delivery, 9(1), 138-152, January 1994.
128. T. Short and R.H. Ammon, Monitoring results of the effectiveness of surge arrester spacings on distribution line protection, IEEE Transactions on Power Delivery, 14(3), 1142-1150, July 1999.
129. IEEE Std 1410-1997, IEEE Guide for Improving the Lightning Performance of Electric Power Overhead Distribution Lines.
130. K. Nakada, T. Yokota, S. Yokoyama, A. Asakawa, M. Nakamura, H. Taniguchi, and A. Hashimoto, Energy absorption of surge arresters on power distribution lines due to direct lightning strokeseffects of an overhead ground wire and installation position of surge arresters, IEEE Transactions on Power Delivery, 12(4), 1779-1785, October 1997.
131. K. Nakada, S. Yokoyama, T. Yokota, A. Asakawa, and T. Kawabata, Analytical study on prevention methods for distribution arrester outages caused by winter lightning, IEEE Transactions on Power Delivery, 13(4), 1399-1404, October 1998.
132. K. Nakada et al., Distribution arrester failures caused by lightning current flowing from customer’s structure into distribution lines, IEEE Transactions on Power Delivery, 14(4), 1527-1532, October 1999.
133. M. Darveniza and D.R. Mercer, Lightning protection of pole mounted transformers, IEEE Transactions on Power Delivery, 4(2), 1087-1095, April 1989.
134. Lightning Protection Manual for Rural Electric Systems, NRECA, RER Project 92-12, 1993.
135. B. Wareing, Wood Pole Overhead Lines, The IEE, 2005.
136. C.F. Wagner and A.R. Hileman, Effect of predischarge current upon line performance, IEEE Transactions on Power Apparatus and Systems, 82(65), 117-131, April 1963.
137. G.W. Brown and S. Thunander, Frequency of distribution arrester discharge currents due to direct strokes, IEEE Transactions on Power Apparatus and Systems, 95(5), 1571-1578, September/October 1976.
138. J.A. Martinez and F. Gonzalez-Molina, Surge protection of underground distribution cables, IEEE Transactions on Power Delivery, 15(2), 756-763, April 2000.
139. J.J. Burke, E.C. Sakshaug, and S.L. Smith, The application of gapless arresters on distribution systems, IEEE Transactions on Power Apparatus and Systems, 100(3), 1234-1243, March 1981.
140. W.D. Niebuhr, Application of metal-oxide-varistor surge arresters on distribution systems, IEEE Transactions on Power Apparatus and Systems, 101(6), 1711-1715, June 1982.
141. M.V. Lat, A simplified method for surge protection of underground distribution systems with metal oxide arresters, IEEE Transactions on Power Delivery, 2(4), 1110-1116, October 1987.
142. G.L. Gaibrois, Lightning current surge magnitude through distribution arresters, IEEE Transactions on Power Apparatus and Systems, 100(3), 964-970, March 1981.
143. P.P. Baker, R.T. Mancao, D.J. Kvaltine, and D.E. Parrish, Characteristics of lightning surges measured at metal oxide distribution arresters, IEEE Transactions on Power Delivery, 8(1), 301-310, January 1993.
144. M.I. Fernandez, K.J. Rambo, V.A. Rakov, and M.A. Uman, Performance of MOV arresters during very close, direct lightning strikes to a power distribution system, IEEE Transactions on Power Delivery, 14(2), 411-418, April 1999.
145. J. Schoene et al., Direct lightning strikes to test power distribution lines-Part I: Experimental and overall results, IEEE Transactions on Power Delivery, 22(4), 2236-2244, October 2007.
146. J. Schoene et al., Direct lightning strikes to test power distribution lines-Part II: Measured and modeled current division among multiple arresters and ground, IEEE Transactions on Power Delivery, 22(4), 2245-2253, October 2007.
147. R.E. Owen and C.R. Clinkenbeard, Surge protection of UD cable systems. Part I: Cable attenuation and protection constraints, IEEE Transactions on Power Apparatus and Systems, 97(4), 1319-1327, July/August 1978.
148. R.C. Dugan and W.L. Sponsler, Surge protection of UD cable systems. Part II: Analytical models and simulations, IEEE Transactions on Power Apparatus and Systems, 97(5), 1901-1909, September/October 1978.
149. P.P. Baker, Voltage quadrupling on a UD cable, IEEE Transactions on Power Delivery, 5(1), 498-501, January 1990.
150. W.E. Feero and W.B. Gish, Overvoltages caused by DSG operation: Synchronous and induction generators, IEEE Transactions on Power Delivery, 1(1), 258-264, January 1986.