On the rate of injection modeling applied to direct injection compression ignition engines

International Journal of Engine Research

Volumn 17, Issue 10, 2016, Pages 1015-1030

  Payri, Raul ^a   Gimeno, Jaime ^a   Novella, Ricardo ^a   Bracho, Gabriela ^a  

^a UNIVERSITAT POLITÈCNICA DE VALÈNCIA   (Spain)

Author keywords

common rail; Diesel; engine; injection rate; zero dimensional model

Indexed keywords

DIESEL ENGINES; ENGINES; FLOW RATE; MACHINE DESIGN; MASS TRANSFER;

ADDITIONAL EXPERIMENTS; COMMON RAIL; DEVELOPMENT PROGRAMS; DIESEL; INJECTION COMPRESSION IGNITION ENGINE; INJECTION RATES; MATHEMATICAL EXPRESSIONS; ZERO-DIMENSIONAL MODELS;

DIRECT INJECTION;

EID: 84994545601     PISSN: 14680874     EISSN: 20413149     Source Type: Journal    
DOI: 10.1177/1468087416636281     Document Type: Article

References (30)

1. Fimml W, Chmela FG, Pirker G, Wimmer A., Influence of cavitation in the injection nozzle on combustion in diesel engines. Int J Engine Res 2010; 11: 375-390.
2. Benajes J, Novella R, de Lima D, Tribotté P., Analysis of combustion concepts in a newly designed two-stroke high-speed direct injection compression ignition engine. Int J Engine Res 2015; 16: 52-67.
3. Lapuerta M, Armas O, Hernández JJ., Diagnosis of DI diesel combustion from in-cylinder pressure signal by estimation of mean thermodynamic properties of the gas. Appl Therm Eng 1999; 19 (5): 513-529.
4. Benajes J, Olmeda P, Martín J, Carreño R., A new methodology for uncertainties characterization in combustion diagnosis and thermodynamic modelling. Appl Therm Eng 2014; 71: 389-399.
5. Payri F, Molina S, Martín J, Armas O., Influence of measurement errors and estimated parameters on combustion diagnosis. Appl Therm Eng 2006; 26 (2-3): 226-236.
6. Benajes J, García-Oliver J-M, Novella R, Kolodziej C., Increased particle emissions from early fuel injection timing Diesel low temperature combustion. Fuel 2012; 94: 184-190.
7. Benajes J, Novella R, Martín J, De Lima D,. Analysis of the load effect on the partially premixed combustion concept in a 2-stroke HSDI diesel engine fueled with conventional gasoline. SAE technical paper 2014-01-1291, 2014.
8. Musculus MPB, Miles PC, Pickett LM., Conceptual models for partially premixed low-temperature diesel combustion. Prog Energ Combust 2013; 39: 246-283.
9. Naber JD, Siebers DL., Effects of gas density and vaporization on penetration and dispersion of diesel sprays. SAE Trans 1996; 105 (3): 82-111.
10. Abraham J, Pickett LM., Computed and measured fuel vapor distribution in a diesel spray. Atomization Spray 2010; 20: 241-250.
11. Som S, D'Errico G, Longman D, Lucchini T,. Comparison and standardization of numerical approaches for the prediction of non-reacting and reacting diesel sprays. SAE technical paper 2012-01-1263, 2012.
12. Bosch W., The fuel rate indicator: a new instrument for display of the characteristic of individual injection. SAE technical paper 660749, 1966.
13. Payri R, Salvador FJ, Gimeno J, Bracho G., A new methodology for correcting the signal cumulative phenomenon on injection rate measurements. Exp Tech 2008; 15: 46-49.
14. Coppo M, Dongiovanni C., Experimental validation of a common-rail injector model in the whole operation field. J Eng Gas Turb Power 2007; 129: 596-608.
15. Chung NH, Oh BH, Sunwoo MH., Modelling and injection rate estimation of common-rail injectors for direct-injection diesel engines. Proc IMechE, Part D: J Automobile Engineering 2008; 222: 1089-1101.
16. Payri R, Tormos B, Salvador FJ, Plazas AH., Using one-dimensional modelling codes to analyse the influence of diesel nozzle geometry on injection rate characteristics. Int J Vehicle Des 2005; 38: 58-78.
17. Catania AE, Ferrari A, Manno M, Spessa E., Thermal effect simulation in high-pressure injection system transient flows. SAE technical paper 2004-01-0532, 2004.
18. Payri R, Salvador FJ, Gimeno J, García A., Flow regime effects over non-cavitating diesel injection nozzles. Proc IMechE, Part D: J Automobile Engineering 2012; 226: 133-144.
19. Payri R, Gimeno J, Venegas O, Plazas AH,. Effect of partial needle lift on the nozzle flow in diesel fuel injectors. SAE technical paper 2011-01-1827, 2011.
20. Plazas A., Modelado unidimensional de inyectores common-rail diesel. PhD Thesis, Universitat Politècnica de València (UPV), Valencia, 2005.
21. Karimi K., Characterization of multiple-injection diesel sprays at elevated pressures and temperatures. PhD Thesis, University of Brighton, Brighton, 2007.
22. LMS Imagine. Lab AMEsim v. 11: user's manual, France, 2011.
23. Ahlin K., Modeling of pressure waves in the common rail diesel injection system. Master's Thesis, Linköping University, Linköping, 2000.
24. Gauthier C, Sename O, Dugard L, Meissonnier G,. Modelling of a diesel engine common rail injection system. In: Proceedings of the 16th IFAC World Congress 2005, vol. 16, part 1, Prague, 4-8 June 2005.
25. Lopes A, Talavera-Prieto M, Ferreira A, Santos J, Santos M, Portugal A., Speed of sound in pure fatty acid methyl esters and biodiesel fuels. Fuel 2014; 116: 242-254.
26. Payri R, Salvador FJ, Gimeno J, Bracho G., The effect of temperature and pressure on thermodynamic properties of diesel and biodiesel fuels. Fuel 2011; 90: 1172-1180.
27. 2 emissions. Procedia: Soc Behav Sci 2012; 48: 2295-2314.
28. Pohorelsky L, Brynych P, Macek J, Vallaude P-Y, Ricaud J-C, Obernesser P, Tribotté P,. Air system conception for a downsized two-stroke diesel engine. SAE technical paper 2012-01-0831, 2012.
29. Benajes J, Molina S, Novella R, De Lima D., Implementation of the Partially Premixed Combustion concept in a 2-stroke HSDI diesel engine fueled with gasoline. Appl Energy 2014; 122: 94-111.
30. d'Ambrosio S, Ferrari A., Diesel injector cooking: optical-chemical analysis of deposits and influence on injected flow-rate, fuel spray and engine performance. J Eng Gas Turb Power 2012; 134 (6): 062801.