Numerical optimization of the Minimum Quantity Lubrication parameters by inner canalizations and cutting conditions for milling finishing process with Taguchi method

Journal of Cleaner Production

Volumn 108, Issue , 2015, Pages 65-71

  Duchosal, A ^a   Serra, R ^b   Leroy, R ^c   Hamdi, H ^a  

^a UNIVERSITÉ DE LYON   (France)

^b INSA CENTRE VAL DE LOIRE   (France)

^c Université Franc ois Rabelais de Tours   (France)

Author keywords

Computational fluid dynamics; Inner canalization geometries; Lagrangian multiphase flow; Minimum quantity lubrication; Surfacing tool; Taguchi method

Indexed keywords

CARBIDES; COMPUTATIONAL FLUID DYNAMICS; CUTTING; CUTTING TOOLS; DESIGN OF EXPERIMENTS; NUMERICAL METHODS; OPTIMIZATION; PARTICLE SIZE; PARTICLE SIZE ANALYSIS; TAGUCHI METHODS;

ENVIRONMENTAL-FRIENDLY; LAGRANGIAN; LUBRICATION PERFORMANCE; MINIMUM QUANTITY LUBRICATION; NUMERICAL OPTIMIZATIONS; OPTIMAL COMBINATION; TOOL-CHIP CONTACT AREA; TOOL/CHIP INTERFACE;

LUBRICATION;

EID: 84946481884     PISSN: 09596526     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jclepro.2015.07.126     Document Type: Article

References (25)

1. T. Aoyama Development of a mixture supply system for machining with minimal quantity lubrication CIRP Ann. - Manuf. Tech. 51 2002 289 292
2. S. Bahi, M. Nouari, A. Moufki, M. El Monsori, and A. Molinari A new friction law for sticking and sliding contacts in machining Trib. Int. 44 2011 764 771
3. S.W. Bouzid, N. Ben Salah, and J.L. Lebrun Influence of machining by finishing milling on surface characteristics Int. J. Mach. Tools Manuf. 41 2001 443 450
4. M.H. Cetin, B. Ozcelik, E. Kuram, and E. Demirbas Evaluation of vegetable based cutting fluids with extreme pressure and cutting parameters in turning of AISI 304L by Taguchi method J. Clean. Prod. 19 2011 2049 2056
5. W.G. Cochran, and G. Cox Experimental Design 1962 Asia Publishing House
6. S. Debnath, M.M. Reedy, and Q.S. Yi Environmental friendly cutting fluids and cooling techniques in machining: a review J. Clean. Prod. 83 2014 1 15
7. N.R. Dhar, M.W. Islam, and M.A.H. Mithu The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI 1040 steel J. Mat. Proc. Tech. 171 2006 93 99
8. A. Duchosal, R. Leroy, L. Vecellio, C. Louste, and N. Ranganathan An experimental investigation on oil mist characterization used in MQL milling process Int. J. Adv. Manuf. Tech. 66 2013 1003 1014
9. A. Duchosal, R. Serra, and R. Leroy Static numerical simulation of oil mist particle size effects on a range of internal channel geometries of a cutting tool used in MQL strategy Int. J. Eng. Sci. Innov. Tech. 1 2 2014 43 59
10. A. Duchosal, R. Serra, and R. Leroy Numerical study of the inner canalization geometry optimization in a milling tool used in micro quantity lubrication Mech. Ind. 15 2014 435 442
11. 3 engineering ceramics J. Clean. Prod. 66 2014 632 643
12. 3 J. Clean. Prod. 19 2011 640 645
13. J.A. Ghani, I.A. Choudhury, and H.H. Hassan Application of Taguchi method in the optimization of end milling parameters J. Mat. Proc. Tech. 145 2004 84 92
14. M. Hadad, and B. Sadeghi Minimum quantity lubrication-MQL turning of AISI steel alloy J. Clean. Prod. 54 2013 332 343
15. S.A. Iqbal, P.T. Mativenga, and M.A. Sheikh A comparative study of the tool-chip contact length in turning of two engineering alloys for a wide range of cutting speeds Int. J. Adv. Manuf. Tech. 42 2009 30 40
16. S. Jozic, D. Bajic, and L. Celent Application of compressed cold air cooling: achieving multiple performance characteristics in end milling process J. Clean. Prod. 100 2015 325 332
17. P. Kalita, A.P. Malshe, S.A. Kumar, V.G. Yognath, and T. Gurumurthy Study of specific energy and friction coefficient in minimum quantity lubrication grinding using oil-based nanolubricants J. Manuf. Proc. 14 2012 160 166
18. Y. Kamata, and T. Obikawa High speed MQL finish turning of Inconel 718 with different coated tools J. Mat. Proc. Tech. 192 2007 281 286
19. L.N. Lopez de Lacalle, C. Angulo, A. Lamikiz, and J.A. Sanchez Experimental and numerical investigation on the effect of spray cutting fluids in high speed milling J. Mat. Proc. Tech. 172 2006 11 15
20. M. Rahman, A. Senthil Kumar, and M.U. Salam Experimental evaluation on the effect of minimal quantities of lubricant in milling Int. J. Mach. Tools Manuf. 42 2002 539 547
21. K. Simunovic, G. Simunovic, and T. Saric Single and multiple goal optimization of structural steel face milling process considering different methods of cooling/lubricating J. Clean. Prod. 94 2015 321 329
22. D.A. Stephenson Assessment of steady-state metal cutting temperature models based on simultaneous infrared and thermocouple data J. Eng. Ind. 113 1991 121 128
23. C.D. Wang, K. Li, M. Chen, and Z.Q. Liu Evaluation of minimum quantity lubrication effects by cutting force signals in face milling of Inconel 182 overlays J. Clean. Prod. 108 2015 145 157
24. R.P. Zeilmann, and W.L. Weingaertner Analysis of temperature during drilling of Ti6A14V with minimal quantity of lubricant Int. J. Mach. Tools Manuf. 179 2006 124 127
25. S. Zhang, J.F. Li, and Y.W. Wang Tool life and cutting forces in end milling Inconel 718 under dry and minimum quantity cooling lubrication cutting conditions J. Clean. Prod. 32 2012 81 87