The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel

Journal of Materials Processing Technology

Volumn 171, Issue 1, 2006, Pages 93-99

  Dhar, N R ^a   Islam, M W ^a   Islam, S ^a   Mithu, M A H ^b  

^a BANGLADESH UNIVERSITY OF ENGINEERING AND TECHNOLOGY   (Bangladesh)

^b SHAHJALAL UNIVERSITY OF SCIENCE AND TECHNOLOGY   (Bangladesh)

Author keywords

Chip; Cutting temperature; Dimensional deviation; MQL; Steel; Turning

Indexed keywords

CUTTING FLUIDS; LUBRICATION; METAL ANALYSIS; QUALITY CONTROL; TURNING;

CHIP; CUTTING TEMPERATURE; DIMENSIONAL DEVIATION; MINIMUM QUANTITY OF LUBRICATION (MQL);

STEEL STRUCTURES;

EID: 29144506115     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2005.06.047     Document Type: Article

References (19)

1. M.C. Shaw, J.D. Pigott, and L.P. Richardson Effect of cutting fluid upon chip-tool interface temperature Trans. ASME 71 1951 45 56
2. S. Paul, N.R. Dhar, and A.B. Chattopadhyay Beneficial effects of cryogenic cooling over dry and wet machining on tool wear and surface finish in turning AISI-1060 steel Proceedings of the ICAMT-2000 Malaysia 2000 209 214
3. C. Cassin, and G. Boothroyed Lubrication action of cutting fluids J. Mech. Eng. Sci. 7 1 1965 67 81
4. M. Mazurkiewicz, Z. Kubala, and J. Chow Metal machining with high pressure water-jet cooling assistance - a new possibility J. Eng. Ind. 111 1989 7 12
5. A. Alaxender, A.S. Varadarajan, and P.K. Philip Hard turning with minimum cutting fluid: a viable green alternative on the shop floor Proceedings of the 18th AIMTDR 1998 152 155
6. M. Sokovic, and K. Mijanovic Ecological aspects of the cutting fluids and its influence on quantifiable parameters of the cutting processes J. Mater. Process. Technol. 109 12 2001 181 189
7. F. Klocke, and G. Eisennblatter Dry cutting Ann. CIRP 46 2 1997 519 526
8. G. Byrne, and E. Scholta Environmentally clean machining processes - a strategic approach Ann. CIRP 42 1 1993 471 474
9. F. Klocke, and G. Eisenblatter Coated tools for metal cutting-features and applications Ann. CIRP 48 2 1999 515 525
10. U. Heisel, and M. Lutz Application of minimum quantity cooling lubrication technology in cutting processes Prod. Eng. II 1 1994 49 54
11. J.W. Sutherland An experimental investigation of air quality in wet and dry turning Ann. CIRP 49 1 2000 61 64
12. S. Suda Evaluation of machinability with MQL system and effectiveness in production lines Proceedings of the Int. Tri. Conf. Nagasaki, 2000 2001 203 208
13. J. McCabe, and M.A. Ostaraff Performance experience with near-dry machining of aluminum Lubr. Eng. 2001 22 27
14. T.F. MaClure, R. Adams, M.D. Gugger, Comparison of flood vs. microlubrication on machining performance, Internet: http://www.unist.com/techsolve.html.
15. H.K. Tönshoff, and W. Spintig Machining of holes developments in drilling technology Ann. CIRP 1994 551 561
16. E. Lugscheider, O. Knotek, C. Barimani, T. Leyendecker, O. Lemmer, and R. Wenke Investigations on hard coated reamers in different lubricant free cutting operations Surf. Coat. Technol. 90 1997 172 177
17. D.U. Braga, A.E. Diniz, G. Miranda, and N.L. Coppini Minimal lubrication in the drilling process of aluminum-silicon alloy-A356 (SAE 323) Proceedings of the Third International Machining and Grinding Conference (SME), vol. 1 Cincinnati, USA 1999 683 697
18. K.M. Rahman, Effect of minimum quantity lubrication (MQL) in drilling commercially used steels, M. Eng. Dissertation, BUET, Bangladesh, 2004.
19. M.W. Islam, Experimental study of effect of minimum quantity lubrication (MQL) in turning AISI-1040 steel, M. Eng. Dissertation, BUET, Bangladesh, 2004.