Influence of controller parameters on the life of ball screw feed drives

Advances in Mechanical Engineering

Volumn 7, Issue 8, 2015, Pages 1-11

  Mauro, Stefano ^a   Pastorelli, Stefano ^a   Johnston, Edward ^a  

^a POLITECNICO DI TORINO   (Italy)

Author keywords

ball screw; dynamic simulation; fatigue life; Machine tool; position control

Indexed keywords

EID: 84940943525     PISSN: 16878132     EISSN: 16878140     Source Type: Journal    
DOI: 10.1177/1687814015599728     Document Type: Article

References (17)

1. Altintas Y, Verl A, Brecher C,. Machine tool feed drives. CIRP Ann: Manuf Techn 2011; 60: 779-796.
2. Fleischer J, Broos A, Schopp M,. Lifecycle-oriented component selection for machine tools based on multibody simulation and component life prediction. CIRP J Manuf Sci Technol 2009; 1: 179-184.
3. Verl A, Frey S,. Correlation between feed velocity and preloading in ball screw drives. CIRP Ann: Manuf Techn 2010; 59: 429-432.
4. Wei C-C, Liou W-L, Lai R-S,. Wear analysis of the offset type preloaded ball-screw operating at high speed. Wear 2012; 292-293: 111-123.
5. Verl A, Frey S, Heinke T,. Double nut ball screw with improved operating characteristics. CIRP Ann: Manuf Techn 2014; 63: 361-364.
6. ISO 3408-5:2006. Ball screws, part 5, static and dynamic axial load ratings and operational life.
7. Frey S, Walther M, Verl A,. Periodic variation of preloading in ball screws. Prod Eng Res Devel 2010; 4: 261-267.
8. Hung J-P, Wu JS-S, Chiu JY,. Impact failure analysis of re-circulating mechanism in ball screw. Eng Fail Anal 2004; 11: 561-573.
9. Fleischer J, Leberle U, Maier J,. Resource-efficient ball screw by adaptive lubrication. Procedia CIRP 2014; 15: 50-55.
10. Mauro S, Pastorelli S, Mohtar T,. Sensitivity analysis of the transmission chain of a horizontal machining tool axis to design and control parameters. Adv Mech Eng 2014; 6: 169064.
11. Haschke R, Weitnauer E, Ritter H,. On-line planning of time-optimal, jerk-limited trajectories. In: IEEE/RSJ international conference on intelligent robots and systems, Nice, 22-26 September 2008, pp. 3248-3253. New York: IEEE.
12. Béarée R, Olabi A,. Dissociated jerk-limited trajectory applied to time-varying vibration reduction. Robot Cim Int Manuf 2013; 29: 444-453.
13. Sepasi D, Nagamune R, Sassani F,. Tracking control of flexible ball screw drives with runout effect and mass variation. IEEE T Ind Electron 2012; 59: 1248-1256.
14. Symens W, Van Brussel H, Sweversl J,. Gain-scheduling control of machine tools with varying structural flexibility. CIRP Ann: Manuf Techn 2004; 53: 321-324.
15. Mohammad A, Uchiyama N, Sano S,. Reduction of electrical energy consumed by feed-drive systems using sliding-mode control with a nonlinear sliding surface. IEEE T Ind Electron 2014; 61: 2875-2882.
16. Dong L, Tang W,. Control of ball screw drives using adaptive backstepping sliding mode controller and minimum tracking error prefilter. In: 11th IEEE international conference on control & automation (ICCA), Taichung, Taiwan, 18-20 June 2014, pp. 995-1000. New York: IEEE.
17. Yan MT, Huang YL, Hsue AW-J,. Friction compensation of a retrofit milling machine through a fuzzy logic controller combined with neural network-based feedforward control. In: IEEE international conference on mechatronics (ICM 2005), Taipei, Taiwan, 10-12 July 2005, pp. 398-403. New York: IEEE.