Predictive modeling of residual stress in minimum quantity lubrication machining

International Journal of Advanced Manufacturing Technology

Volumn 70, Issue 9-12, 2014, Pages 2159-2168

  Ji, Xia ^a   Zhang, Xueping ^a   Liang, Steven Y ^b  

^a SHANGHAI JIAO TONG UNIVERSITY   (China)

^b GEORGIA INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

Analytical modeling; Minimum quantity lubrication; Residual stress

Indexed keywords

APPLICATION PARAMETERS; BOUNDARY LUBRICATIONS; LUBRICATION CONDITION; MINIMUM QUANTITY LUBRICATION; PROCESSING CONDITION; RESIDUAL STRESS PREDICTION; STRAIN COMPATIBILITY; THERMAL-MECHANICAL MODELING;

AIR LUBRICATION; ANALYTICAL MODELS; CUTTING; TOOLS; TURNING;

RESIDUAL STRESSES;

EID: 84896719820     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-013-5439-2     Document Type: Article

References (27)

1. Machado A, Wallbank J (1997) The effect of extremely low lubricant volumes in machining. Wear 210(1):76-82
2. Rahman M, Senthil Kumar A, Salam M (2002) Experimental evaluation on the effect of minimal quantities of lubricant in milling. Int J Mach Tools Manuf 42(5):539-547
3. Yasir A, Che Hassan C, Jaharah A, Norhamidi M, Gusri A, Zaid A (2010) Cutting force analysis when milling Ti-6Al-4V under dry and near dry conditions using coated tungsten carbides. Adv Mater Res 129:993-998
4. Dhar N, Islam M, Islam S, Mithu M (2006) The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel. J Mater Process Technol 171(1):93-99
5. Morgan MN, Barczak L, Batako A (2012) Temperatures in fine grinding with minimum quantity lubrication (MQL). Int J Adv Manuf Technol 60(9-12):951-958
6. Mao C, Tang XJ, Zou HF, Zhou ZX, Yin WW (2012) Experimental investigation of surface quality for minimum quantity oil-water lubrication grinding. Int J Adv Manuf Technol 59(1-4):93-100
7. Hwang YK, Lee CM (2010) Surface roughness and cutting force prediction in MQL and wet turning process of AISI 1045 using design of experiments. J Mech Sci Technol 24(8):1669-1677
8. Liu Z, Cai X, Chen M, An Q (2011) Investigation of cutting force and temperature of end-milling Ti-6Al-4V with different minimum quantity lubrication (MQL) parameters. Proc Inst Mech Eng B J Eng Manuf 225(8):1273-1279
9. Wang Z, Rahman M, Wong Y, Neo K, Sun J, Tan C, Onozuka H (2009) Study on orthogonal turning of titanium alloys with different coolant supply strategies. Int J Adv Manuf Technol 42(7):621-632
10. Thakur D, Ramamoorthy B, Vijayaraghavan L (2010) Investigation and optimization of lubrication parameters in high speed turning of superalloy Inconel 718. Int J Adv Manuf Technol 50(5-8):471-478
11. Maekawa K (1998) Computational aspects of tribology in metal machining. Proc Inst Mech Eng J J Eng Tribol 212(4):307-318
12. Childs T, Maekawa K, Maulik P (1988) Effects of coolant on temperature distribution in metal machining. Mater Sci Technol 4(11):1006-1019
13. Li K-M, Liang SY (2007) Modeling of cutting forces in near dry machining under tool wear effect. Int J Mach Tools Manuf 47(7):1292-1301
14. Li K, Liang S (2006) Modeling of cutting temperature in near dry machining. J Manuf Sci Eng 128:416-424
15. Umbrello D, Ambrogio G, Filice L, Shivpuri R (2007) An ANN approach for predicting subsurface residual stresses and the desired cutting conditions during hard turning. J Mater Process Technol 189(1):143-152
16. Li X (1996) Study of the jet-flow rate of cooling in machining Part 1. Theoretical analysis. J Mater Process Technol 62(1):149-156
17. Khan M, Mithu M, Dhar N (2009) Effects of minimum quantity lubrication on turning AISI 9310 alloy steel using vegetable oil-based cutting fluid. J Mater Process Technol 209(15):5573-5583
18. Ji X, Zhang X, Liang SY (2012) A new approach to predict machining force and temperature with minimum quantity lubrication. Proceedings of the ASME 2012 International Manufacturing Science and Engineering Conference (MSEC 2012), June 4-8, 2012, Notre Dame, Indiana, USA
19. Waldorf DJ, DeVor RE, Kapoor S (1998) Slip-line field for ploughing during orthogonal cutting. J Manuf Sci Eng Trans ASME 120(4):693-698
20. Kato S, Marui E, Hashimoto M (1998) Fundamental study on normal load dependency of friction characteristics in boundary lubrication. Tribol Trans 41(3):341-349
21. Oxley PLB (1989) The mechanic of machining - an analytical approach to assessing machinability. Ellis Horwood, Chichester, p 37
22. Su J-C, Young KA, Ma K, Srivatsa S, Morehouse JB, Liang SY (2013) Modeling of residual stresses in milling. Int J Adv Manuf Technol 65:717-733
23. Johnson KL (1987) Contact mechanics. Cambridge University Press, New York, p19
24. Jiang Y, Sehitoglu H (1994) An analytical approach to elastic-plastic stress analysis of rolling contact. J Tribol 116(3):577-587
25. McDowell D (1997) An approximate algorithm for elastic-plastic two-dimensional rolling/sliding contact. Wear 211(2):237-246
26. McDowell D, Moyar G (1986) A more realistic model of nonlinear material response: application to elastic-plastic rolling contact. In: Proceedings of the 2nd International Symposium on Contact Mechancis and Wear of Rail/Wheel Systems
27. Merwin J, Johnson K (1963) An analysis of plastic deformation in rolling contact. P I Mech Eng 177(1):676-690