Investigation and optimization of lubrication parameters in high speed turning of superalloy Inconel 718

International Journal of Advanced Manufacturing Technology

Volumn 50, Issue 5-8, 2010, Pages 471-478

  Thakur, Dinesh G ^a   Ramamoorthy, B ^a   Vijayaraghavan, L ^a  

^a INDIAN INSTITUTE OF TECHNOLOGY MADRAS   (India)

Author keywords

ANOVA; Force; Inconel 718; MQL under pulsed jet mode; Temperature; Wear

Indexed keywords

ANOVA; FORCE; INCONEL 718; MQL UNDER PULSED JET MODE; WEAR;

ANALYSIS OF VARIANCE (ANOVA); LUBRICATION; OPTIMIZATION; SUPERALLOYS; TURNING;

CUTTING FLUIDS;

EID: 78650302819     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-010-2538-1     Document Type: Article

References (19)

1. Klocke F (1997) Dry cutting. Annals of the CIRP 46(2):519-526
2. Klocke F, Eisenblatter G (1997) Machinability investigation of the drilling process using minimal cooling lubrication techniques. Annals of the CIRP 46(1):19-24
3. Popke H, Emmer Th, Steffenhagen J (1999) Environmentally clean metal cutting processes-machining on the way to dry cutting. Proc Inst Mech Eng (Part B) 213:329-332
4. Weinert K, Inasaki I, Sutherland JW, Wakabayashi T (2004) Dry Mach Min Quant Lubrication CIRP Annals-Manuf Technol 53 (2):511-537
5. Kelly JF, Cotterell MG (2002) Minimal lubrication machining of aluminium alloys. J Mater Process Technol 120:327-334
6. Dudzinski D, Devillez A, Moufki A, Larrouquère D, Zerrouki V, Vigneau J (2004) A review of developments towards dry and high speed machining of Inconel 718 alloy. Int J Mach Tools Manuf 44 (4):439-456
7. Davim JP, Sreejith PS, Gomes R, Peixoto C (2006) Experimental studies on drilling of aluminium (AA1050) under dry, minimum quantity of lubricant, and flood-lubricated conditions. Proc ImechE Part B: J Eng Manuf 220:1605-1611
8. Heinemann R, Hinduja S, Barrow G, Petuelli G (2006) Effect of MQL on the tool life of small twist drills in deep-hole drilling. Int J Mach Tool Manuf 46:1-6 (Pubitemid 41497894)
9. Machado AR, Wallbank J (1997) The effect of extremely low lubricant volumes in machining. Wear 219:76-82
10. Rahman M, Kumar AS, Manzoor-Ul-Salam A (2001) Evaluation of minimal quantities of lubricant in end milling. Int J Adv Manuf Technol 18:235-241
11. Lugscheider E, Knotek O, Barimani C, Leyendecker T, Lemmer O, Wenke R (1997) Investigations on hard coated reamers in different lubricant free cutting operations. Surf Coat Technol 90:172-177
12. Dhar NR, Islam MW, Islam S, Mithu MAH (2006) The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel. J Mater Process Technol 171:93-99
13. Braga DAE, Miranda GWA, Coppini NL (2002) Using a minimum quantity of lubricant (MQL) and a diamond coated tool in the drilling of aluminum-silicon alloys. J Mater Process Technol 122:127-138
14. Davim JP, Sreejith PS, Silva J (2007) Turning of brasses using minimum quantity of lubricant (MQL) and flooded-lubricant conditions. Mater Manuf Process 22:45-50
15. Varadarajan AS, Philip PK, Ramamoorthy B (2002) Investigations on hard turning with minimal cutting fluid application (HTMF) and its comparison with dry and wet turning. Int J Mach Tools Manuf 42:193-200
16. Sadeghi MH, Haddad MJ, Tawakoli T, Emami M (2009) Minimal quantity lubrication-MQL in grinding of Ti-6Al-4V titanium alloy. Int J Adv Manuf Technol 44(5-6):487-500
17. Li K-M, Steven YL (2007) Performance profiling of minimum quantity lubrication in machining. Int J Adv Manuf Technol 5(3-4): 226-233
18. Phillip JR (1989) Taguchi techniques for quality engineering. McGraw-Hill, New York
19. Madhav SP (1989) Quality Engineering using robust design. Printice Hall, New Jersey