Modeling of cutting temperature in near dry machining

Journal of Manufacturing Science and Engineering

Volumn 128, Issue 2, 2006, Pages 416-424

  Li, Kuan Ming ^a   Liang, Steven Y ^a  

^a GEORGIA INSTITUTE OF TECHNOLOGY   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

COOLING; CUTTING; FLUIDS; HEAT LOSSES; INTERFACES (MATERIALS); LUBRICATION; MACHINE TOOLS; THERMOCOUPLES;

CUTTING TEMPERATURE; DRY MACHINING; FLOW RATES; LUBRICATING EFFECTS;

MACHINING;

EID: 33745446252     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2162907     Document Type: Article

References (29)

1. Taylor, F. W., 1907, "On the Art of Cutting Metals." Trans. ASME, 28, pp. 31-248.
2. Jaeger. J. C., 1942, "Moving Sources of Heat and the Temperatures at Sliding Contacts," J. Proc. R. Soc. N. S. W., 76, pp. 203-224.
3. Hahn, R. S., 1951, "On the Temperature Developed at the Shear Plane in the Metal Cutting Process," Proc. of First U.S. National Congress of Applied mechanics, pp. 661-666.
4. Chao, B. T., and Trigger, K. J., 1953, "Significance of Thermal Number in Metal Machining," Trans. ASME, 75(1), pp. 109-115.
5. Loewcn, E. G., and Shaw, M. C., 1954, "On Analysis of Cutting-Tool Temperatures," Trans. ASME, 76(2), pp. 217-225.
6. Carslaw, H. S., and Jaeger, J. C., 1959, Conduction of Heat in Solids. Oxford University Press, Oxford.
7. Komanduri. R., and Hou, Z. B., 2001 "Thermal Modeling of the Metal Cutting Process Part III-Temperature Rise Distribution Due to the Combined Effects of Shear Plane Heat Source and the Tool-Chip Interface Frictional Heat Source," Int. J. Mech. Sci., 43, pp. 89-107.
8. Huang, Y., and Liang. S. Y., 2002, "Modeling of the Cutting Temperature Distribution Under the Tool Flank Wear Effect," Proc. Inst. Mech. Eng., Part C: J. Mech. Eng. Sci., 217(11), pp. 1195-1208.
9. Li, X., 1995, "Effect of Coolant Flow Rate on Cooling in Machining," Technical Paper - Society of Manufacturing Engineers MR, pp. 109-114.
10. Childs, T. H. C., Maekawa, K., and Maulik, P., 1988, "Effects of Coolant on Temperature Distribution in Metal Cutting," Meas. Sci. Technol., 4, pp. 1006-1019.
11. Dhar, N. R., Paul, S., and Chattopadhyay, A. B., 2002, "Role of Cryogenic Cooling on Cutting Temperature in Turning Steel," ASME J. Manuf. Sci. Eng., 124, pp. 146-154.
12. Klocke, F., and Eisenblatter, G., 1997, "Dry Cutting," CIRP Ann., 46(2), pp. 519-526.
13. Machado, A. R., and Wallbank, J., 1997, "The Effect of Extremely Low Lubricant Volumes in Machining," Wear, 210, pp. 76-82.
14. Braga, D. U., Diniz, A. E., Miranda, G. W. A., and Coppini, N. L., 2002, "Using a Minimum Quantity of Lubricant (MQL) and a Diamond Coated Tool in the Drilling of Aluminum-Silicon Alloys," J. Mater. Process. Technol., 122(1), pp. 127-138.
15. Varadarajan, A. S., Philip, P. K., and Ramamoorthy, B., 2002, "Investigations on Hard Turning With Minimal Cutting Fluid Application (HTMF) and Us Comparison With Dry and Wet Turning," Int. J. Mach. Tools Manuf., 42, pp. 193-200.
16. Wakabayashi, T., Inasaki, I., Suda, S., and Yokota, H., 2003, "Tribological Characteristics and Cutting Performance of Lubricant Esters for Semi-Dry Machining," CIRP Ann., 52(1), pp. 61-64.
17. Um, J.-Y., Chow, L. C., and Jawahir, I. S., 1995, "Experimental Investigation of the Application of the Spray Cooling Method in Stainless Steel Machining," ASME Manufacturing Engineering Division, MED, Manufacturing Science and Engineering, ASME, New York, 2-1, pp. 165-178.
18. Rahman, M., Kumar, A. S., and Salam, M. U., 2002, "Experimental Evaluation on the Effect of Minimal Quantities of Lubricant in Milling," Int. J. Mach. Tools Manuf., 42(5), pp. 539-547.
19. Weinert, K., Inasaki, I., Sutherland, J. W., and Wakabayashi, T., 2005, "Dry Machining and Minimum Quantity Lubrication," CIRP Ann., 53(2), pp. 511-537.
20. Oxley, P. L. B., 1989, Mechanics of Machining, an Analytical Approach to Assessing Machinability, Ellis Horwood Limited, West Sussex.
21. Komanduri, R., and Hou, Z. B., 2000, "Thermal Modeling of the Metal Cutting Process Part I - Temperature Rise Distribution Due to Shear Plane Heat Source," Int. J. Mech. Sci., 42, pp. 1715-1752.
22. Komanduri, R., and Hou, Z. B., 2001, "Thermal Modeling of the Metal Cutting Process Part II - Temperature Rise Distribution Due to Frictional Heal Source at the Tool-Chip Interface," Int. J. Mech. Sci., 43, pp. 57-88.
23. Keith, F., and Bonn, M. S., 1997, Principle of Heat Transfer. PWS, Boston.
24. Munson, B. R., Young, D. F., and Okiishi, T. H., 2001. Fundamentals of Fluid Mechanics, Wiley, New York.
25. Wu, C.-F. and Hamada, M., 2000, Experiments: Planning, Analysis, and Parameter Design Optimization, Wiley, New York.
26. Shaw, M. C., 1984, Metal Cutting Principles, Oxford University Press. New York.
27. Merchant, M. E., 1945, "Mechanics of the Metal Cutting Process, Pan 2: Plasticity Conditions in Orthogonal Cutting," J. Appl. Phys., 16(6), pp. 318-324.
28. ASM Handbook, 1992, ASM International, Metals Park, OH.
29. Shackelford, J. F., Alexander, W., and Park, J. S., 1994, CRC Materials Science and Engineering Handbook, CRC Press, Boca Raton.