Transmission and gearbox noise and vibration prediction and control

16th International Congress on Sound and Vibration 2009, ICSV 2009

Volumn 8, Issue , 2009, Pages 5056-5071

  Tuma, Jiri ^a  

^a VSB TECHNICAL UNIVERSITY OF OSTRAVA   (Czech Republic)

Author keywords

[No Author keywords available]

Indexed keywords

ANALYTICAL METHOD; COMPUTER BASED TOOLS; GEAR DESIGN; GEAR NOISE; MESH CYCLE; NOISE AND VIBRATION; NOISE LEVELS; NOISE PROBLEMS; PRACTICAL ENGINEERING PROBLEMS; RADIATED NOISE; SELF-EXCITED VIBRATIONS; SOUND PRESSURE LEVEL; TIME AND FREQUENCY DOMAINS; TRANSMISSION ERROR;

ACOUSTIC NOISE MEASUREMENT; FREQUENCY DOMAIN ANALYSIS; NOISE POLLUTION; SIGNAL PROCESSING; VIBRATION ANALYSIS;

ACOUSTIC NOISE;

EID: 84871421497     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: None     Document Type: Conference Paper

References (19)

1. R. Randall, Noise and vibration data analysis. In: M. Crocker (Editor) Handbook of noise and vibration control. New York: Wiley, 2007. Chapter 46, pp. 549-564.
2. J. Tuma, Transmission and gearbox noise and vibration prediction and control. In: M. Crocker (Editor) Handbook of noise and vibration control. New York: Wiley, 2007. Chapter 88, pp. 1080-1089.
3. D. Houser, Gear noise and vibration prediction and control methods. In: M. Crocker (Editor) Handbook of noise and vibration control. New York: Wiley, 2007. Chapter 69, pp. 847-856.
4. T. Elnady, Effect of Machine defects on its radiated noise. In: Proceedings of Tenth international congress on sound and vibration (ICSV10). Stockholm, July 7-10, 2003, pp. 4021-4028.
5. J. I. Taylor, The Gear Analysis Handbook, Vibration Consultants, Inc., USA, 2000
6. J. Tuma, Dedopplerisation in Vehicle External Noise Measurements. In: Proceedings of Eleventh international congress on sound and vibration (ICSV11). St. Petersburg, July 5-8, 2004, pp. 151-158.
7. H. Vold and J. Leuridan, High Resolution Order Tracking at Extreme Slew Rates, Using Kalman Tracking Filter, SAE Paper 931288, 1993
8. P. D. McFadden, "Detecting Fatigue Cracks in Gears by Amplitude and Phase Demodulation of the Meshing Vibration". ASME J. of Vib. Acous. Stress and Rel. in Des., April 1986, Vol. 108, pp. 165-170.
9. M. Angelo, Vibration Monitoring of Machines. Brüel & Kjær Technical Review, No. 1, 1987.
10. J. Tuma, R. Kubena, V. Nykl, Assessment of Gear Quality Considering the Time Domain Analysis of Noise and Vibration Signals. In: Proceedings of 1994 Gear International Conference. Newcastle, September 1994, pp.463-468.
11. Ch-H. Chung, G. Steyer, T. Abe, M. Clapper, Ch. Shah, Gear Noise Reduction through Transmission Error Control and Gear Blank Dynamic Tuning, SAE Paper 1999-01-1766.
12. D.B. Welbourn, Fundamental knowledge of gear noise - A survey, In: Proceedings Noise & Vib. Of. Eng. And Trans., I Mech E, -14, (1979).
13. D. J. Smith, Gear Noise and Vibration, 1st ed., Marcel Dekker Inc., New York and Basel 1999.
14. M. Henriksson and M. Pärssinen, Comparison of Gear Noise and Dynamic Transmission Error Measurements. In: Proceedings of Tenth international congress on sound and vibration (ICSV10). Stockholm, July 7-10, 2003, pp. 4005-4012.
15. J. Tuma, Phase Demodulation of Impulse Signals in Machine Shaft Angular Vibration Measurements. In: Proceedings of Tenth international congress on sound and vibration (ICSV10). Stockholm, July 7-10, 2003, pp. 5005-5012.
16. V. Moravec, New toothing type in TATRA gearboxes with low noise and increased life time (in Czech). In: International conference ICESA 94, Praque, Czech Republic, 1994, pp. 5.
17. Z. Dejl, V. Moravec, Modification of Spur Involute Gearing. In: The Eleventh World Congress on Mechanism and Machine Science, Tianjin, China, April 1-4, 2004, pp. 782-786.
18. C. D. Begg, C. S. Byington, P. M. Kenneth, Dynamic Simulation of Mechanical Fault Transition, In: Proccedings of the 54th Meeting of the Society for Machinery Failure Prevention Technology, Virginia Beach, VA, May 1-4, 2000, pp. 203-212.
19. M. Hortel, A. Škuderová, To the influence of nonlinear damping on the bifurcation phenomena in gear mesh of one branch of power flow of the pseudoplanetary gear system. In Engineering Mechanics 2008 Svratka, May 12-15 2008.