Gear Noise and Vibration Prediction and Control Methods

Handbook of Noise and Vibration Control

Volumn , Issue , 2008, Pages 847-856

  Houser, Donald R ^a  

^a OHIO STATE UNIVERSITY   (United States)

Author keywords

Axial Shuttling Force and Friction Force; Gear noise and vibration paths; Load dependent sources; Low transmission error gear; Transmission error and mesh stiffness variation

Indexed keywords

EID: 84891288988     PISSN: None     EISSN: None     Source Type: Book    
DOI: 10.1002/9780470209707.ch69     Document Type: Chapter

References (28)

1. D. R. Houser, Gear Noise Sources and Their Prediction Using Mathematical Models, In Gear Design Manufacturing and Inspection Manual, Society of Automotive Engineers, Warrendale, PA, 1990, pp. 213-222.
2. R. W. Gregory, S. L. Harris, R. G. Munro, and Dynamic Behavior of Spur Gears, Proc. I. Mech. E, No. 8, April, 1953, pp. 207-226.
3. W. D. Mark, Gear Noise Excitation, Plenum, New York, 1982, pp. 55-93.
4. D. B. Welbourn, Fundamental Knowledge of Gear Noise-A Survey, Proc. Noise and Vibration of Engines and Transmissions, I. Mech. Eng. Aut. Div., July 1979, pp. 9-14.
5. G. Niemann and J. Baethge, Transmission Error, Tooth Stiffness and Noise of Spur and Helical Gears-Part 1, Vol. 112 (Drehwegfehler, Zahnfederharte und Gerausch bei Stirnradern), VDIZ, 1970.
6. J. Börner and D. R. Houser, Influence of Friction and Bending Moments on Gear Noise Excitations, SAE Noise and Vibration Conference and Exhibition, Paper 961816, Vol. 105 No. 6, 1996, pp. 1669-1676.
7. M. Vaishya and D. R. Houser, Modeling and Measurement of Sliding Friction for Gear Analysis, AGMA Fall Technical Meeting, Paper 99FTMS1, 1999.
8. D. R. Houser, F. B. Oswald, M. J. Valco, R. J. Drago, and J. W. Lenski, Comparison of Transmission Error Predictions with Noise Measurements for Several Spur and Helical Gears, Proc. 30th AIAA/ASME/SAE/ASEE Joint Propulsion Conference, 1994.
9. A. Kubo, T. Nonaka, N. Kato, S. Kato, and T. Ohmori Representative Form Accuracy of Gear Tooth Flanks on the Prediction of Vibration and Noise of Power Transmissions, Trans. JSME, Vol. 56, No. 532, pp. 238-243, AGMA Fall Technical Meeting, Paper 92FTM9, 1992.
10. R. E. Smith, The Relationship of Measured Gear Noise to Measured Gear Transmission Errors, AGMA Fall Technical Meeting, Paper 87FTM6, 1987.
11. J. D. Smith, Gears and Their Vibration, Macmillan, New York, 1983.
12. D. R. Houser and J. Harianto, The Effect of Micro-Geometry and Load on Helical Gear Noise Excitations, SAE Noise and Vibration Conference and Exhibition, Paper 2005-01-2295, 2005.
13. D. W. Dudley, Handbook of Practical Gear Design, McGraw Hill, New York, 1962.
14. R. Drago, J. Lenski, R. Spencer, M. Valco, and F. B. Oswald, The Relative Noise Levels of Parallel Axis Gear Sets with Various Contact Ratios and Gear Tooth Forms, AGMA Fall Technical Meeting, Paper 93FTM11, 1993.
15. T. F. Conry and A. Seireg, A Mathematical Programming Technique for the Evaluation of Load Distribution and Optimal Modifications for Gear Systems, J. Eng. Ind., Trans. ASME, Vol. 95, No. 4, November 1973, pp. 1115-1123.
16. D. R. Houser and J. Harianto, Load Distribution Program Reference Manual, GearLab, The Ohio State University, Columbus, OH, 2002.
17. A. Kubo, I. Tarutani, C. Gosselin, T. Nonaka, N. Aoyama, and Z.Wang, A Computer Based Approach for Evaluation of Operating Performances of Bevel and Hypoid Gears, JSME Int. J., Vol. 40, No. 4, 1997, pp. 749-758.
18. L. K. H. Lu, W. B. Rockwood, P. C. Werner, and R. G. Dejong, An Integrated Gear System Dynamics Analysis over a Broad Frequency Range, Shock and Vibration Bull., 55, Part 3, Shock and Vibration Information Center, 1985, pp. 1-11.
19. H. N. Özguven and D. R. Houser, Mathematical Models used in Gear Dynamics-A Review, J. Sound Vib., Vol. 121, No. 3, Mar. 1988, pp 383-411.
20. A. Kahraman and R. Singh, Interactions between Time-Varying Mesh Stiffness and Clearance Nonlinearity in a Gear System, J. Sound Vib., Vol. 146, 1991. pp. 135-156.
21. V. Kartik and D. R. Houser, An Investigation of Shaft Dynamic Effects on Gear Vibration and Noise Excitations, SAE Transaction, J. Passenger Car Mech. Syst., Paper 2003-01-1491, 2003.
22. M. Colabawala, J. Sorenson, and D. R. Houser, An Experimental Procedure for Characterization of Gear Whine Noise in a Variety of Applications, SAE Noise and Vibration Conference and Exhibition, Paper 2003-01-1488, 2003.
23. R. Singh, Dynamic Design of Powertrains for Reduced Vibro-Impacts, Optimum Dynamic Design, 1997, pp. 305-317.
24. D. R. Houser and P. Biggert, Gear Ghost Noise-A Case History Using Single Flank Transmission Error Measurements, Proc. NOISECON 91, Tarrytown, NY, 1991, pp. 95-102.
25. W. D. Mark, Contributions to the Vibratory Excitation of Gear Systems from Periodic Undulation on Tooth Running Surfaces, J. Acoust. Soc. Am., Vol. 91, No. 1, 1992, pp. 166-186.
26. D. R. Houser and J. Harianto, Design Robustness and Its Effect on Transmission Error and Other Design Parameters, The International Conference on Mechanical Transmission, 2001; also in Gear Tech. Mag., J. Gear Manufact., March/April 2003, pp. 18-25.
27. D. R. Houser, Gear Noise, in Dudley's Gear Handbook, D. Townsend, Ed., McGraw Hill, New York; 1992, Chapter 14.
28. L. D. Mitchell, Gear Noise: The Purchaser's and the Manufacturer's View, Proc. of the Purdue Noise Control Conference, 1971, pp. 95-106.