Effect of tool edge wear on the cutting forces and vibrations in high-speed finish machining of Inconel 718: An experimental study and wavelet transform analysis

International Journal of Advanced Manufacturing Technology

Volumn 52, Issue 1-4, 2011, Pages 65-77

  Fang, Ning ^a   Pai, P Srinivasa ^a   Mosquea, S ^a  

^a UTAH STATE UNIVERSITY   (United States)

Author keywords

Cutting forces; Cutting vibrations; Discrete wavelet transform; High speed machining; Inconel 718; Tool edge wear

Indexed keywords

AVERAGE ENERGY; CRATER WEAR; CUTTING FORCES; CUTTING PROCESS; CUTTING VIBRATION; CUTTING VIBRATIONS; DYNAMIC TOOLS; EDGE PROFILE; EDGE WEAR; EXPERIMENTAL STUDIES; FEED FORCES; FINISH MACHINING; HIGH-SPEED; HIGH-SPEED MACHINING; HIGH-SPEED TURNING; INCONEL-718; MACHINED SURFACE QUALITY; MODERN MANUFACTURE; NICKEL- BASED SUPERALLOYS; PASSIVE FORCES; THREE COMPONENT; TOOL CUTTING EDGE; TOOL EDGE RADIUS; TOOL FAILURES; TOOL FLANK WEAR; TURNING EXPERIMENTS; VIBRATION AMPLITUDE; WAVELET COEFFICIENTS;

CUTTING; CUTTING TOOLS; DISCRETE WAVELET TRANSFORMS; FAST FOURIER TRANSFORMS; FREQUENCY BANDS; MACHINING; SPEED; THREE DIMENSIONAL; VIBRATION ANALYSIS;

EQUIPMENT;

EID: 79751534058     PISSN: 02683768     EISSN: 14333015     Source Type: Journal    
DOI: 10.1007/s00170-010-2703-6     Document Type: Article

References (38)

1. JP Davim C Maranhao MJ Jackson G Cabral J Gracio 2008 FEM analysis in high speed machining of aluminum alloy (AI7075-0) using polycrystalline diamond (PCD) and cemented carbide (K10) cutting tools Int J Adv Manuf Technol 39 1093 1100 10.1007/s00170-007-1299-y
2. VD Calatoru M Balazinski JRR Mayer H Paris G L'Esperance 2008 Diffusion wear mechanism during high-speed machining of 7475-T351 aluminum alloy with carbide end mills Wear 265 1793 1800 10.1016/j.wear.2008.04.052
3. S Zhang JF Li JX Deng YS Li 2009 Investigation on diffusion wear during high-speed machining Ti-6Al-4V alloy with straight tungsten carbide tools Int J Adv Manuf Technol 44 17 25 05812508 10.1007/s00170-008-1803-z
4. A Molinari C Musquar G Sutter 2002 Adiabatic shear banding in high speed machining of Ti-6Al-4V: experiments and modeling Int J Plast 18 443 459 0987.74504 10.1016/S0749-6419(01)00003-1 (Pubitemid 34181544)
5. J Barry G Byrne D Lennon 2001 Observations on chip formation and acoustic emission in machining Ti-6Al-4V alloy Int J Mach Tools Manuf 41 1055 1070 10.1016/S0890-6955(00)00096-1 (Pubitemid 32272842)
6. N Fang Q Wu 2009 A comparative study of the cutting forces in high speed machining of Ti-6Al-4V and Inconel 718 with a round edge tool J Mater Process Technol 209 4385 4438 10.1016/j.jmatprotec.2008.10.013
7. RS Pawade SS Joshi PK Brahmankar 2008 Effect of machining parameters and cutting edge geometry on surface integrity of high-speed turned Inconel 718 Int J Mach Tools Manuf 48 15 28 10.1016/j.ijmachtools.2007.08.004 (Pubitemid 47576563)
8. M Nalbant A Altm H Gokkaya 2007 The effect of cutting speed and cutting tool geometry on machinability properties of nickel-base Inconel 718 super alloys Mate Des 28 1334 1338 10.1016/j.matdes.2005.12.008 (Pubitemid 44817452)
9. EO Ezugwu DA Fadare J Bonney RB Da Silva WF Sales 2005 Modelling the correlation between cutting and process parameters in high-speed machining of Inconel 718 alloy using an artificial neural network Int J Mach Tools Manuf 45 1375 1385 10.1016/j.ijmachtools.2005.02.004 (Pubitemid 40821886)
10. RT Coelho LR Silva A Braghini AA Bezerra 2004 Some effects of cutting edge preparation and geometric modifications when turning INCONEL 718 (TM) at high cutting speeds J Mater Process Technol 148 147 153 10.1016/j.jmatprotec. 2004.02.001
11. D Dudzinski A Devillez 2004 A review of developments towards dry and high speed machining of Inconel 718 alloy Int J Mach Tools Manuf 44 439 456 10.1016/S0890-6955(03)00159-7
12. TI Elwardany E Mohammed MA Elbestawi 1996 Cutting temperature of ceramic tools in high speed machining of difficult-to-cut materials Int J Mach Tools Manuf 36 611 634 10.1016/0890-6955(95)00043-7 (Pubitemid 126359405)
13. N Narutaki Y Yamane 1993 High speed machining of Inconel 718 with ceramic tools CIRP Annals 42 103 106 10.1016/S0007-8506(07)62402-0 (Pubitemid 23679078)
14. Q Wu N Fang 2006 Effect of tool-edge wear in high-speed machining of superalloy Inconel 718 Trans NAMRI/SME 34 397 402
15. I Al-Zkeri J Rech T Altan H Hamdi F Valiorgue 2009 Optimization of the cutting edge geometry of coated carbide tools in dry turning of steels using a finite element analysis Mach Sci Technol 13 36 51 10.1080/10910340902776051
16. MNA Nasr E-G Ng MA Elbestawi 2007 Modeling the effects of tool-edge radius on residual stresses when orthogonal cutting AISI 316L Int J Mach Tools Manuf 47 401 411 10.1016/j.ijmachtools.2006.03.004 (Pubitemid 44738470)
17. N Fang Q Wu 2005 The effects of chamfered and honed tool edge geometry in machining of three aluminum alloys Int J Mach Tools Manuf 45 1178 1187 10.1016/j.ijmachtools.2004.12.003 (Pubitemid 40597227)
18. F Klocke H Kratz 2005 Advanced tool edge geometry for high precision hard turning CIRP Annals 54 47 50 10.1016/S0007-8506(07)60046-8 (Pubitemid 40948406)
19. YC Yen A Jain T Altan 2004 A finite element analysis of orthogonal machining using different tool edge geometries J Mater Process Technol 146 72 81 10.1016/S0924-0136(03)00846-X
20. N Fang 2003 Slip-line modeling of machining with a rounded-edge tool. Part I: new model and theory J Mech Phys Solids 51 715 742 1019.74506 10.1016/S0022-5096(02)00060-1
21. RJ Schimmel WJ Endres R Stevenson 2002 Application of an internally consistent material model to determine the effect of tool edge geometry in orthogonal machining Trans ASME J Manuf Sci Engng 124 536 543 10.1115/1.1448334 (Pubitemid 35202575)
22. BH Chen XZ Wang SH Yang C McGreavy 1999 Application of wavelets and neural networks to diagnostic system development, 1, feature extraction Comp Chem Engng 23 899 906 10.1016/S0098-1354(99)00258-6 (Pubitemid 29292592)
23. S Mallat 1989 A theory of multiresolution signal decomposition: the wavelet representation IEEE Trans Patt Analy Mach Intelli 11 674 693 0709.94650 10.1109/34.192463
24. The MathWorks (2008) MATLAB Toolbox version 7.5 users' guide. The MathWorks, Natick, MA
25. RE Haber JE Jimenez CR Peres JR Alique 2004 An investigation of tool-wear monitoring in a high-speed machining process Sens Actua A - Phys 116 539 545 10.1016/j.sna.2004.05.017
26. S Dolinsek B Sustarsic J Kopac 2001 Wear mechanisms of cutting tools in high-speed cutting processes Wear 250 349 356 10.1016/S0043-1648(01)00620-2 (Pubitemid 33053068)
27. Tang YY, Yang LH, Liu J, Ma H (2000) Wavelet theory and its application to pattern recognition, series in machine perception and artificial intelligence, vol 36. World Scientific, Singapore
28. T Li Q Li S Zhu M Ogihara 2002 A survey on wavelet applications in data mining ACM SIGKDD Explor Newslet 4 49 68 10.1145/772862.772870
29. I Daubechies 1990 The wavelet ransform, time-frequency localization and signal analysis IEEE Trans Inform Theo 36 961 1005 0738.94004 10.1109/18.57199 1066587 (Pubitemid 20738359)
30. JS Kwak 2006 Application of wavelet transform technique to detect tool failure in turning operations Int J Adv Manuf Technol 28 1078 1083 10.1007/s00170-004-2476-x
31. DE Dimla 2002 The correlation of vibration signal features to cutting tool wear in a metal turning operation Int J Adv Manuf Technol 19 705 713 10.1007/s001700200080 (Pubitemid 34726423)
32. Y Choi R Arayanaswami A Chandra 2004 Tool wear monitoring in ramp cuts in end milling using the wavelet transform Int J Adv Manuf Technol 23 419 428 10.1007/s00170-003-1898-1
33. Z Kunpeng WY San HG Soon 2009 Wavelet analysis of sensor signals for tool condition monitoring: a review and some new results Int J Mach Tools Manuf 49 537 553 10.1016/j.ijmachtools.2009.02.003
34. MR Movahhedy P Mosaddegh 2006 Prediction of chatter in high speed milling including gyroscopic effects Int J Mach Tools Manuf 46 996 1001 10.1016/j.ijmachtools.2005.07.043
35. E Solis CR Peres JE Jimenez JR Alique JC Monje 2004 A new analytical-experimental method for the identification of stability lobes in high-speed milling Int J Mach Tools Manuf 44 1591 1597 10.1016/j.ijmachtools. 2004.06.011
36. T Schmitz M Davies K Medicus J Snyder 2001 Improving high-speed machining material removal rates by rapid dynamic analysis CIRP Annals 50 263 268 10.1016/S0007-8506(07)62119-2 (Pubitemid 32610822)
37. Altintas Y (2000) Manufacturing automation: metal cutting mechanics, machine tool vibrations, and CNC design. Cambridge University Press, Cambridge
38. M Lee CE Thomas DG Wildes 1987 Prospects for in-process diagnosis of metal cutting by monitoring vibration signals J Mater Sci 22 3821 3830 10.1007/BF01133328 (Pubitemid 18546232)