Deterministic mixed lubrication modelling using roughness measurements in gear applications

Tribology International

Volumn 42, Issue 10, 2009, Pages 1406-1417

  Evans, H P ^a   Snidle, R W ^a   Sharif, K J ^a  

^a CARDIFF UNIVERSITY   (United Kingdom)

Author keywords

Contact fatigue; Contact strain energy; Mixed lubrication; Roughness

Indexed keywords

BOUNDARY LUBRICATIONS; CONTACT EVENT; CONTACT FATIGUE; CONTACT STRAIN ENERGY; ELASTOHYDRODYNAMIC CONTACT; ELASTOHYDRODYNAMIC LUBRICANT; EXTREME CONDITIONS; EXTREME PRESSURE; FILM BREAKDOWN; GEAR TOOTH SURFACE; GROUND POWER; HYDRODYNAMIC EQUATIONS; MIXED LUBRICATION; NUMERICAL SOLUTION; ROUGHNESS; SURFACE FATIGUES; TRANSMISSION GEAR; TYPICAL APPLICATION; UNIFIED NUMERICAL SOLUTION;

DENTISTRY; ELASTOHYDRODYNAMICS; FLUID DYNAMICS; GEAR TEETH; METAL ANALYSIS; STRAIN ENERGY; SURFACE PROPERTIES; SURFACE ROUGHNESS;

ELASTOHYDRODYNAMIC LUBRICATION;

EID: 68549085095     PISSN: 0301679X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.triboint.2009.05.025     Document Type: Article

References (31)

1. Patir N., and Cheng H.S. An average flow model for determining effects of three-dimensional roughness on partial hydrodynamic lubrication. Trans ASME J Lubr Technol 100 (1978) 12-17
2. Greenwood J.A., and Tripp J.J. The contact of two nominally flat rough surfaces. Proc Inst Mech Eng 187 (1971) 625-633
3. Jocsak J, Wong VW, Tian T. The effects of cylinder liner finish on piston ring-pack friction. In: Proceedings of the ASME international combustion engine division technical conference, 2004. p. 841-9.
4. Makino T., Morohoshi S., and Taniguchi S. Application of average flow model to thin film gas lubrication. Trans ASME J Tribol 115 (1993) 183-190
5. Arcoumanis C, Ostovar P, Mortier R. Mixed lubrication modelling of Newtonian and shear thinning liquids in a piston-ring configuration. In: Lubricants for passenger car and heavy duty diesel engines, SAE special publications, vol. 1304, 1997. p. 35-60.
6. Harp S.R., and Salant R.F. An average flow model of rough surface lubrication with inter asperity cavitation. Trans. ASME J Tribol 123 (2001) 134-143
7. Tripp J.H. Surface roughness effects in hydrodynamic lubrication: the flow factor method. Trans ASME J Lubr Technol 105 (1983) 458-465
8. Greenwood J.A., and Morales-Espejel G.E. The behaviour of transverse roughness in EHL contacts. Proc Inst Mech Eng, Part J, J Eng Tribol 208 (1994) 121-132
9. Venner CH, Couhier F, Lubrecht AA, Greenwood JA. Amplitude reduction of waviness in transient EHL line contacts. In: Proceedings of the 1996 Leeds-Lyon symposium on tribology, Leeds, 1996. p. 103-12.
10. Hooke C.J. Surface roughness modification in elastohydrodynamic line contacts operating in the elastic, piezoviscous regime. Proc Inst Mech Eng Part J, J Eng Tribol 212 (1998) 145-162
11. Lubrecht A.A., Graille A., Venner C.H., and Greenwood J.A. Waviness amplitude reduction in EHL line contact under rolling sliding. Trans ASME J Tribol 120 (1998) 705-709
12. Venner C.H., and Lubrecht A.A. An engineering tool for the quantitative prediction of general roughness deformation in EHL contacts based on harmonic waviness attenuation. Proc IMechE Part J, J Eng Tribol 219 (2005) 303-312
13. Hooke C.J. Engineering analysis of rough EHL contacts. Proc Inst Mech Eng Part J, J Eng Tribol 223 (2009) 517-528
14. Zhu D., and Hu Y.-Z. A computer program package for the prediction of EHL and mixed lubrication characteristics, friction, subsurface stresses and flash temperatures based on measured 3-D surface roughness. Tribol Trans 44 (2001) 383-390
15. Zhu D. On some aspects of numerical solutions of thin-film and mixed elastohydrodynamic lubrication. Proc Inst Mech Eng Part J, J Eng Tribol 221 (2007) 561-579
16. Zhu D, Ren N, Wang QJ. Pitting life prediction approach based on 3-D line contact mixed EHL analysis and subsurface von Mises stress calculation. In: Proceedings of the fifth China international symposium on tribology, Beijing, 2008.
17. Wang Q.J., Zhu D., Cheng H.S., Yu T., Jiang X., and Liu S. Mixed lubrication analyses by a macro-micro approach and a full-scale mixed EHL model. Trans ASME J Tribol 126 (2004) 81-91
18. Holmes M.J.A., Hughes T.G., Evans H.P., and Snidle R.W. Transient elastohydrodynamic point contact analysis using a new coupled differential deflection method: part 1 theory and validation; part 2 results. Proc Inst Mech Eng Part J, J Eng Tribol 217 (2003) 289-321
19. Evans H.P., and Hughes T.G. Evaluation of deflection in semi-infinite bodies by a differential method. Proc Inst Mech Eng Part C, J Mech Eng Sci 214 (2000) 563-584
20. Johnson K.L. Contact mechanics (1985), Cambridge University Press, Cambridge
21. Timoshenko S.P., and Goodier J.N. Theory of elasticity (1982), McGraw-Hill, New York
22. Qiao H., Evans H.P., and Snidle R.W. Comparison of fatigue model results for rough surface elastohydrodynamic lubrication. Proc Inst Mech Eng Part J, J Eng Tribol 222 (2008) 381-393
23. Findley W.N. A theory for the effect of mean stress on fatigue of metals under combined torsion and axial load or bending. Trans ASME J Eng Ind 81 (1959) 301-306
24. Amzallag C., Gerey J.P., Robert J.L., and Bahuaud J. Standardization of the rainflow counting method for fatigue analysis. Int J Fatigue 16 (1994) 287-293
25. Fatemi A., and Socie D.F. A critical plane approach to multiaxial fatigue damage including out-of-phase loading. Fatigue Fract Eng Mater Struct 11 (1988) 149-165
26. Patching M.J., Kweh C.C., Evans H.P., and Snidle R.W. Conditions for scuffing failure of ground and superfinished steel disks at high sliding speeds using a gas turbine engine oil. Trans ASME J Tribol 117 (1995) 482-489
27. Tao J, Hughes TG, Evans HP, Snidle RW. Elastohydrodynamic response of transverse ground gear teeth. In: Proceedings of the 28th Leeds-Lyon symposium on tribology, Amsterdam: Elsevier; 2002. p. 447-58.
28. Tao J., Hughes T.G., Evans H.P., Snidle R.W., Hopkinson N.A., Talks M., et al. Elastohydrodynamic lubrication analysis of gear tooth surfaces from micropitting tests. Trans ASME J Tribol 125 (2003) 267-274
29. Holmes M.J.A., Evans H.P., and Snidle R.W. Analysis of mixed lubrication effects in simulated gear tooth contacts. Trans ASME J Tribol 127 (2005) 61-69
30. Matake T. Explanation of fatigue limit under combined stress. Bull JSME 20 (1977) 257-264
31. Dang Van K., Cailletaud G., Flavenot J.F., Le Douaron A., and Lieurade H.P. Criterion for high cycle fatigue failure under multiaxial loading. In: Brown M.W., and Miller K.J. (Eds). Biaxial and multiaxial fatigue, EGF 3 (1989), Mechanical Engineering Publications, London 459-478