Replication technologies for HARM devices: Status and perspectives

Microsystem Technologies

Volumn 14, Issue 9-11, 2008, Pages 1599-1605

  Piotter, V ^a   Bauer, W ^a   Hanemann, T ^a,b   Heckele, M ^a   Muller C ^b  

^a KARLSRUHE INSTITUTE OF TECHNOLOGY   (Germany)

^b UNIVERSITY OF FREIBURG   (Germany)

Author keywords

[No Author keywords available]

Indexed keywords

CONCURRENT ENGINEERING; JOB ANALYSIS; MICROOPTICS; RAPID PROTOTYPING;

CYCLE TIMES; ECONOMIC EFFICIENCY; MASS-PRODUCTION; MICRO COMPONENTS; MICRO DEVICES; PROCESS STEPS; PROTOTYPING; REPLICATION PROCESSES;

PRODUCT DEVELOPMENT;

EID: 49949094386     PISSN: 09467076     EISSN: None     Source Type: Journal    
DOI: 10.1007/s00542-008-0572-9     Document Type: Conference Paper

References (17)

1. Bauer W, Knitter R (2002) J Mater Sci 37:3127-3140
2. Bauer W, Knitter R, Müller M, Ritzhaupt-Kleissl H-J (2006) Cfi/Ber. DKG 83 13:65-69
3. Bender M, Fuchs A, Plachetka U, Kurz H (2006) Status and prospects of UV-nanoimprint technology. J Microelectron Eng 83:827-830
4. Chou SY, Krauss P, Renstrom P (1995) Imprint of sub-25 nm vias and trenches in polymers. Appl Phys Lett67 (21)
5. Chou S, Krauss P, Zhang W, Guo L, Zhuang L (1997) Sub-10 nm imprint lithography and applications. J Vacuum Sci Technol 15, November/December, Nr. 6
6. Guo LJ (2007) Nanoimprint lithography: methods and material requirements. Adv Mater Nr 19:495-513
7. Elsebrock R, Makovica C, Meuffels P, Waser R (2004) Mater Lett 58:3348-3349
8. Fairley P (2003) 10 Emerging technologies that will change the World. Technology review, February
9. Hanemann T, Honnef K, Haußelt J (2007) Process chain development for the rapid prototyping of microstructured polymer, ceramic and metal parts: composite flow behaviour optimization, replication via reaction molding and thermal postprocessing. Intern J of Adv Manuf Techn 33:167-175
10. Heckele M, Schomburg WK (2004) Review on micro molding of thermoplastic polymers. J Mircomech Microeng 14:R1-R14
11. Hershey R, Miller M, Jones C, Ganapathi M, Lu X, Doyle G, Lentz D, LaBrake D (2006) PhotonicCrystal patterning for high volume LED manufacturing. proceedings of SPIE, sixth international conference on solid state lighting 6337, September
12. Knitter R, Bauer W, Göhring D, Haußelt J (2001) J Adv Eng Mater 3:49-54
13. Mehne C, Heckele M, Steger R, Warkentin D (2006) Hot embossing of large area microfluidic devices with through holes. In: 6th International Conference of the European Society for Precision Engineering and Nanotechnology (EUSPEN), Baden, A, May 28-June 1
14. Michaeli W, Opfermann D (2006) Micro assembly injection moulding. J Microsyst Technol 12:616-619
15. Pfleging W, Hanemann T, Torge M, Bernauer W (2003) Rapid fabrication and replication of metal, ceramic, and plastic mould inserts for application in microsystem technologies. J Mech Eng Sci Proc Instn Mech Engrs 217(Part C):53-63
16. Piotter V, Finnah G, Zeep B, Ruprecht R, Hausselt J (2007) Metal and ceramic micro components made by powder injection molding; materials science forum. Trans Tech Pub 534-536:373-376
17. Worgull M, Hetu J-F, Kabanemi KK, Heckele M (2006) Modeling and optimization of the hot embossing process for micro- and nanocomponent fabrication. Microsyst Technol 12(10-11):947-952