An experimental evaluation of an atomization-based cutting fluid application system for micromachining

Journal of Manufacturing Science and Engineering

Volumn 130, Issue 3, 2008, Pages 0311181-0311188

  Jun, Martin B G ^a   Joshi, Suhas S ^c,d   DeVor, Richard E ^b,c   Kapoor, Shiv G ^b,c  

^a UNIVERSITY OF VICTORIA   (Canada)

^b Department of Manufacturing ^*

^c UNIVERSITY OF ILLINOIS AT URBANA CHAMPAIGN   (United States)

^d INDIAN INSTITUTE OF TECHNOLOGY BOMBAY   (India)

Author keywords

[No Author keywords available]

Indexed keywords

ATOMIZATION; CUTTING FLUIDS; DROPS; GRINDING (MACHINING); MICROMACHINING;

ATOMIZED DROPLETS; CHIP EVACUATION; CUTTING FLUID APPLICATION; CUTTING PERFORMANCE; CUTTING TEMPERATURE; EXPERIMENTAL EVALUATION; FLUID PROPERTY; MICRO END MILLING;

CUTTING TOOLS;

EID: 49749148367     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2738961     Document Type: Article

References (22)

1. Jun, M. B. G., Liu, X., DeVor, R. E., and Kapoor, S. G., 2006, "Investigation of the Dynamics of Micro-End Milling, Part 1: Model Development," ASME J. Manuf. Sci. Eng., 128(4), pp. 893-900.
2. Shaw, M. C., Pigott, J. D., and Richardson, L. P., 1951, "Effect of Cutting Fluid Upon Chip-Tool Interface Temperature," Trans. ASME, 73(1), pp. 45-52.
3. Friedrich, C. R., 2000, "Near-Cryogenic Machining of Polymethyl Methacrylate for Micromilling Tool Development," Mater. Manuf. Processes, 15(5), pp. 667-678.
4. Yan, J., Syoji, K., and Tamaki, J., 2003, "Some Observations on the Wear of Diamond Tools in Ultra-Precision Cutting of Single-Crystal Silicon," Wear, 255(7-12), pp. 1380-1387.
5. Liu, X., Jun, M. B. G., DeVor, R. E., and Kapoor, S. G., 2004, "Cutting Mechanisms and Their Influence on Dynamic Forces, Vibrations, and Stability in Micro-Endmilling," 2001 ASME International Mechanical Engineering Congress and Exposition, Anaheim, CA, Paper No. IMECE2004-62416.
6. Han, R., Liu, J., and Sun, Y., 2005, "Research on Experimentation of Green Cutting With Water Vapor as Coolant and Lubricant," Ind. Lubr. Tribol., 57(5), pp. 187-192.
7. Pautsch, A. G., and Shedd, T. A., 2004, "Correlation of Heat Transfer Data to Film Thickness Data of the Thin Film Found in Spray Cooling," 2004 ASME International Mechanical Engineering Congress and Exposition, IMECE, Anaheim, CA, November 13-19, 2004 pp. 525-532.
8. Mathews, W. S., Lee, C. F., and Peters, J. E., 2003, "Experimental Investigations of Spray/Wall Impingement," Atomization Sprays, 13(2-3), pp. 223-242.
9. Bittorf, P. J., Kapoor, S. G., DeVor, R. E., and Rajagopalan, N., 2006, "Effect of Water Phase Surface Tension and Viscosity on Metelworking Fluid Functionality," Trans. NAMRI/SME, 34, pp. 555-562.
10. Chow, L. C., Sehmbey, M. S., and Pais, M. R., 1997, "High Heat Flux Spray Cooling," Annu. Rev. Heat Transfer, 8, pp. 291-318.
11. Lacas, F., Versaevel, P., Scouflaire, P., and Coeur-Joly, G., 1994, "Design and Performance of an Ultrasonic Atomization System for Experimental Combustion Applications," Part. Part. Syst. Charact., 11(2), pp. 166-171.
12. Heffington, S. N., and Glezer, A., 2004, "Two-Phase Thermal Management Using a Small-Scale, Heat Transfer Cell Based on Vibration-Induced Droplet Atomization," ITherm 2004 - 9th Intersociety Conference on Thermal and Thermomechanical Phenomena in Electronic Systems, June 1-4 2004, Las Vegas, NV, pp. 90-94.
13. Trujillo, M. F., Mathews, W. S., Lee, C. F., and Peters, J. E., 2000, "Modelling and Experiment of Impingement and Atomization of a Liquid Spray on a Wall," International Journal of Engine Research, 1(1), pp. 87-105.
14. Stanton, D. W., and Rutland, C. J., 1998, "Multi-Dimensional Modeling of Thin Liquid Films and Spray-Wall Interactions Resulting From Impinging Sprays," Int. J. Heat Mass Transfer, 41(20), pp. 3037-3054.
15. Stow, C. D., and Hadfield, M. G., 1980, "An Experimental Investigation of Fluid Flow Resulting From the Impact of a Water Drop with an Unyielding Dry Surface," Proc. R. Soc. London, Ser. A, 373(1755), pp. 419-441.
16. Mundo, C., Sommerfeld, M., and Tropea, C., 1995, "Droplet-Wall Collisions: Experimental Studies of the Deformation and Breakup Process," Int. J. Multiphase Flow, 21(2), pp. 151-173.
17. Cossali, G. E., Coghe, A., and Marengo, M., 1997, "Impact of a Single Drop on a Wetted Solid Surface," Exp. Fluids, 22(6), pp. 463-472.
18. Yarin, A. L., and Weiss, D. A., 1995, "Impact of Drops on Solid Surfaces: Self-Similar Capillary Waves, and Splashing as a New Type of Kinematic Discontinuity," J. Fluid Mech., 283, pp. 141-173.
19. Liu, X., DeVor, R. E., and Kapoor, S. G., 2006, "An Analytical Model for the Prediction of Minimum Chip Thickness in Micromachining," ASME J. Manuf. Sci. Eng., 128(2), pp. 474-481.
20. Autret, R., and Liang, S. Y., 2003, "Minimum Quantity Lubrication in Finish Hard Turning," Proceedings of the International Conference on Humanoid, Nanotechnology, Information Technology, Communication and Control, Environment, and Management, Manila, Philippines, March 26-28.
21. Subramani, G., Whitmore, M. C., Kapoor, S. G., and DeVor, R. E., 1990, "Temperature Distribution in a Hollow Cylindrical Workpiece During Machining. Theoretical Model and Experimental Results," Winter Annual Meeting of the American Society of Mechanical Engineers, November 25-30 1990, Dallas, TX, pp. 245-260.
22. Rice, W. B., Salmon, R., and Advani, A. G., 1966, "Effects of Cooling and Heating Workpiece and Tool on Chip Formation in Metal Cutting," Int. J. Mach. Tool Des. Res., 6(3), pp. 143-152.