Investigation of the dynamics of microend milling - Part I: Model development

Journal of Manufacturing Science and Engineering

Volumn 128, Issue 4, 2006, Pages 893-900

  Jun, Martin B G ^b   Liu, Xinyu ^b   DeVor, Richard E ^a,b   Kapoor, Shiv G ^a,b  

^a ASME

^b University of Illinois at Urbana Champaign   (United States)

Author keywords

[No Author keywords available]

Indexed keywords

CUTTING TOOLS; ELASTOPLASTICITY; GYROSCOPES; MATHEMATICAL MODELS; VIBRATIONS (MECHANICAL);

CUTTING FORCE; FAULT SYSTEM; MICROEND MILLING;

MILLING (MACHINING);

EID: 33751090443     PISSN: 10871357     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.2193546     Document Type: Article

References (23)

1. Vogler, M. P., DeVor, R. E., and Kapoor, S. G., 2004, "On the Modeling and Analysis of Machining Performance in Micro-Endmilling, Part II: Cutting Force Prediction," ASME J. Manuf. Sci. Eng., 126(4), pp. 695-705.
2. Liu, X., Jun, B. G., DeVor, R. E., and Kapoor, S. G., 2004, "Cutting Mechanisms and Their Influence on Dynamic Forces, Vibrations and Stability in Micro-Endmilling," Proceedings of IMECE, ASME.
3. Weule, H., Huntrup, V., and Trischle, H., 2001, "Micro-Cutting of Steel to Meet New Requirements in Miniaturization," CIRP Ann., 50, pp. 61-64.
4. Vogler, M. P., DeVor, R. E., and Kapoor, S. G., 2004, "On the Modeling and Analysis of Machining Performance in Micro-Endmilling, Part I: Surface Generation," ASME J. Manuf. Sci. Eng., 126(4), pp. 685-694.
5. Manjunathaiah, J., and Endres, W., 2000, "A Study of Apparent Negative Rake Angle and its Effects on Shear Angle During Orthogonal Cutting With EdgeRadiused Tools," Trans. NAMRC/SME, XXVIII, pp. 197-202.
6. Kountanya, R. K., and Endres, W. J., 2001, "A High-Magnification Experimental Study of Orthogonal Cutting With Edge-Honed Tools," in Proceedings of the ASME International Mechanical Engineering Congress and Exposition, Vol. 12, pp. 157-164.
7. Ohbuchi, Y., and Obikawa, T., 2003, "Finite Element Modeling of Chip Formation in the Domain of Negative Rake Angle Cutting," ASME J. Manuf. Sci. Eng., 125, pp. 324-322.
8. Waldorf, D. J., DeVor, R. E., and Kapoor, S. G., 1998, "A Slip-Line Field for Ploughing During Orthogonal Cutting," ASME J. Manuf. Sci. Eng., 120(4), pp. 693-699.
9. Dow, T. A., Miller, E. L., and Gerrard, K., 2004, "Tool Force and Deflection Compensation for Small Milling Tools," Precis. Eng., 28, pp. 31-45.
10. To, S., Cheung, C. F., and Lee, W. B., 2001, "Influence of Material Swelling on Surface Roughness in Diamond Turning of Single Crystal," Mater. Sci. Technol., 17, pp. 102-108.
11. Xu, M., and Marangoni, R. D., 1994, "Vibration Analysis of a Motor-Flexible Coupling-Rotor System Subject to Misalignment and Unbalance, Part I: Theoretical Model and Analysis," J. Sound Vib., 176(5), pp. 663-679.
12. Rao, A. S., and Sekhar, A. S., 1996, "Vibration Analysis of Rotor-Coupling-Bearing System With Misaligned Shafts," ASME Paper No. 96-GT-12, pp. 1-8.
13. Redmond, I., and Al-Hussain, K., 2001, "Misalignment as a Source of Vibration in Rotating Shaft Systems," in Proceedings of the International Modal Analysis Conference - IMAC, Vol. 1, pp. 116-123.
14. Al-Hussain, K. M., and Redmond, I., 2002, "Dynamic Response of Two Rotors Connected by Rigid Mechanical Coupling With Parallel Misalignment," J. Sound Vib., 249(3), pp. 483-498.
15. Kline, W. A., and DeVor, R. E., 1983, "The Effect of Runout on Cutting Geometry and Forces," Int. J. Mach. Tool Des. Res., 23, pp. 123-140.
16. Sutherland, J. W., and DeVor, R. E., 1986, "An Improved Method for Cutting Force and Surface Error Prediction in Flexible End Milling Systems," ASME J. Eng. Ind., 108(4), pp. 269-279.
17. Tai, C. C., and Fuh, K. H., 1994, "A Predictive Force Model in Ball-End Milling Including Eccentricity Effects," Int. J. Mach. Tools Manuf., 34(7), pp. 959-979.
18. Zheng, L., and Liang, S. Y., 1997, "Identification of Cutter Axis Tilt in End Milling," ASME J. Manuf. Sci. Eng., 119(3), pp. 178-185.
19. Jun, M. B. G., Kapoor, S. G., and DeVor, R. E., 2004, "Effects of End Mill Alignment Errors on Vibrations at High Spindle Speeds," Trans. NAMRC/SME, XXXII, pp. 9-16.
20. Montgomery, D., and Altintas. Y., 1991, "Mechanism of Cutting Force and Surface Generation in Dynamic Milling," ASME J. Eng. Ind., 113, pp. 160-168.
21. Johnson, K. L., 1985, Contact Mechanics. Cambridge University Press, Cambridge.
22. Fang, N., 2003, "Slip-Line Modeling of Machining With a Rounded-Edge Tool - Part I: New Model and Theory." J. Mech. Phys. Solids, 51, pp. 713-742.
23. Hughes, T. J. R., 2000, The Finite Element Method: Linear Static and Dynamic Finite Element Analysis. Dover, New York.