Piston ring tribology: A literature survey

VTT Tiedotteita - Valtion Teknillinen Tutkimuskeskus

Volumn , Issue 2178, 2002, Pages 3-105

  Andersson, Peter ^a   Tamminen, Jaana ^b   Sandström, Carl Erik ^b  

^a VTT TECHNICAL RESEARCH CENTRE OF FINLAND   (Finland)

^b AALTO UNIVERSITY   (Finland)

Author keywords

Friction; Lubrication; Piston ring; Tribology; Wear

Indexed keywords

EID: 0036970912     PISSN: 12350605     EISSN: 14550865     Source Type: Book Series    
DOI: None     Document Type: Article

References (160)

1. Affenzeller, J. and Gläser, H. Lagerung und Schmierung von Verbrennungsmotoren (Bearings and lubrication of internal combustion engines / in German). Die Verbrennungskraftmaschine, Neues Folge, Band 8. Vienna, Austria, 1996, Springer-Verlag. 397 p. ISBN 3-211-82577-0.
2. Ahn, H.-S., Kim, J.-Y. and Lim, D.-S. Tribological behaviour of plasma-sprayed zirconia coatings. Wear, 203-204(1997), pp. 77-87. (Pubitemid 127428397)
3. Akalin, O. and Newaz, G. M. A new experimental technique for friction simulation in automotive piston ring and cylinder liners. Society of Automotive Engineers, Inc., 1998, SAE Paper 981407, 6 p.
4. Akalin, O. and Newaz, G. M. Piston ring - cylinder bore friction modeling in mixed lubrication: Part II - Correlation with bench test data. Trans ASME - Journal of Tribology, 123(2001)1, pp. 219-223.
5. Akimoto, Y., Maruya, T., Sugihara, H. and Kobayashi, H. Analysis of piston top rings half-stick phenomena using optical technology. JSAE Review. 21(2000)3, pp. 396-400.
6. Amoser, M. Insights into piston-running behaviour. Wärtsilä Corporation, Marine News, (2001)2, pp. 23-27.
7. th June 2002. Stockholm, Sweden, 2002, Royal Institute of Technology KTH, Nordtrib 2002 Keynotes and Abstracts, CD-ROM, TRITA-MMK 2002:03, ISSN 1400-1179, ISRN KTH/MMK/R-02/03-SE. 10 p.
8. Arcoumanis, C., Duszynski, M., Flora, H. and Ostovar, P. Development of a piston-ring lubrication test-rig and investigation of boundary conditions for modelling lubricant film properties. Society of Automotive Engineers, Inc., 1995, SAE Paper 952468, 19 p.
9. Arcoumanis, C., Ostovar, P. and Mortier, R. Mixed lubrication modelling of Newtonian and shear thinning liquids in a piston-ring configuration. Society of Automotive Engineers, Inc., 1997, SAE Paper 972924, 26 p.
10. Ariga, S. Observation of transient oil consumption with in-cylinder variables. Society of Automotive Engineers, Inc., 1996, SAE Paper 961910, pp. 21-32.
11. Arps, J. H., Page, R. A. and Dearnaley, G. Reduction of wear in critical engine components using ion-beam-assisted deposition and ion implantation. Surface and Coatings Technology, 84(1996)1-3, pp. 579-583.
12. Ashby, M. F., Kong, H. S. and Abulawi, J. Operating manual for T-maps - a program for constructing maps for surface heating in unlubricated contacts. Cambridge, UK, 1990, Cambridge University, Engineering Department, 54 p.
13. Aue, G. K. Piston ring scuffing - general review. In: Piston ring scuffing. London, UK, 1976, Mechanical Engineering Publications Limited, pp. 1-7. ISBN 0 85298-335-2.
14. Babu, M. V., Kumar, R. K., Prabhakar, O. and Shankar, N. G. Simultaneous optimization of flame spraying process parameters for high quality molybdenum coatings using Taguchi methods. Surface and Coatings Technology, 79(1996)1-3, pp. 276-288.
15. Baranowska, J. Surface quality of grey cast irons in the context of nitriding and oxygen-sulphur nitriding. Surface and Coatings Technology, 100-101(1998), pp. 271-275. (Pubitemid 128397358)
16. Barrow, S., Werner, Th., Jaquet, D. and Terrettaz, F. Piston ring oil film thickness measurements in a two-stroke marine diesel engine as one tool to investicate piston-running behaviour. Interlaken, Switzerland, 1995, CIMAC. Proc. 21st CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, D76, p. 20.
17. Bijwe, J., Garg, A. and Gandhi, O. P. Reassessment of engine oil periodicity in commercial vechicles. Lubrication Engineering, 56(2000)1, pp. 23-29.
18. Bindumadhavan, P. N., Makesh, S., Gowrishnkar, N., Wah, H.-K. and Prabhakar, O. Aluminizing and subsequent nitriding of plain carbon low alloy steels for piston ring applications. Surface and Coatings Technology, 127(2000)2-3, pp. 251-258.
19. Bowden, F. P. and Tabor, D. The friction and lubrication of solids. Part 1. Oxford, UK, 1971 (1963), The Clarendon Press, 374 p.
20. Brauers, B. and Neuhäuser, H. J. K46 Nitrierschichten als Verschleißschutz für Kolbenringoberflächen - Werkstoffe, Erprobungsstand, Einsatzmöglichkeiten (K46 nitrided overlays as wear protection for piston ring surfaces - materials, testing and applicability / in German). Burscheid, Germany, 1989, Goetze AG, Drucksache Nr. 893810-09/98. 18 p.
21. Broszeit, E., Friedrich, C. and Berg, G. Deposition, properties and applications of PVD CrxN coatings. Surface and Coatings Technology, 11(1999)5, pp. 9-16.
22. Buchmann, M. and Gadow, R. Tribologically optimized ceramic coatings for cylinder liners in advanced combustion engines. Society of Automotive Engineers, Inc., 2001, SAE Paper 2001-01-3548, 7 p.
23. Chambers, K. W., Arneson, M. C. and Waggoner, C. A. An on-line ferromagnetic wear debris sensor for machinery condition monitoring and failure detection. Wear, 128(1988), pp. 325-337.
24. Chittenden R. J. and Priest M. Analysis of the piston assemply, bore distortion and future developments. In: Taylor, C.M. (ed.). Engine Tribology. Elsevier, 1993, Tribology series, 26, pp. 241-270. ISBN 0-444-89755-0.
25. Clarke, D. G., Sherrington, I. and Smith, E. H. Design considerations for a "floating liner" method of measuring piston/piston ring friction in internal combustion engines. In: Holmberg, K. and Nieminen, I. (eds.). Proceedings of the 5th international congress on tribology Eurotrib'89, Espoo, Finland, June 1989. Espoo, 1989, the International Tribology Council and the Finnish Society for Tribology. Vol. 2, pp. 432-438. ISBN 952-90080-1-5.
26. Clarke, D. G., Sherrington, I. and Smith, E. H. The floating liner method applied to measure instantaneous piston assembly friction in a motored engine. In: Jakobsen, J., Klarskov, M. and Eis, M. (eds.). NORDTRIB '90 Proceedings of the 4th Nordic symposium on tribology, lubrication, friction and wear. 10th-13th June 1990, Hirthals, Denmark. Copenhagen, Denmark, 1990, Technical University of Denmark. pp. 473-483. ISBN 87-983538-0-2.
27. Coy, R. C. Practical applications of lubrication models in engines. Tribology International, 31(1998)10, pp. 563-571.
28. Datoo, A. and Fox, M. F. The lubricant condition in the ring zone under cold start conditions, Synopses, the 29th Leeds-Lyon Symposium on Tribology, Tribological Research and Design for Engineering Systems, 3-6. Sept. 2002. 1 p.
29. Dearlove, J. and Cheng, W. K. Simultaneous piston ring friction and oil film thickness measurements in a reciprocating test rig. In: Recent snapshots and insights into lubricant tribology (SAE SP-1116), Warrendale, USA, 1995, SAE International, SAE Technical Paper Series 952470, pp. 29-39.
30. Demmerle, R., Barrow, S., Terrettaz, F. and Jaquet, D. New insights into the piston running behaviour of Sulzer large bore diesel engines. Frankfurt am Main, Germany, 2001, CIMAC. Proc. 23rd CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, Vol. 2, pp. 548-561.
31. De Petris, C., Giglio, V. and Police, G. Some insights on mechanisms of oil consumption. 1996. Society of Automotive Engineers, Inc., 1996, SAE Technical Paper Series 961216. 13 p.
32. DIN - German industrial standard DIN 51 777, Testing of mineraloil hydrocarbons and solvents; determination of water content according to Karl Fischer; Part 1, direct method, 4 p. +
33. Part 2, indirect method, 4 p.
34. DIN - German industrial standard DIN 51 834, part 1 and 2, Testing of lubricants - Tribological test in the translatory oscillation apparatus, 6 p. + 7 p.
35. Dong, J., Van de Voort, F. R., Ismail, A. A., Akochi-Koblé, E. and Pinchuk, D. Rapid determination of the carboxylic acid contribution to the total acid number of lubricants by Fourier transform infrared spectroscopy. Lubrication Engineering, 56(2000)6, pp. 12-20.
36. Dong, W. P., Davis, E. J., Butler, D. L. and Stout, K. J. Topographic features of cylinder liners - an application of three-dimensional characterization techniques. Tribology International, 28(1995)7, pp. 453-463.
37. Dowson, D. Piston assemblies; background and lubrication analysis. In: Taylor, C.M. (ed.). Engine Tribology. Elsevier, 1993, Tribology series, 26, pp. 213-240. ISBN 0-444-89755-0.
38. Dufrane, K. F. Wear performance of ceramics in ring/cylinder applications. Journal of the American ceramic Society, 72(1989)4, pp. 691-695.
39. Durga, V., Rao, N., Boyer, B. A., Cikanek, H. A. and Kabat, D. M. Influence of surface characteristics and oil viscosity on friction behaviour of rubbing surfaces in reciprocating engines. In: Proc. 1998 Fall Technical Conference ASME-ICE, Vol. 31-2, Paper No. 98-ICE-131, pp. 23-35.
40. Eilts, P. and Wachtmeister, G. Significance of recording and analysing the ring dynamics for the tribological optimisation of a piston ring package. London, United Kingdom, 1993, CIMAC. Proc. 20th CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, D44, p. 16.
41. Ejakov, M. A., Diaz, A. R. and Chock, H. J. Numerical optimization of ring-pack behavior. Society of Automotive Engineers, Inc., 1999, SAE Paper 1999-01-1521, 12 p.
42. Esser, J. Oil control rings and their effect on oil consumption. MTZ Worldwide, 63(2002)7-8, pp. 22-25 /
43. MTZ, 63(2002)7-8, pp. 592-601.
44. Federal-Mogul Kolbenringe Kurbelgehäuse (piston rings / crankcases). Sonderdruck aus (reprinted from) ATZ/MTZ - Supplement Shell Lexicon Verbrennungsmotor. This edition: Burcheid, Germany, 1998, Federal-Mogul Powertrain Systems, 32 p.
45. Fitch, J. C. and Troyer, D. D. Sampling methods for used oil analysis. Lubrication Engineering, 56(2000)3, pp. 40-47.
46. Fox, M. F. Ring zone lubrication: implications for reduced emissions and enhanced engine life. In: Lenthall J.S. (ed.). Collected papers from the one-day seminar The Tribology of Internal Combustion Engines, University of Birmingham, UK, 7 November 1996. London, UK, 1996, Mechanical Engineering Publications Limited, pp. 9-28. ISBN 1-86058-071-8.
47. Fox, M.F., Picken, D. J. Symons, M.C.R. and Thomson, A.L. Paramagnetic species in I/C engine top ring zone lubricant samples. Tribology International, 30(1997)6, pp. 417-422.
48. Friedrich, C., Berg, G., Broszeit, E., Rick, F. and Holland, J. PVD CrxN coatings for tribological application on piston rings. Surface and Coatings Technology, 97(1997)1-3, pp. 661-668.
49. Frølund, K. and Schramm, J. An investication of the cylinder wall oil film development during warm-up of an SI-engine using laser induced fluorerescence. Society of Automotive Engineers, Inc., 1997, SAE Technical Papers Series, 971699, pp. 75-83.
50. Galligan, J., Torrance, A. A. and Liraut, G. A scuffing test for piston ring/bore combinations Part I. Stearic acid lubrication. Wear, 236(1999a)1-2, pp. 199-209.
51. Galligan, J., Torrance, A. A. and Liraut, G. A scuffing test for piston ring/bore combinations: Part. II. Formulated motor lubrication. Wear, 236(1999b)1-2, pp. 210-220.
52. nd World Tribology Congress, Vienna, Austria, 3rd-7th September 2001. Vienna, Austria, 2001, The Austrian Tribology Society, p. 245. ISBN 3-901657-08-8.
53. Geist, M. A. and Barrow, S. Integrating Past, Present and Future: How Owners and operators can benefit from the latest developments even in older RTA-Engines. Hamburg, Germany, 2001, CIMAC. Proc. 23rd CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, Vol. 3, pp. 897-912.
54. Glaeser, W. A. Materials for tribology. Amsterdam, The Netherlands, 1992, Elsevier Science Publishers B.V., Tribology Series 20, 260 p. ISBN 0-444-88495-5.
55. Glaeser, W. A. and Gaydos, P. A. Development of a wear test for adiabatic diesel ring and liner materials. ASTM 1993, Proc Symp wear test selection for design and application, Dec 2 1992. Miami, FL, USA, ASTM Philadelphia PA, 0066-0558 ASTTA8, ASBN 0-8031-1856-2, pp. 1-16.
56. Glidewell, J. and Korcek, S. Piston ring / cylinder bore friction under flooded and starved lubrication using fresh and aged engine oils. Society of Automotive Engineers, Inc., 1998, SAE Paper 982659, 10 p.
57. Godfrey, D. recognition and solution of some common wear problems related to lubricants and hydraulic fluids. Lubrication engineering, 56(2000)8, pp. 33-36.
58. Golloch, R., Kessen, U. and Merker, G. P. Tribological investigations on the piston assembly group of a diesel engine. MTZ Worldwide, 63(2002)6, pp. 21-24 /
59. MTZ, 63(2002)6, pp. 494-500.
60. th June 1990, Hirthals, Denmark. Copenhagen, Denmark, 1990, Technical University of Denmark. pp. 349-361. ISBN 87-983538-0-2.
61. Gulwadi, S. D., Analysis of tribological performance of a piston ring pack. Tribology Transactions, 43(2000)2, pp. 151-162.
62. Gupta, P. On a multi-process wear model. Lubrication Engineering, 57(2001)4, pp. 19-24.
63. Haddad. S. D. and Tjan, K.-T. An analytical study of offset piston and crankshaft designs and the effect of oil film on piston slap excitation in a diesel engine. Mechanism and Machine Theory, 30(1995)2, pp. 271-284.
64. Hamatake, T., Wakuri, Y., Soejima, M. and Kitahara T. Some studies on the tribology of diesel engines. Hamburg, Germany, 2001, CIMAC. Proc. 23rd CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, Vol. 4, pp. 1426-1440.
65. Han, D.-C. and Lee, J.-S. Analysis of the piston ring lubrication with a new boundary codition. Tribology International, 31(1998)12, pp. 753-760.
66. Harigaya, Y., Akagi, J. and Suzuki, M. Prediction of temperature, viscosity and thickness in oil film between ring and liner of an internal combustion engine. Society of Automotive Engineers, Inc., 2000, SAE Technical Paper Series 2000-01-1790, 9 p.
67. Harrison, K. Get your jacket - can improved performance be achieved with plasma-aprayed coatings? Engine Technology International, (2002)2, pp. 54-56.
68. Haselkorn, M. H. and Kelley, F. A. Development of wear resistant ceramic coatings for diesel engines, SAE Proceedings of the Annual Automotive Technology Development Contractors Co-ordination Meeting, 1992, pp. 417-424.
69. Henein, N. A., Ma, Z., Huang, S., Bryzik, W. and Glidewell, J. In situ wear measuring technique in engine cylinders. STLE Tribology Transactions, 41(1998)4, pp. 579-585.
70. Heywood, J. B. Internal Combustion Engine Fundamentals. McGraw-Hill. Singapore. 1988. 930 p. ISBN 0-07-100499-8.
71. Holmberg, K. and Matthews, A. Coatings tribology. Amsterdam, The Netherlands, 1994, Elsevier Science B.V., Dowson, D. (ed.), Tribology Series, 28, 442 p. ISBN 0 444 88870 5.
72. Hu, Y. Z., Li, N. and Tønder, K. A dynamic system model for lubricated sliding wear and running-in. Transactions of the ASME, Journal of Tribology, 113(1991), pp. 499-505. (Pubitemid 21680112)
73. Hu, Y., Cheng, H. S., Arai, T., Kobayashi, Y. and Aoyama, S. Numerical simulation of piston ring in mixed lubrication - A non-axi-symmetrical analysis, ASME Journal of Tribology, 116(1994), pp. 470-478. (Pubitemid 283131)
74. Hunt, T. M. Handbook of wear debris analysis and particle detection in liquids. London, 1993. Elsevier Science Publishers Ltd. 488 p. ISBN 1-85166-962-0.
75. Inada, Y. A new design of nodular cast iron piston for high BMEP diesel engines. Hamburg, Germany, 2001, CIMAC. Proc. 23rd CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, Vol. 2, pp. 536-547.
76. ISO - International Standard 6621-1, Internal combustion engines - Piston rings - Part 1: Vocabulary, 1986.
77. ISO - International Standard 6621-4, Internal combustion engines - Piston rings - Part 4: General specifications, 1988.
78. Jefferies, A. and Ameye, J. RULER™ and used engine oil analysis programs. Lubrication Engineering, 54(1998)5, pp. 29-34.
79. Jiang, Q. Y. and Wang, S. N. Abrasive wear of locomotive diesel engines and contaminant control. Tribology Transactions, 41(1998)4, pp. 605-609.
80. Jones, G. W. and Eleftherakis, J. G. Correlating engine wear with filter multipass testing. Society of Automotive Engineers, Inc., 1995, SAE Technical Papers Series, 952555, 19 p.
81. Josef, O. and Merker, G. P. Development of a measuring technique for cylinder bore distortion during fired engine operation. Proceedings of the 22th CIMAC International Congress on Combustion Engines, Copenhagen, May 18-21, 1998, Vol. 5, pp. 1307-1313.
82. nd CIMAC International Congress on Combustion Engines, Copenhagen, 18-21.5.1998, Vol. 3, pp. 587-592.
83. Kauzlarich, J. J. and Williams, J. A. Archard wear and component geometry. Proceedings of the Institution of Mechanical Engineers Part J, Journal of Engineering Tribology, 215(2001)4, pp. 387-403.
84. Kong, H.S. and Ashby, M.F. Friction-heating maps and their applications. MRS Bulletin, 16(1991)10, pp. 41-48.
85. Korcek, S., Jensen, R. K., Johnson, M. D. and Sorab, J. Maximising the fuel efficiency of engine oils: the role of tribology. Tribotest, 7(2001)3, pp. 187-201.
86. Kumar, R., Kumar, S., Prakash, B. and Sethuramiah, A. Assessment of engine liner wear from bearing area curves. Wear, 239(2000)2, pp. 282-286.
87. Kustas, F. M. and Buchholtz, B. W. Lubricious-surface-silicon-nitride rings for high-temperature tribological applications. Tribology transactions, 39(1996)1, pp. 43-50.
88. Lacey, P. I., Stockwell, R. T., Development of a methology to predict cylinder liner scuffing in the 6V92TA engine lubricant test. Tribology Transactions, 42(1999)1, pp. 192-201.
89. Lenhof, U. and Zwein, F. Engine cylinder metrology. MTZ worldwide, 63(2002)5, pp. 6-9 /
90. MTZ, 63(2002)5, pp. 360-369.
91. Lenthall, J. S. Cylinder bore surface finish - its evolution and specification. In: Lenthall J.S. (ed.). Collected papers from the one-day seminar The Tribology of Internal Combustion Engines, University of Birmingham, UK, 7 November 1996. London, UK, 1996, Mechanical Engineering Publications Limited, pp. 29-37. ISBN 1-86058-071-8.
92. Lipp, S. and Schmidt, R. The new FERROCOMP®-piston for high cylinder output. Hamburg, Germany, 2001, CIMAC. Proc. 23rd CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, Vol. 2, pp. 527-535.
93. Liu, Y. and Reitz, R. D. Modeling of heat conduction within chamber walls for multidimensional internal combustion engine simulations. International Journal of Heat Mass Transfer, 41(1998), pp. 839-869.
94. Loenne, K. The effects of the engine operating conditions on cylinder distortions. Muskegon Engineering Data, Goetze paper D7, 1972.
95. Loenne, K. and Ziemba, R. The Goetze cylinder distortion measurement system and the possibilities of reducing cylinder distortions. Society of Automotive Engineers, Inc., 1988, SAE paper 880142, pp. 25-33.
96. Ma, M. T., Sherrington, I., Smith, E.H. and Grice. N. Development of a comprehensive model for piston-ring lubrication in IC engines with circular and non-circular cylinder bores. In: Preprints from the 7th Nordic symposium on Tribology NORDTRIB '96, 16th-19th June 1996, Bergen, Norway. Vol. 1, 20 p.
97. Ma, M-T., Sherrington, I., Smith, E.H. and Grice, N. Development of a detailed model for piston-ring lubrication in IC engines with circular and non-circular cylinder Bores. Tribology International, 30(1997a)11, pp. 779-788.
98. Ma, M. T., Smith, E. H. and Sherrington. I. Analysis of lubrication and friction for a complete piston-ring pack with an improved oil availability model - Part 2: circumferentially variable film. Proceedings of the Institution of Mechanical Engineers Part J, Journal of Engineering Tribology, 211(1997b)1, pp. 17-27.
99. Ma, Z., Henein, N. A., Bryzik, W. and Glidewell, J. Break-in liner wear and piston ring assembly friction in a spark ignited engine. STLE Tribology Transactions, 41(1998)4, pp. 497-504.
100. Maass, H. Gestaltung und Hauptmessungen der Verbrennungskraftmaschine (Design and main dimensions of internal combustion engines / in German). Die Verbrennungskraftmaschine Neue Folge Band 1, Springer-Verlag, Vienna, Austria, 1979, 313 p. ISBN 3-211-81562-7
101. Maass, H. and Klier, H. Kräfte, Momente und deren Ausgleich in der Verbrennungskraftmaschine (Forces, moments and their equilisation in internal combustion engines / in German). Die Verbrennungskraftmaschine, Neue Folge, Band 2. Vienna, Austria, 1981, Springer-Verlag, 422 p. ISBN 3-211-81677-1.
102. Macián, V., Tormos, B. and Lerma, M. J. Evaluation of metallic elements in oil for an engine fault-diagnosis system. Tribotest, 8(2001)2, pp. 163-176.
103. Matthews, C. Engineers' data book; Second edition. London, UK, 2000. Professional Engineering Publishing Limited. 238 p. ISBN 1 86058 248 6.
104. Mattsson, C. Measurement of the oil film thickness between the cylinder liner and the piston rings in a heavy duty directly injected diesel engine. Society of Automotive Engineers, Inc., 1995, SAE Technical Paper Series 952469. 8 p.
105. McClelland, J. F. and Jones, R. W. FTIR photoacoustic spectroscopy of diesel lubricating oils containing particulate matter. Lubrication Engineering, 57(2001)9, pp. 17-21.
106. Michail, S. K. and Barber, G. C. The effects of roughness on piston ring lubrication: part 2 - the relationship between cylinder wall surface topography and oil film thickness. Tribology Transactions, 38(1995), pp. 173-177.
107. Miyake, S., Tanaka, T., Goto, T. and Knudsen, T.S. Development of spray-coated cylinder liner for diesel engine. Hamburg, Germany, 2001, CIMAC. Proc. 23rd CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, Vol. 3, pp. 913-920.
108. Mollenhauer, K. (Ed.). Handbuch Dieselmotoren (Diesel engines / in German). Berlin, Germany, 1997, Springer-Verlag, 1023 p. ISBN 3-540-62514-3.
109. Moore, S. The complexities of piston ring lubrication in a large two-stroke marine diesel engine. Proceedings 22nd CIMAC International Congress on Combustion Engines, Copenhagen, 18-21.5.1998, Vol. 3, pp. 575-586.
110. Moore, S. The measurement of piston ring oil film thickness in a two-stroke marine diesel engine. London, United Kingdom, 1993, CIMAC. Proc. 20th CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, D04, p. 13.
111. Moore, S. The influence of engine operating parameters on piston ring oil film thickness in a marine diesel engine. Interlaken, Switzerland, 1995, CIMAC. Proc. 21st CIMAC world congress on combustion engine technology for ship propulsion, power generation, rail traction, D56, p. 12.
112. Moritani, H. and Nozawa, Y. Investigation on oil degradation in piston second-land region of gasoline engine. Japanese Journal of Tribology, 44(1999)4, pp. 435-446.
113. Munro, R. Diesel engine ring scuff - is there a major problem? In: Piston ring scuffing. London, UK, 1976, Mechanical Engineering Publications Limited, pp. 9-14. ISBN 0 85298-335-2.
114. Nakayama, T., Seki, M., Someya, T. T. and Furuhama, S. Effect of oil ring geometry on oil film thickness in the circumferential direction of the cylinder. 1998. SAE Technical Paper Series 982578. 7 p.
115. Newby, K. R. Functional chromium plating. Metal Finishing, 98(2000)1, pp. 223-224.
116. Noorman, M. T., Assanis, D. N., Patterson, D. J., Tung, S. C. and Tseregounis, S. I. Overview of techniques for measuring friction using bench tests and fired engines. In: Advances in powertrain tribology 2000, SAE/SP-00/1548, SAE Inc., Warrendale, PA, USA, 2000, ISBN 0-7680-0617-1, Paper 2000-01-1780, pp. 1-11.
117. Ohlsson, R. A topographic study of functional surfaces. Göteborg, Sweden, 1996, Chalmers University of Technology, Department of Production Engineering, Doctors Thesis, PTA 96:05, ISBN 91-7197-351-6, ISSN 1100-7524, 43 p. + Appx. 76 p.
118. Patterson, D. J., Hill, S. H. and Tung, S. C. Bench wear testing of engine power cylinder components. Journ STLE Lubrication Engineering, 49(1993)2, pp. 89-95.
119. Pawlus, P. Change of cylinder surface topography in the initial stage of engine life. Wear, 209(1997)1-2, pp. 69-83.
120. Perrin, K., Pandosh, J., Searle, A., Shaub, H. and Sprague, S. Radioactive tracer study of start-up wear versus steady-state wear in a 2.3 liter engine. In: Rcent snapshots and insights into lubricant tribology (SAE SP-1116). Warrendale, USA, 1995, SAE International, SAE Technical Paper Series 952474, pp. 85-98.
121. Priest, M. and Taylor, C. M. Automobile engine tribology - approaching the surface. Wear, 241(2000)2, pp. 193-203.
122. Priest, M., Dowson, D. and Taylor, C. M. Predictive wear modelling of lubricated piston rings in a diesel engine. Wear, 231(1999)1, pp. 89-101.
123. Qiu, X., Hamdi, A., Elmoursi, A. and Malaczynski, G. Development of bench test methods for the evaluation of ion-implanted materials: Piston/bore application. Surface and Coatings Technology, 88(1996)1-3, pp. 190-196.
124. Radil, K. The influence of honing on the wear of ceramic coated piston rings and cylinder liners. Lubrication Engineering, 57(2001)7, pp. 10-14.
125. Rastegar, F. and Richardson, D. E. Alternative to chrome: HVOF cermet coatings for high horse power diesel engines. Surface and Coatings Technology, 90(1997)1-2, pp. 156-163.
126. Reipert, P. and Voigt, M. Simulation of the Piston/Cylinder Behavior for Diesel Engines. Society of Automotive Engineers, Inc., 2001, SAE Technical Paper Series 2001-01-0563. 18 p.
127. Richardson, D. E. Comparison of measured and theoretical inter-ring gas pressure on a diesel engine. Society of Automotive Engineers, Inc., 1996, SAE Technical Papers Series 961909. Pp. 7-20.
128. Richardson, D. E. and Borman, G. L. Theoretical and experimental investigation of oil films for application to piston ring lubrication. Society of Automotive Engineers, Inc., 1992, SAE Paper 922341, 16 p. (SAE 922341 from SAE SP-936)
129. nd World Tribology Congress, Vienna, Austria, 3rd-7th September 2001. Vienna, Austria, 2001, The Austrian Tribology Society, CD-ROM, 4 p. ISBN 3-901657-09-6.
130. Ronkainen, H. Tribological properties of hydrogenated and hydrogen-free diamond-like coatings. Espoo, Finland, 2001, VTT Technical Research Centre of Finland, VTT Publications 434, 52 p. + app. 91 p. ISBN 951-38-5848-0.
131. Röhrle, M. D. Pistons for internal combustion engines - fundamentals of piston technology, MAHLE GmbH. Verlag Moderne Industrie. Landsberg/Lech, Germany. 1995. p. 70.
132. th September 1990. Amsterdam, The Netherlands, 1991, Elsevier Science Publishers B.V., Tribology Series, 18, pp. 103-109. ISBN 0-444-88796-2.
133. Saini, M. S., Lockwood, F. E., Smith, T. R., Pridemore, D. and Grulke, E. A. Statistical study of organomolybdenum compounds in an engine oil formulation and the results of engine testing. Tribotest, 8(2001)1, pp. 27-44.
134. Seki, T., Nakayama, K., Yamada, T., Yoshida, A. and Takiguchi, M. A study on variation in oil film thickness of a piston ring package: variation of oil film thickness in piston sliding direction. JSAE Review, 21(2000), 3, pp. 315-320.
135. Shenghua, L., Jijun, L., Lonbao, Z. and Rong, W. An Experimental Investigation of the Oil Film Lubricating Piston Rings. Society of Automotive Engineers, Inc., 1996. SAE Technical Paper Series 961912. 5 p.
136. Sherrington, I. and Mercer, S. The use of topography-based parameters for the assessment and prediction of surface wear. Tribotest, 7(2000)1, pp. 3-11.
137. Shuster, M., Mahler, F. and Crysler, D. Metallurgical and metrological examinations of the cylinder liner - piston ring surfaces after heavy duty diesel engine testing. STLE Tribology Transactions, 42(1999)1, pp. 116-125.
138. Shuster, M., Combs, D., Karrip, K. and Burke, D. Piston ring cylinder liner scuffing phenomenon studies using acoustic emission technique. Society of Automotive Engineers, Inc., 2000, SAE Paper 2000-01-1782, 13 p.
139. Steinhoff, K., Schelle, C. and Kopp, R. Steuerung von Schmierungsprozessen durch modifikation de Oberflächenenergie (Lubrication process control by surface energy modification / in German). Tribologie + Schmierungstechnik, 48(2001)5, pp. 21-26.
140. Sui, P. C. and Ariga, S. Piston ring pack friction and lubrication analysis of an automobile engine using a mixed lubrication model. Society of Automotive Engineers, Inc., 1993, SAE Paper 931937, 15 p.
141. Takiguchi, M., Ando, H., Takimoto, T. and Uratsuka, A. Characteristics of friction and lubrication of two-ring piston. JSAE Review, 17(1996)1, pp. 11-16.
142. Takiguchi, M., Nakayama, K., Furuhama, S. and Yoshida, H. Variation of piston ring oil film thickness in an internal combustion engine. Society of Automotive Engineers, Inc., 1998, SAE Technical Paper Series 980563, 9 p.
143. Takiguchi, M., Sasaki, R., Takahashi, I., Ishibashi, F., Furuhama, S., Kai, R. and Sato, M. Oil film thickness measurement and analysis of a three ring pack in an operating diesel engine. Society of Automotive Engineers, Inc., 2000, SAE Technical Paper Series 2000-01-1787, 10 p.
144. Taylor, C. M. Automobile engine tribology - design considerations for efficiency and durability. Wear, 221(1998)1, pp. 1-8.
145. Taylor, R. I. Engine friction: the influence of lubricant rheology. Proceedings of the Institution of Mechanical Engineers Part J, Journal of Engineering Tribology, 211(1997)3, pp. 235-246.
146. Terheci, M., Manory, R. R. and Hensler, J. H. The friction and wear of automotive grey cast iron under dry sliding conditions. Part 1: Relationships between wear loss and testing parameters. Wear, 180(1995)1-2, pp. 73-78.
147. Thirouard, B., Tian, T. and Hart, D. P. Investigation of oil transportation mechanisms in the piston ring pack of a single cylinder diesel engine, using two dimensional laser induced fluorescence. Society of Automotive Engineers, Inc., 1998, SAE Technical Paper Series 982658. 9 p.
148. Tian, T. Dynamic behaviours of piston rings and their practical impact. Part 2: Oil transport, friction and wear of ring/liner interface and effects of piston and dynamics. Proc Instn Mech Engrs Vol 216 Part J, Engineering Tribology, 2002, pp. 229-247.
149. Tian, T., Wong, V. W. and Heywood, J. B. A piston ring-pack film thickness and friction model for multigrade oils and rough surfaces. Society of Automotive Engineers, Inc., 1996, SAE Technical Paper Series 962032, 12 p.
150. Tian, T., Wong, V. W. and Heywood, J. B. Modeling the dynamics and lubrication of three piece oil control rings in internal combustion engines. Society of Automotive Engineers, Inc., 1998, SAE Paper 982657, 17 p.
151. Truhan, J. J., Covington, C. B. and Wood, L. The classification of lubricating oil contaminants and their effect on wear of diesel engines as measured by surface layer activation. Society of Automotive Engineers, Inc., 1995, SAE Technical Paper Series, 952558, 10 p.
152. Tung, S. C. and Tseregounis, S. I. An investigation of tribological characteristics of energy-conserving engine oils using a reciprocating bench test. In: Advances in powertrain tribology 2000, SAE/SP-00/1548, SAE Inc., Warrendale, PA, USA, 2000, ISBN 0-7680-0617-1, Paper 2000-01-1781, pp. 13-21.
153. Urabe, M., Tomomatsu, T., Ishiki, K., Takiguchi, M. and Someya, T. Variation of Piston Friction Force and Ring Lubricating Condition in a Diesel Engine with EGR. Society of Automotive Engineers, Inc., 1998. SAE Technical Paper Series 982660. 6 p
154. Vetter J. and Nevoigt, A. a-C:HMe coatings deposited by the cathodic vacuum arc deposition: properties and application potential. Surface and Coatings Technology, 120-121 (1999), pp. 709-717.
155. Wakuri, Y., Soejima, M., Ejima, Y., Hamatake, T. and Kitahara, T. Studies on friction characteristics of reciprocating engines. Society of Automotive Engineers, Inc., 1995, SAE Technical Paper Series 952471, 15 p.
156. Wang, Y. and Tung, S.C. Scuffing and wear behavior of aluminum piston skirt coatings against aluminum cylinder bore. Wear, 225-229(1999)2, pp. 1100-1108.
157. Willcock, M. Recent developments in piston assemblies. In: Lenthall J.S. (ed.). Collected papers from the one-day seminar The Tribology of Internal Combustion Engines, University of Birmingham, UK, 7 November 1996. London, UK, 1996, Mechanical Engineering Publications Limited, pp. 9-28. ISBN 1-86058-071-8.
158. Willn, J. E. and Brett, P. S. An investigation into piston ring scuffing during running-in. In: Piston ring scuffing. London, 1976, Mechanical Engineering Publications Limited, ISBN 0 85298-335-2. pp. 71-78.
159. nd World Tribology Congress, Vienna, Austria, 3-7 September 2001. Vienna, Austria, 2001, The Austrian Tribology Society, CD-ROM, 4 p. ISBN 3-901657-09-6.
160. Zhuo, S., Peijun, Z., Leheng, Z., Xinfu, X., Aimin, H. and Wenquan, Z. Multi-layer compound coating on cast iron piston ring by multi-arc and magnetron sputtering ion compound plating technique. Surface and Coatings Technology, 131(2000)1-3, pp. 422-427.