Influence of surface anomalies following hole making operations on the fatigue performance for a nickel-based superalloy

Journal of Manufacturing Science and Engineering

Volumn 136, Issue 5, 2014, Pages

  Herbert, C ^a   Axinte, D A ^a   Hardy, M ^b   Withers, P ^c  

^a UNIVERSITY OF NOTTINGHAM   (United Kingdom)

^b ROLLS ROYCE PLC   (United Kingdom)

^c UNIVERSITY OF MANCHESTER   (United Kingdom)

Author keywords

[No Author keywords available]

Indexed keywords

AIRCRAFT ENGINES; EFFICIENCY; ELECTRONICS PACKAGING; ENGINES; FATIGUE TESTING; FRACTURE TESTING; MICROSTRUCTURE; NICKEL ALLOYS; SHOT PEENING; SUPERALLOYS; THERMAL FATIGUE;

AERO ENGINE MANUFACTURERS; AERO-ENGINE APPLICATIONS; COMPONENT PERFORMANCE; DAMAGE-FREE SURFACES; ELEVATED TEMPERATURE; FATIGUE-CRACK NUCLEATION; MATERIAL MICROSTRUCTURES; NICKEL- BASED SUPERALLOYS;

CRACKS;

EID: 84905914331     PISSN: 10871357     EISSN: 15288935     Source Type: Journal    
DOI: 10.1115/1.4027619     Document Type: Article

References (27)

1. Reed, R., 2006, The Superalloys Fundamentals and Applications, Cambridge University Press, New York.
2. Turan, D., Hunt, D., and Knowles, D. M., "Dwell Time Effect on Fatigue Crack Growth of RR1000 Superalloy," Mater. Sci. Technol., 23(2), pp. 183-188.
3. Novovic, D., Dewes, R. C., Aspinwall, D. K., Voice, W. E., and Bowen, P., 2004, "The Effect of Machined Topography and Integrity on Fatigue Life," Int. J. Mach. Tools Manuf., 44(2-3), pp. 125-134
4. Axinte, D. A., Andrews, P., Li, W., Gindy, N., and Withers, P. J., 2006, "Turning of Advanced Ni Based Alloys Obtained via Powder Metallurgy Route," Ann. CIRP, 55(1), pp. 117-120. (Pubitemid 44578375)
5. Mantle, A., 2001, "Surface Integrity of a High Speed Milled Gamma Titanium Aluminide," J. Mater. Process. Technol., 118(1-3), pp. 143-150. (Pubitemid 33147977)
6. Kwong, J., Axinte, D. A., and Withers, P. J., 2009, "The Sensitivity of Ni-Based Superalloy to Hole Making Operations: Influence of Process Parameters on Subsurface Damage and Residual Stress," J. Mater. Process. Technol., 209(8), pp. 3968-3977.
7. Kwong, J., Axinte, D. A., Withers, P. J., and Hardy, M. C., 2009, "Minor Cutting Edge-Workpiece Interactions in Drilling of an Advanced Nickel-Based Superalloy," Int. J. Mach. Tools Manuf., 49(7-8), pp. 645-658.
8. Ulutan, D., and Ozel, T., 2011, "Machining Induced Surface Integrity in Titanium and Nickel Alloys: A Review," Int. J. Mach. Tools Manuf., 51(3), pp. 250-280.
9. Kitagawa, T., 1997, "Temperature and Wear of Cutting Tools in High-Speed Machining of Inconel 718 and Ti-6Al-6V-2Sn," Wear, 202(2), pp. 142-148.
10. Mitchell, R. J., Hardy, M. C., Preuss, M., and Tin, S., 2004, Development of Y Prime Morphology in P/M Rotor Disc Alloys During Heat Treatment, Superalloys: The Minerals, Metals & Materials Society, Champion, PA, pp. 361-370.
11. Mitchell, R. J., Preuss, M., Tin, S., and Hardy, M. C., 2008, "The Influence of Cooling Rate From Temperatures Above the c0 Solvus on Morphology, Mismatch and Hardness in Advanced Polycrystalline Nickel-Base Superalloys," Mater. Sci. Eng., A, 473, pp. 158-165.
12. Ekmekci, B., 2007, "Residual Stresses and White Layer in Electric Discharge Machining (EDM)," Appl. Surf. Sci., 253(23), pp. 9234-9240. (Pubitemid 47320841)
13. Smith, S., Melkote, S. N., Lara-Curzio, E., Watkins, T. R., Allard, L., and Riester, L., 2007, "Effect of Surface Integrity of Hard Turned AISI 52100 Steel on Fatigue Performance," Mater. Sci. Eng., A, 459(1-2), pp. 337-346. (Pubitemid 46586118)
14. Herbert, C. R. J., Axinte, D., Hardy, M. C., and Brown, P. D., 2012, "Investigation into the Characteristics of White Layers Produced in a Nickel-Based Superalloy From Drilling Operations," Mach. Sci. Technol.: Int. J., 16(1), pp. 40-52.
15. Osterle, W., Li, P. X., and Nolze, G., "Influence of Surface Finishing on Residual Stress Depth Profiles of a Coarse-Grained Nickel-Base Superalloy," Mater. Sci. Eng., A, 262(1-2), pp. 308-311.
16. Ramesh, A., Melkote, S. N., Allard, L. F., Riester, L., and Watkins, T. R., 2005, "Analysis of White Layers Formed in Hard Turning of AISI 52100 Steel," Mater. Sci. Eng., A, 390(1-2), pp. 88-97. (Pubitemid 40014587)
17. Axinte, D. A., and Andrews, P., 2007, "Some Considerations on Tool Wear andWorkpiece Surface Quality of Holes Finished by Reaming or Milling in a Nickel-Base Superalloy," Proc. Inst.Mech. Eng., Part B, 221, pp. 591-603. (Pubitemid 46897851)
18. Harrison, I. S., Kurfess, T. R., Oles, E. J., and Singh, P. M., 2007, "Inspection of White Layer in Hard Turned Components Using Electrochemical Method," ASME J. Manuf. Sci. Eng., 129(2), pp. 447-452. (Pubitemid 46869425)
19. Griffiths, B. J., 1987, "Mechanisms of White Layer Generation With Reference to Machining and Deformation Processes," ASME J. Tribol., 109(3), pp. 525-530 (Pubitemid 17615967)
20. Boothroyd, G., 1975, Fundamentals of Metal Machining and Machine Tools, Marcel Dekker, New York.
21. Alexandre, F., 2004, "Modeling the Optimum Grain Size on the Low Cycle Fatigue Life of a Ni Based Superalloy in the Presence of Two Possible Crack Initiation Sites," Scr. Mater., 50(1), pp. 25-30.
22. Li, W., Withers, P. J., Axinte, D., Preuss, M., and Andrews, P., 2009, "Residual Stresses in Face Finish Turning of High Strength Nickel-Based Superalloy," J. Mater. Process. Technol., 209, pp. 4896-4902.
23. Li, W., 2008, "Machining-Induced Residual Stress on a High Strength Nickel-Base Powder Superalloy," Ph.D. thesis, University of Manchester, Manchester, UK.
24. Wusatowska-Sarnek, A. M., Dubiel, B., Czyrska-Filemonowicz, A., Bhowal, P. R., Ben Salah, N., and Klemberg-Sapieha, J. E., 2011, "Microstructural Characterization of the White Etching Layer in Nickel-Based Superalloy," Metall. Mater. Trans. A, 42, pp. 3813-3825.
25. Forest, A. V., 1936, "The Rate of Growth of Fatigue Cracks," ASME J. Appl. Mech., 3, pp. 23-25.
26. Withers, P. J., 2007, "Residual Stress and Its Role in Failure," Rep. Prog. Phys., 70, pp. 2211-2264.
27. Gray, H., Wagner, L., and Lutjering, G., 1987, "Influence of Shot Peening Induced Surface Roughness, Residual Macrostress and Dislocation Density on the Elevated Temperature HCF-Properties of Ti Alloy," Third International Conference on Shot Peening, pp. 447-457.