Residual stresses in face finish turning of high strength nickel-based superalloy

Journal of Materials Processing Technology

Volumn 209, Issue 10, 2009, Pages 4896-4902

  Li, W ^a   Withers, P J ^a   Axinte, D ^b   Preuss, M ^a   Andrews, P ^c  

^a UNIVERSITY OF MANCHESTER   (United Kingdom)

^b UNIVERSITY OF NOTTINGHAM   (United Kingdom)

^c ROLLS ROYCE PLC   (United Kingdom)

Author keywords

Plastic work; Superalloy; Tooling condition; Turning; X ray diffraction

Indexed keywords

CUTTING CONDITIONS; DEPTH PROFILES; HIGH STRENGTHS; LAYER REMOVALS; MACHINING TRIALS; NICKEL- BASED SUPERALLOYS; PEAK WIDTHS; PLASTIC WORK; RADIAL DIRECTIONS; STRESSED ZONES; STRESSES DISTRIBUTIONS; SURFACE FINISHES; TOOL BREAKAGES; TOOL COATINGS; TOOL WEARS; TOOLING CONDITION;

DIFFRACTION; NICKEL ALLOYS; PLASTIC COATINGS; RESIDUAL STRESSES; SUPERALLOYS; TURNING; X RAY DIFFRACTION; X RAY DIFFRACTION ANALYSIS;

STRENGTH OF MATERIALS;

EID: 67349239975     PISSN: 09240136     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.jmatprotec.2009.01.012     Document Type: Article

References (16)

1. Arunachalam R.M., Mannan M.A., and Spowage A.C. Surface integrity when machining age hardened Inconel 718 with coated carbide cutting tools. International Journal of Machine Tools & Manufacture 44 (2004) 1481-1491
2. Axinte D.A., Andrews P., Li W., Gindy N., and Withers P.J. Turning of advanced Ni based alloys obtained via powder metallurgy route. Proceedings of CIRP 56. Kobe (2006)
3. Cullity B.D., and Stock S.R. Elements of X-ray Diffraction (2001), Prentice-Hall, Inc., New York
4. El-Wardany T.I., Kishawy H.A., and Elbestawi M.A. Surface integrity of die material in high speed machining. Part 2. Microhardness variations and residual stress. Journal of Manufacturing Science & Engineering 122 (2000) 632-641
5. Henriksen E.K. Residual stresses in machined surfaces. Journal of Applied Mechanics 73 (1951) 69-76
6. Hua J., Shivpuri R., Cheng X., Bedekar V., Matsumoto Y., Hashimoto F., and Watkins T.R. Effect of feed rate, workpiece hardness and cutting edge on subsurface residual stress in the hard turning of bearing steel using chamfer+hone cutting edge geometry. Materials Science & Engineering 394 (2005) 238-248
7. Jacobus K., Devor R.E., and Kapoor S.G. Machining-induced residual stress; experimentation and modeling. Transaction of the ASME 122 (2000) 20-31
8. Jang D.Y., Watkins T.R., Kozaczek K.J., and Hubbard C.R. Surface residual stress in machined austenitic stainless steel. Wear 194 (1996) 168-173
9. Li W., Preuss M., Withers P.J., Axinte D., and Andrews P. Characterisation of residual stresses in machined surfaces of a high strength nickel-base superalloy. Materials Science Forum 524-525 (2006) 587-592
10. Liu C.R., and Barash M.M. The mechanical state of the sublayer of a surface generated by chip-removal process. Part 1. Cutting with a sharp tool. Transactions of the ASME (1976) 1192-1201
11. Liu C.R., and Barash M.M. The mechanical state of the sublayer of a surface generated by chip-removal process. Part 2. Cutting with a tool with flank wear. Transactions of the ASME (1976) 1202-1208
12. Ordas N., Penalva M.L., Fernandez J., and Garcia-Rosales C. Residual stresses in tool steel due to hard-turning. Journal of Applied Crystallography 36 (2003) 1135-1143
13. Ozel T., and Zeren E. Finite element modeling the influence of edge roundness on the stress and temperature fields induced by high-speed machining. International Journal of Advanced Manufacturing Technology Published online (2006)
14. Prevey P.S. The effect of cold work on the thermal stability of residual compression in surface enhanced IN718. Proceedings of the 20th ASM Materials Solutions conference & Exposition. St. Louis, MO (2000)
15. Sasahara H., Obikawa T., and Shirakashi T. Prediction model of surface residual stress within a machined surface by combining two orthogonal plane models. International Journal of Machine Tools & Manufacture 44 (2004) 815-822
16. Sharman A.R.C., Hughes J.I., and Ridgeway K. An analysis of the residual stresses generated in Inconel 718 when turning. Journal of Materials Processing Technology 173 (2006) 359-367