Surface roughness analysis in high-speed drilling of unreinforced and reinforced polyamides

Journal of Composite Materials

Volumn 46, Issue 21, 2012, Pages 2659-2673

  Gaitonde, V N ^a   Karnik, S R ^a   Rubio, J Campos ^b   Abrao A M ^b   Correia, A Esteves ^c   Davim, J Paulo ^d  

^a KLE TECHNOLOGICAL UNIVERSITY   (India)

^b FEDERAL UNIVERSITY OF MINAS GERAIS   (Brazil)

^c POLYTECHNIC INSTITUTE OF VISEU   (Portugal)

^d UNIVERSITY OF AVEIRO   (Portugal)

Author keywords

high speed drilling; Polymer composites; response surface methodology; surface roughness

Indexed keywords

AVERAGE SURFACE ROUGHNESS; CEMENTED CARBIDES; CENTERLINES; CUTTING SPEED; FEED-RATES; FULL FACTORIAL DESIGN; HIGH SPEED CUTTING; HIGH-SPEED; PARAMETRIC ANALYSIS; POLYMER COMPOSITE; REINFORCED FIBERS; RESPONSE SURFACE METHODOLOGY; ROUGHNESS ANALYSIS; SURFACE FINISHES; THIRD-ORDER;

AMIDES; DESIGN OF EXPERIMENTS; GLASS FIBERS; MATHEMATICAL MODELS; SURFACE PROPERTIES; SURFACE ROUGHNESS;

REINFORCEMENT;

EID: 84868228158     PISSN: 00219983     EISSN: 1530793X     Source Type: Journal    
DOI: 10.1177/0021998311431640     Document Type: Article

References (26)

1. Gaitonde VN, Karnik SR, Mata F, Davim JP. Study on some aspects of machinability in unreinforced and reinforced polyamides. J Compos Mater. 2009 ; 43 (7). 725-739
2. Mata F, Reis P, Davim JP. Physical cutting model of polyamide composites (PA66 GF30). Mater Sci For. 2006 ; 514-516: 643-647
3. Davim JP, Mata F. Comparative evaluation of the turning of reinforced and unreinforced polyamide. Int J Adv Manuf Technol. 2007 ; 33: 911-914
4. Gaitonde VN, Karnik SR, Mata F, Davim JP. Taguchi approach for achieving better machinability in unreinforced and reinforced polyamides. J Reinf Plast Compos. 2008 ; 27: 909-924
5. Gaitonde VN, Karnik SR, Mata F, Davim JP. Modeling and analysis of machinability characteristics in PA6 and PA66 GF30 polyamides through artificial neural network. J Thermplast Compos Mater. 2010 ; 23: 313-336
6. Mohan NS, Ramachandra A, Kulkarni SM. Influence of process parameters on cutting force and torque during drilling of glass-fiber polyester reinforced composites. Compos Struct. 2005 ; 71: 407-413
7. Clark RL, Craven MD, Kander RG. Nylon 66/poly (vinyl pyrrolidone) reinforced composites: 2- Bulk mechanical properties and moisture effects. Composites Part A. 1999 ; 30 (1). 37-48
8. Bhattacharya D, Horrigan DPW. A study of hole drilling in Kelvar composites. Compos Sci Technol. 1998 ; 58: 267-283
9. Khashaba UA. Delamination in drilling GFR thermoset composites. Compos Struct. 2004 ; 63: 313-327
10. Tsao CC, Hocheng H. Effects of special drill bits on drilling-induced delamination of composite materials. Int J Mach Tools Manuf. 2006 ; 46 (12-13). 1403-1416
11. Davim JP, Rubio JC, Abrão AM. A novel approach based on digital image analysis to evaluate the delamination factor after drilling composite laminates. Compos Sci Technol. 2007 ; 67: 1939-1945
12. Davim JP, Reis P, Lapa V, Antonio CC. Machinability study on polyetheretherketone (PEEK) unreinforced and reinforced (GF30) for application in structural components. Compos Struct. 2003 ; 62: 67-73
13. Aoyama E, Nobe H, Hirogaki T. Drilled hole damage of small diameter in printed wiring board. J Mater Process Technol. 2001 ; 118: 436-441
14. Palanikumar K, Karunamoorthy L, Manoharan N. Mathematical model to predict the surface roughness on the machining of glass fiber reinforced polymer composites. J Reinf Plast Compos. 2006 ; 25: 407-417
15. Guu H, Hocheng H, Tai NH, Liu SY. Effect of electrical discharge machining on the characteristics of carbon fiber reinforced carbon composites. J Mater Sci. 2001 ; 36: 2037-2043
16. Persson E, Eriksson I, Zackrisson L. Effect of hole machining defects on strength and fatigue life of composite laminates. Composites Part A. 1997 ; 28 (2). 141-151
17. Lin SC, Chen IK. Drilling of carbon fiber-reinforced composite material at high speed. Wear. 1996 ; 194: 156-162
18. Gaitonde VN, Karnik SR, Rubio JC, Correia AE, Abrao AM, Davim JP. Analysis of parametric influence on delamination in high-speed drilling of carbon fiber reinforced plastic composites. J Mater Process Technol. 2008 ; 203: 431-438
19. Karnik SR, Gaitonde VN, Rubio JC, Correia AE, Abrao AM, Davim JP. Delamination analysis in high-speed drilling of carbon fiber reinforced plastics (CFRP) using artificial neural network model. Mater Des. 2008 ; 29: 1768-1776
20. Benardos PG, Vosniakos GC. Predicting surface roughness in machining: A review. Int J Mach Tools Manuf. 2003 ; 43: 833-844
21. Feng CXJ, Wang X. Development of empirical models for surface roughness prediction in finish turning. Int J Adv Manuf Technol. 2002 ; 20: 348-356
22. Thomas TR Rough surfaces. 2 nd ed. London: Imperial College Press, 1999. London: Imperial College Press ; 1999 :
23. Montgomery DC Design and analysis of experiments. New York: John Wiley and Sons ; 2003:
24. Davim JP, Silva LR, Festas A, Abrão AM. Machinability Study on precision turning of PA66 polyamide with and without glass fiber reinforcing. Mater Des. 2009 ; 30: 228-234
25. Tondon S, Jain VK, Kumar P, Rajurkar P. Investigations into machining of composites. Prec Eng. 1990 ; 12(4): 227-238
26. Rahman M, Ramakrishnan S, Prakash JRS, Ten DCG. Machinability study of carbon fiber reinforced composite. J Mater Process Technol. 1999 ; 89-90: 292-297