Effects of special drill bits on drilling-induced delamination of composite materials

International Journal of Machine Tools and Manufacture

Volumn 46, Issue 12-13, 2006, Pages 1403-1416

  Hocheng, H ^a   Tsao, C C ^b  

^a NATIONAL TSING HUA UNIVERSITY   (Taiwan)

^b Tahua Institute of Technology   (Taiwan)

Author keywords

Composite material; Delamination; Drilling; Special drill; Ultrasonic C Scan

Indexed keywords

DELAMINATION; DRILLING; FIBER REINFORCED PLASTICS; FORCE CONTROL; MACHINING; NUMERICAL METHODS; ULTRASONIC TESTING;

CANDLE STICK DRILL; FEED RATE; SPECIAL DRILL; ULTRASONIC C-SCAN;

DRILLS;

EID: 33746335056     PISSN: 08906955     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijmachtools.2005.10.004     Document Type: Article

References (61)

1. S.R. Ravishankar, C.R.L. Murthy, Modeling drill induced delaminations in composite laminates, in: Proceedings of 14th World Conference on Non-Destructive Testing, vol. 2, Oxford and IBH Publishing, 1996, pp. 489-494.
2. T.L. Wong, S.M. Wu, G.M. Croy, An analysis of delamination in drilling composite materials, in: Proceedings of 14th SAMPE Technology Conference, Atlanta, GA, USA, 1982, pp. 471-483.
3. Persson E., Eriksson I., and Zackrisson L. Effects of hole machining defects on strength and fatigue life of composite laminates. Composites Part A 28 2 (1997) 141-151
4. Capello E., and Tagliaferri V. Drilling damage of GFRP and residual mechanical behavior-part II: static and cyclic bearing load. Journal of Composites Technology Research 23 2 (2001) 131-137
5. Galloway D.F. Some experiments on the influence of various factors on drill performance. Transactions of ASME 79 (1957) 191-237
6. Russell W.R. Drill design and drilling conditions for improved efficiency. ASTME Paper No. 397 (1962) 62
7. Caprino G., and Tagliaferri V. Damage development in drilling glass fiber reinforced plastics. International Journal of Machine Tools & Manufacturing 35 6 (1995) 817-829
8. Ravishankar S.R., and Murthy C.R.L. Characteristics of AE signals obtained during drilling composite laminates. NDT&E International 33 (2000) 341-348
9. J.P. Channani, J.A. Boldt, Manufacturing methods for composite graphite hole generation, SAE Technical Paper Series No. 821418, 1982.
10. Sakuma K., Yokoo Y., and Seto M. Study on drilling of reinforced plastics-relation between tool material and wear behavior. Bulletin of JSME 27 228 (1984) 1237-1244
11. Miller J.A. Drilling graphite/epoxy at lockheed. American Machinist & Automated Manufacturing 131 10 (1987) 70-71
12. Hickey J. Drilling graphite composites. Modern Machine Shop 3 (1987) 85-90
13. Sackey S.M., and Owusu-Ofori S.P. A dynamic modeling technique for damage progression in drilling of composite laminates. Transactions of the North American Manufacturing Research Institute of SME 32 (2004) 71-78
14. Friend C.A., Clyne R.W., and Valentine G.G. Machining graphite composite materials. In: Noton B.R. (Ed). Composite Materials in Engineering Design (1973), ASM Press 217-224
15. Tagliaferri V., Di Ilio A., and Crivelli V.I. Laser cutting of fiber-reinforced polyesters. Composites 16 4 (1985) 317-325
16. 2S aramid/epoxy laminates. Composites 20 2 (1989) 115-119
17. Caprino G., and Tagliaferri V. Maximum cutting speed in laser cutting of fiber reinforced plastics. International Journal of Machine Tools & Manufacturing 28 4 (1988) 389-398
18. Hocheng H. A failure analysis of water jet drilling in composite laminates. International Journal of Machine Tools & Manufacturing 30 3 (1990) 423-429
19. Hashish M. Machining of advanced composites with abrasive-water jets. Manufacturing Review 2 2 (1989) 142-150
20. Miller G.E. Special theory of ultrasonic machining. Journal of Applied Physics 28 2 (1957) 149-156
21. Soundararajan V., and Radhakrishnan V. An experimental investigation on the basic mechanisms involved in ultrasonic machining. International Journal of Machine Tools & Manufacturing 26 3 (1986) 307-321
22. Hocheng H., and Hsu C.C. Preliminary study of ultrasonic drilling of fiber-reinforced plastics. Journal of Materials Processing Technology 48 (1995) 255-266
23. Lau W.S., Wang M., and Lee W.B. Electrical discharge machining of carbon fiber composite materials. International Journal of Machine Tools & Manufacturing 30 2 (1990) 297-308
24. Friedrich M.O., Burant R.O., and McGinty M.J. Cutting tools/drills: part 5-point styles and applications. Manufacturing Engineering 83 (1979) 29-31
25. Haggerty W.A., and Ernst H. The spiral point drill-self-centering drill point geometry. ASTE Paper No. 101 (1958) 58
26. Koplev A., Lystrup A., and Vorm P. The cutting process, chips and cutting forces in machining CFRP. Composites 14 4 (1983) 371-376
27. Veniali F., Llio A., and Tagliaferri V. An experimental study of the drilling of aramid composites. Transactions of ASME Journal of Energy Resources Technology 117 (1995) 271-278
28. Doran J.H., and Maikish C.R. Machining boron composite. In: Noton B.R. (Ed). Composite Materials in Engineering Design (1973), ASM Press 242-250
29. S.M. Wu, J.M. Shen, L.H. Chen, Multifacet drills, in: Proceedings of 14th SAMPE Technology Conference, Atlanta, GA, USA, 1982, pp. 456-463.
30. Koenig W., Grass P., Heintze A., Okcu F., and Schmitz-justin C. Developments in drilling, contouring composites containing Kevlar. Production Engineer 9 (1984) 56-61
31. Koenig W., Wulf C., Grass P., and Willerscheid H. Machining of fiber reinforced plastics. Annals of the CIRP 34 2 (1985) 536-548
32. Jain S., and Yang D.C.H. Effects of feedrate and chisel edge on delamination in composite drilling. Transactions of ASME Journal of Engineering for Industry 115 (1993) 398-405
33. Jain S., and Yang D.C.H. Delamination-free drilling of composite laminates. Transactions of ASME Journal of Engineering for Industry 116 (1994) 475-481
34. Won M.S., and Dharan C.K.H. Chisel edge and pilot hole effects in drilling composite laminates. Transactions of ASME Journal of Manufacturing Science and Engineering 124 (2002) 242-247
35. Won M.S., and Dharan C.K.H. Drilling of aramid and carbon fiber polymer composites. Transactions of ASME Journal of Manufacturing Science and Engineering 124 (2002) 778-783
36. Tsao C.C., and Hocheng H. The effect of chisel length and associated pilot hole on delamination when drilling composite materials. International Journal of Machine Tools & Manufacturing 43 11 (2003) 1087-1092
37. Capello E. Workpiece damping and its effect on delamination damage in drilling thin composite laminates. Journal of Materials Processing Technology 148 2 (2004) 186-195
38. Enemuoh E.U., El-Gizawy A.S., and Okafor A.C. An approach for development of damage-free drilling of carbon fiber reinforced thermosets. International Journal of Machine Tools & Manufacturing 41 12 (2001) 1795-1814
39. David J.P., and Reis P. Study of delamination in drilling carbon fiber reinforced plastics (CFRP) using design experiments. Composite Structures 59 4 (2003) 481-487
40. David J.P., and Reis P. Drilling carbon fiber reinforced plastics manufactured by autoclave-experimental and statistical study. Materials and Design 24 5 (2003) 315-324
41. Ramkumar J., Malhotra S.K., and Krishnamurthy R. Effect of workpiece vibration on drilling of GFRP laminates. Journal of Materials Processing Technology 152 3 (2004) 329-332
42. Zhang Q.X., and Sun S. Study on ultrasonic vibration drilling in carbon fiber reinforced polymers. Chinese Journal of Mechanical Engineering 7 1 (1994) 72-77
43. Zhang L.B., Wang L.J., Liu X.Y., Zhao H.W., Wang X., and Luo H.Y. Mechanical model for predicting thrust and torque in vibration drilling fiber-reinforced composite materials. International Journal of Machine Tools & Manufacturing 41 5 (2001) 641-657
44. Wang L.P., and Wang L.J. Prediction and computer simulation of dynamic thrust and torque in vibration drilling. Proceedings of the Institution of Mechanical Engineers Part B 212 6 (1998) 489-497
45. Zhang L.B., Wang L.J., and Wang X. Study on vibration drilling of fiber reinforced plastics with hybrid variation parameters method. Composite Part A 34 3 (2003) 237-244
46. Wang X., Wang L.J., and Tao J.P. Investigation on thrust in vibration drilling of fiber-reinforced plastics. Journal of Materials Processing Technology 148 2 (2004) 239-244
47. Komanduri R. Machining fiber-reinforced plastics. ASME Mechanical Engineering 4 (1993) 58-64
48. Hosur M.V., Murthy C.R.L., Ramamurthy T.S., and Anita S. Estimation of impact-induced damage in CFRP laminates through ultrasonic imaging. NDT&E International 31 5 (1998) 359-374
49. H. Hocheng, C.C. Tsao, Computerized tomography for evaluation of drilling-induced delamination of composite materials by various drill, in: Proceedings of Sixth ESDA Conference, Istanbul, Turkey, 2002.
50. H. Hocheng, C.C. Tsao, Assessment of delamination by computerized tomography and C-Scan in drilling of composite materials, in: Proceedings of Sixth ICPCG, Xian, China, 2002.
51. Tsao C.C., and Hocheng H. Computerized tomography and C-Scan for measuring delamination in drilling of composite material using various drills. International Journal of Machine Tools & Manufacture 45 11 (2005) 1282-1287
52. The Center for Aviation & Space Technology of Industrial Technology Research Institute, private communication regarding material test, 2004.
53. Khashaba U.A. Delamination in drilling GFR-thermoset composites. Composite Structures 63 (2004) 313-327
54. Shaw M.C., and Oxford Jr. C.J. On the drilling of metals part II: the torque and thrust in drilling. Transactions of ASME 79 (1957) 139-148
55. Shaw M.C. Metal Cutting Principles (1984), Oxford, New York
56. Hocheng H., and Puw H.Y. Machinability of fiber-reinforced thermoplastics in drilling. Transactions of ASME Journal of Engineering Materials and Technology 115 (1993) 146-149
57. Hocheng H., and Dharan C.K.H. Delamination during drilling in composite laminates. Transactions of ASME Journal of Engineering for Industry 112 (1990) 236-239
58. Hocheng H., and Tsao C.C. Comprehensive analysis of delamination in drilling of composite materials with various drill bits. Journal of Materials Processing Technology 140 (2003) 335-339
59. DiPaolo G., Kapoor S.G., and DeVor R.E. An experimental investigation of the crack growth phenomenon for drilling of fiber-reinforced composite materials. Transactions of ASME Journal of Engineering for Industry 118 (1996) 104-110
60. Hocheng H., and Tsao C.C. Analysis of delamination in drilling composite materials using core drill. Australasian Journal of Mechanical Engineering 1 1 (2003) 49-53
61. Timoshenko S., and Woinowsky-Keiger S. Theory of Plates and Shells. second ed. (1959), McGraw-Hill, New York