Experimental study of real roughness attenuation in rolling/sliding concentrated contacts

Tribology International

Volumn 46, Issue 1, 2012, Pages 14-21

  Sperka P ^a   Kirupka I ^a   Hartl, M ^a  

^a BRNO UNIVERSITY OF TECHNOLOGY   (Czech Republic)

Author keywords

Elastohydrodynamic lubrication; Rolling sliding; Roughness attenuation

Indexed keywords

ELASTOHYDRODYNAMIC LUBRICATION; FILM THICKNESS; SURFACE MEASUREMENT;

ATTENUATION PRINCIPLE; CONCENTRATED CONTACTS; EXPERIMENTAL VERIFICATION; FOURIER DECOMPOSITION; HARMONIC COMPONENTS; LUBRICATED CONTACTS; ROLLING-SLIDING; ROLLING-SLIDING CONDITIONS;

SURFACE ROUGHNESS;

EID: 84857037879     PISSN: 0301679X     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.triboint.2011.06.006     Document Type: Article

References (40)

1. Zhu D, Ai XL. Point contact EHL based on optically measured three-dimen-sional rough surfaces. ASME J Tribol 1997;119:375-84.
2. Holmes MJA, Evans HP, Snidle RW. Analysis of mixed lubrication effects in simulated gear tooth contacts. ASME J Tribol 2005;127:61-9.
3. Morales-Espejel GE, Lugt PM, Van Kuilenburg J, Tripp JH. Effect of surface micro-geometry on the pressures and internal stresses of pure rolling EHL contact. Trib Trans 2003;46:260-72.
4. Greenwood JA, Johnson KL. The behavior of transverse roughness in sliding elastohydrodynamically lubricated contacts. Wear 1992;153(1):107-17.
5. Hooke CJ. Surface roughness modification in EHL line contacts the effect of roughness wavelength,orientation and operating conditions.In:Dowson D, editor. Lubrication at the frontier-the role of the interface and surface layers in the thin film and boundary regime,Proceedings of the 25th leeds-lyon symposium ontribology,Tribologyseries.Amsterdam:Elsevier;1999. p. 193-202.
6. Venner CH, Lubrecht AA. Amplitude reduction of non-isotropic harmonic patterns in circular EHL contacts under pure rolling. In: Dowson D, editor. Lubrication at the frontier -the role of the interface and surface layers in the thin film and boundary regime, Proceedings of the 25th leeds-lyon sympo-sium on tribology, Tribology series. Amsterdam: Elsevier; 1999. p. 151-62.
7. Venner CH, Hooke CJ. Surface roughness attenuation in line and point contacts. Proc Inst Mech Eng Part J: J Eng Tribol 2000;214:439-44.
8. Venner CH, Lubrecht AA. An engineering tool for the quantitative prediction of general roughness deformation in EHL contacts based on harmonic waviness attenuation. Proc Inst Mech Eng Part J: J Eng Tribol 2005;219: 303-12.
9. Hooke CJ,Li KY.Rapid calculation of the pressures and clearances in rough elastohydrodynamically lubricated contacts under pure rolling:Part1-low amplitude, sinusoidal roughness.Proc IMech E, PartC: J Mech Eng Sci 2006;220:901-14.
10. Hooke CJ, Li KY. Rapid calculation of the pressures and clearances in rough EHL contacts. Part 2: General roughness. Proc IMechE, Part C: J Mech Eng Sci 2006;220:915-26.
11. Venner CH, Kaneta M, Lubrecht AA. Surface roughness in elastohydrodyna-mically lubricated contacts. In: Dowson D, editor. Thinning films and tribological interfaces, Proceedings of the 26th leeds-lyon symposium on tribology, Tribology series. Amsterdam: Elsevier; 2000. p. 25-36.
12. Greenwood JA, Morales-Espejel GE. The behaviour of transverse roughness in EHL contacts. Proc Inst Mech Eng Part J: J Eng Tribol 1994;208:121-32.
13. Greenwood JA, Morales-Espejel GE, et al. The amplitude of the complemen-tary function for wavy EHL contacts. Tribol Ser, Elsevier 1997;32:307-12.
14. Lubrecht AA. Influence of Local and Global Features in EHL Contacts. Tribol Ser, Elsevier 1997;32:17-25.
15. Lubrecht AA, Graille D, Venner CH, Greenwood JA. Waviness amplitude reduction in EHL line contacts under rolling-sliding. ASME J Tribol 1998;120:705-9.
16. Hooke CJ. The effect of roughness in EHL contacts. In: Dowson D, editor. Life cycle tribology, Proceedings of the 31st leeds-lyon symposium on tribology, Tribology series. Amsterdam: Elsevier; 2005. p. 31-46.
17. Hooke CJ. Roughness in rolling-sliding elastohydrodynamic lubricated con-tacts. Proc Inst Mech Eng Part J: J Eng Tribol 2006;220:259-71.
18. Hooke CH. The behaviour of low-amplitude surface roughness under line contacts: Non-Newtonian fluids. Proc IMechE, Part J, J Eng Tribol 2000;214:253-65.
19. Hooke CJ, Li KY, Morales-Espejel G. Rapid calculation of the pressures and clearances in rough, rolling-sliding elastohydrodynamically lubricated con-tacts. Part 1: Low-amplitude, sinusoidal roughness. Proc IMechE, Part C: J Mech Eng Sci 2007;221:535-50.
20. Hooke CJ, Li KY, Morales-Espejel G. Rapid calculation of the pressures and clearances in rough, rolling-sliding elastohydrodynamically lubricated con-tacts. Part 2: General, non-sinusoidal roughness. Proc IMechE, Part C: J Mech Eng Sci 2007;221:551-64.
21. Hooke CJ. Engineering analysis of rough elastohydrodynamically lubricated contacts. Proc IMechE, Part C: J Mech Eng Sci 2009;223:517-28.
22. Venner CH, Morales-Espejel GE. Amplitude reduction of small-amplitude waviness in transient elastohydrodynamically lubricated line contacts. Proc Inst Mech Eng Part J: J Eng Tribol 1999;213:487-504.
23. Jacod B, Lugt P, Dumont ML, Tripp JH, Venner CH. Amplitude reduction of waviness in elastohydrodynamic lubrication using an Eyring fluid model. Proc Inst Mech Eng Part J: J Eng Tribol 2000;214:343-50.
24. Chapkov AD, Venner CH, Lubrecht AA. Roughness amplitude reduction under non-newtonian EHD lubrication conditions. ASME J Tribol 2006;128:753-60.
25. Venner CH, Berger G, Lugt PM. Waviness deformation in starved EHL circular contacts. ASME J Tribol 2004;126:248-57.
26. Labiau A, Ville F, Sainsot P, Querlioz E, Lubrecht T. Effect of simusoidal surface roughness under starved conditions on rolling contact fatigue. Proc Inst Mech Eng Part J: J Eng Tribol 2008;222:193-200.
27. Guangteng G, Cann PM, Olver AV, Spikes HA. Lubricant film thickness in rough surface, mixed elastohydrodynamic contact. J Tribol 2000;122:65-76.
28. Glovnea RP, Choo JW, Olver AV, Spikes HA. Compression of a single transverse ridge in a circular elastohydrodynamic contact. J Tribol 2003;125: 275-82.
29. Kaneta M, Tani N, Nishikawa H. Optical interferometric observations of the effect of moving transverse asperities on point contact EHL films. In: Tribological research and design for engineering systems, Proceedings of the 29th leeds-lyon symposium on tribology, Tribology and Interface Engineering Series, vol. 41 Elsevier; 2003. pp. 101-109.
30. Félix-Quiñonez A, Ehret P, Summers JL. New experimental results of a single ridge passing through an EHL conjunction. J Tribol 2003;125:252-9.
31. Choo JW, Glovnea RP, Olver AV, Spikes HA. The effects of three-dimensional model surface roughness features on lubricant film thickness in EHL contacts. J Tribol 2003;125:533-42.
32. Félix-Quiñonez A, Ehret P, Summers JL, Morales-Espejel GE. Fourier analysis of a single transverse ridge passing through an elastohydrodynamically lubricated rolling contact: A comparison with experiment. Proc Inst Mech Eng Part J: J Eng Tribol 2004;218(1):33-43.
33. Félix-Quiñonez A, Ehret P, Summers JL. On three-dimensional flat-top defects passing through an EHL point contact: A comparison of modeling with experiments. J Tribol 2005;127:51-60.
34. Choo JW, Olver AV, Spikes HA. The influence of transverse roughness in thin film, mixed elastohydrodynamic lubrication. Tribol Int 2007;40:220-32.
35. Šperka P, Křupka I, Hartl M. Experimental study of real roughness attenuation in concentrated contacts. Tribol Int 2010;43:1893-901.
36. Hartl M, Křupka I, Polišcǔk R, Liška M, Molimard J, Vergne P, et al. Thin film colorimetric interferometry. Tribol Trans 2001;44:270-6.
37. Crane R. Interference phase measurement. Appl Opt 1969;8:538.
38. Hariharan PBF, Oreb ATE. Digital phase-shifting interferometry: A simple error-compensating phase calculation algorithm. Appl Opt 1987;26:2504.
39. Schwider JC, Burow R, Elssner KE, Grzanna J, Spolaczyk, Merkel K. Digital wave-front measuring interferometry: Some systematic error sources. Appl Opt 1983;22:3421-32.
40. Ghiglia DC, Pritt MD. Two-dimensional phase unwrapping: Theory, algorithms, and software. A Wiley-Interscience publ; 0-471-24935-1.