Procedure to perform a validated incremental hole drilling measurement: Application to shot peening residual stresses

Strain

Volumn 47, Issue SUPPL. 1, 2011, Pages

  Valentini, E ^a   Beghini, M ^b   Bertini, L ^b   Santus, C ^b   Benedetti, M ^c  

^a SINT Technology Srl   (Italy)

^b UNIVERSITY OF PISA   (Italy)

^c UNIVERSITY OF TRENTO   (Italy)

Author keywords

incremental hole drilling method; shot peening residual stresses; X ray diffraction

Indexed keywords

BENDING STRESS; BENDING STRESS DISTRIBUTION; CYLINDRICAL SHAPES; EXTERNAL LOADS; HOLE DRILLING; INCREMENTAL HOLE DRILLING METHOD; OFFSET CORRECTIONS; REAL TIME; RESIDUAL STRESS PREDICTION; STRESS CALCULATIONS; TEST RIGS; TESTING PROCEDURE; UNIAXIAL STRESS;

DIFFRACTION; INSTRUMENTS; RESIDUAL STRESSES; SHOT PEENING; STRESS CONCENTRATION; X RAY DIFFRACTION;

STRESS MEASUREMENT;

EID: 79958804698     PISSN: 00392103     EISSN: 14751305     Source Type: Journal    
DOI: 10.1111/j.1475-1305.2009.00664.x     Document Type: Article

References (31)

1. ASTM (2001) Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method. ASTM E837-01e1, ASTM International, West Conshohocken, PA.
2. Lu, J,. (1996) Handbook of Measurement of Residual Stresses. Society for Experimental Mechanics, The Fairmon Press Inc., Indian Trail Liburn, GA.
3. Schajer, G. S., (1988) Measurement of non-uniform residual stresses using the hole-drilling method. Part I. Stress calculation procedures. J. Eng. Mater. Technol. 110, 338-343.
4. Schajer, G. S., (1988) Measurement of non-uniform residual stresses using the hole-drilling method. Part II. Practical application of the integral method. J. Eng. Mater. Technol. 110, 344-349.
5. Schajer, G. S., (2007) Hole-drilling residual stress profiling with automated smoothing. J. Eng. Mater. Technol. 129, 440-445. (Pubitemid 47229447)
6. Aoh, J. N., and, Wei, C. S., (2002) On the improvement of calibration coefficients for hole-drilling integral method. Part I. Analysis of calibration coefficients obtained by a 3-D FEM model. J. Eng. Mater. Technol. 124, 250-258.
7. ASTM (2008) Standard Test Method for Determining Residual Stresses by the Hole-Drilling Strain-Gage Method. ASTM E837-08, ASTM International, West Conshohocken, PA.
8. Schajer, G. S., and, Altus, E., (1996) Stress calculation error analysis for incremental hole-drilling residual stress measurements. J. Eng. Mater. Technol. 118, 120-126. (Pubitemid 126759937)
9. Stefanescu, D., Truman, C. E., Smith, D. J., and, Whitehead, P. S., (2006) Improvements in residual stress measurement by the incremental centre hole drilling technique. Exp. Mech. 46, 417-427.
10. Vangi, D., (1994) Data management for the evaluation of residual stresses by the incremental hole drilling method. J. Eng. Mater. Technol. 116, 561-566.
11. Zuccarello, B., (1999) Optimal calculation steps for the evaluation of residual stress by the incremental hole drilling method. Exp. Mech. 39, 117-124. (Pubitemid 29403088)
12. Aoh, J. N., and, Wei, C. S., (2003) On the improvement of calibration coefficients for hole-drilling integral method. Part II. Experimental validation of calibration coefficients. J. Eng. Mater. Technol. 125, 107-115.
13. Grant, P. V., Lord, P. D., and, Whitehead, P. S., (2002) The Measurement of Residual Stresses by the Incremental Hole Drilling Technique. National Physical Laboratory Teddington, Middlesex. Measurement good practice guide 53.
14. Beghini, M., and, Bertini, L., (2000) Analytical influence functions for variable residual stress measurement by the hole drilling. J. Strain Anal. Eng. Des. 35, 125-135.
15. Beghini, M., Bertini, L., and, Rosellini, W., (2000) Genetic algorithms for variable through thickness residual stress evaluation. In: Residual Stress ECRS 5. Vols. 347-349 (, A. J. Böttger, R. Delhez, and, E. J. Mittemeijer, Eds). Trans Tech Publications, Switzerland. Materials Science Forum, 144-149.
16. Fontanari, V., Frendo, F., Bortolamedi, T., and, Scardi, P., (2005) Comparison of the hole-drilling and X-ray diffraction methods for measuring the residual stresses in shot peened Al-alloys. J. Strain Anal. Eng. Des. 40, 199-200.
17. Lord, J. D., Fry, A. T., and, Grant, P. V., (2002) A UK Residual Stress Intercomparison Exercise-An Examination of the XRD and Hole Drilling Techniques. NPL, Project CPM4.5 Measurement of Residual Stress in Components. NPL Report MATC(A)98.
18. Noyan, I. C., and, Cohen, J. B., (1987) Residual Stress Measurement by Diffraction and Interpretation. Springer-Verlag, New York.
19. Prevey, P. S., (1990) X-ray diffraction characterisation of residual stresses produced by shot peening. In: Shot Peening Theory and Application (IITT-International, Ed.). Gournay sur Marne, France, 81-93.
20. Dong, Y. H., and, Scardi, P., (2000) Marq X-new program for whole powder pattern fitting. J. Appl. Crystallogr. 33, 184-189. (Pubitemid 32142177)
21. Benedetti, M., Bortolamedi, T., Fontanari, V., and, Frendo, F., (2004) Bending fatigue behaviour of differently shot peened Al 6082 T5 alloy. Int. J. Fatigue 26, 889-897.
22. Hilley, M. E., ed (1971) Residual stress measurement by X-ray diffraction, SAE J 784a, Soc. of Auto. Engrs. 21-24.
23. Rendler, N. J., and, Vigness, I., (1966) Hole-drilling stain-gauge method of measuring residual stresses. Exp. Mech. 6, 577-586.
24. ASTM (2003) Standard Test Methods for Performance Characteristics of Metallic Bonded resistance Strain Gages. ASTM E 251-92, ASTM International, West Conshohocken, PA.
25. Valentini, E., (1994) An automatic system for measuring non-uniform residual stress by the hole drilling method. In: XIII IMEKO World Congress, Torino, Italy: 1904-1909.
26. Valentini, E,., Benedetti, M,., Fontanari, V,., Beghini, M,., Bertini, L., and, Santus, C,. (2007) Fine increment hole-drilling method for residual stress measurement, proposal of a calibrating apparatus. Book Experimental Analysis of Nano and Engineering Materials and Structures. Springer, Netherlands: 945-946. doi; ISBN 978-1-4020-6238-4 (Print), 978-1-4020-6239-1 (Online).
27. Flaman, M. T., and, Herring, J. A., (1986) Ultra high speed center hole technique for difficult machining. Exp. Tech. 10, 34-35.
28. Scafidi, M,., Valentini, E., and, Zuccarello, B,. (2007) Effetti del raggio di raccordo al fondo foro nella analisi delle tesnioni residue con il metodo della rosetta forata. In: XXXVI Convegno Nazionale AIAS (, B. Iavarone, and, M. Cristina Amedeo, Eds). Cuzzolin Editore, Ischia (Naples), 4-8. ISBN: 978-88-87998-75-7.
29. Schwarzer, J., Schulze, V., and, Vöhringer, O,. (2003) Finite element simulation of shot peening-a method to evaluate the influence of peening parameters on surface characteristics. In: Shot Peening, Proceedings ICSP-8 (, L. Wagner, Ed.), ISBN 3-527-30537-8. Wiley-VCH, Munich, Germany: S. 508-515.
30. Nobre, J. P., Dias, A. M., Gibmeier, J., and, Kornmeier, M., (2006) Local stress-ratio criterion for incremental hole-drilling measurements of shot-peening stresses. J. Eng. Mater. Technol. 128, 193-201.
31. Beghini, M., Bertini, L., and, Raffaelli, P., (1994) Numerical analysis of plasticity effects in the hole-drilling residual stress measurement. J. Test. Eval. 22, 522-529.