On the improvement of calibration coefficients for hole-drilling integral method: Part II - Experimental validation of calibration coefficients

Journal of Engineering Materials and Technology

Volumn 125, Issue 2, 2003, Pages 107-115

  Aoh, Jong Ning ^a   Wei, Chung Sheng ^a  

^a NATIONAL CHUNG CHENG UNIVERSITY   (Taiwan)

Author keywords

[No Author keywords available]

Indexed keywords

BENDING STRENGTH; CALCULATIONS; CALIBRATION; FINITE ELEMENT METHOD; INTEGRAL EQUATIONS; MATHEMATICAL MODELS; MECHANICAL TESTING; RESIDUAL STRESSES;

CALIBRATION COEFFICIENTS; EXPERIMENTAL VALIDATION; HOLE DRILLING; PLATE THICKNESS; STRESS MEASUREMENT;

DRILLING;

EID: 0038078465     PISSN: 00944289     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1543972     Document Type: Article

References (20)

1. Mathar, J., 1934, "Determination of Initial Stresses by Measuring the Deformations Around Drilled Holes," Trans. ASME, 56, pp. 249-254.
2. Kelsey, R. A., 1956, "Measuring Non-Uniform Residual Stresses by the Hole-drilling Method," Proceedings of SESA, 14(1), pp. 181-194.
3. Rendler, N. J., and Vigness, I., 1966, "Hole Drilling Strain Gage Method of Measuring Residual Stresses," Exp. Mech., 6(12), pp. 577-586.
4. Bathgate, R. G., 1968, "Measurement of Non-Uniform Biaxial Residual Stresses by the Hole-Drilling Method," Strain, 4(2), pp. 20-29.
5. Schajer, G. S., 1988, "Measurement of Non-Uniform Residual stresses Using the Hole Drilling Method: Part 1-Stress Calculation Procedures," ASME J. Eng. Mater. Technol., 110(4), pp. 318-342.
6. Schajer, G. S., 1988, "Measurement of Non-Uniform Residual Stresses Using the Hole Drilling Method: Part II-Practical Application of the Integral Method," ASME J. Eng. Mater. Technol., 110(4), pp. 344-349.
7. Niku-Lari, A., Lu, J., and Flavenot, J. F., 1985, "Measurement of Residual Stress Distribution by the Incremental Hole-Drilling Method," Exp. Mech., 25(6), pp. 175-185.
8. Flaman, M. T., and Manning, B. H., 1985, "Determination of Residual Stress Variation with Depth by the Hole Drilling Method," Exp. Mech., 25(6), pp. 205-207.
9. Schajer, G. S., 1992, "Non-Uniform Residual Stress Measurements by the Hole Drilling Method," Strain, 28(2), pp. 19-22.
10. Schajer, G. S., 1981, "Application of Finite Element Calculations to Residual Stress Measurements," ASME J. Eng. Mater. Technol., 103, pp. 157-163.
11. Aoh, H. N., and Wei, C. S., 2002, "On the Improvement of Calibration Coefficients for Hole-Drilling Integral Method: Part I-Analysis of Calibration Coefficients Obtained by a Three-Dimensional FEM Model," ASME J. Eng. Mater. Technol., 124(2), pp. 250-258.
12. Schajer, G. S., 1991, "Strain Data Averaging for the Hole Drilling Method," Exp. Tech., 15(2), pp. 25-28.
13. Schajer, G. S., and Altus, E., 1996, "Stress Calculation Error Analysis for Incremental Hole-Drilling Residual Stress Measurements," ASME J. Eng. Mater. Technol., 118(1), pp. 120-128.
14. Ajovalasit, A., 1979, "Measurement of Residual Stresses By the Hole Drilling Method Influence of Hole Eccentricity," J. Strain Anal., 14(4), pp. 171-178.
15. Vangi, D., 1994, "Data Management for the Evaluation of Residual Stresses by the Incremental Hole Drilling Method," ASME J. Eng. Mater. Technol., 116(4), pp. 561-566.
16. Zuccarello, B., 1999, "Optimal Calculation Steps for the Evaluation of Residual Stress by the Incremental Hole-Drilling Method," Exp. Mech., 39(2), pp. 117-124.
17. Aoh, J. N., and Wei, C. S., 2003, "Analysis on the Effect of Hole Geometry on the Residual Stress Measurement Using Integral Hole-Drilling Method," paper submitted to Strain.
18. Zienkiewicz, O. C., 1977, The Finite Element Method, 3rd ed., McGraw-Hill, New York, Chap. 15.
19. Measurements Group, 1993, "Measurement of Residual Stresses by the Hole-Drilling Strain Gage Method," Tech Note-503-4, Measurements Group Inc., Raleigh, NC.
20. Watkins, D. S., 1991, Fundamentals of Matrix Computations, John Wiley & Sons, New York.