On the improvement of calibration coefficients for hole-drilling integral method: Part I - Analysis of calibration coefficients obtained by a 3-D FEM model

Journal of Engineering Materials and Technology

Volumn 124, Issue 2, 2002, Pages 250-258

  Aoh, Jong Ning ^a   Wei, Chung Sheng ^a  

^a NATIONAL CHUNG CHENG UNIVERSITY   (Taiwan)

Author keywords

Calibration Coefficients; Finite Element Analysis; Hole Drilling Method; Integral Method; Residual Stress Measurement

Indexed keywords

BENDING (DEFORMATION); CALIBRATION; COMPUTER SIMULATION; CONVERGENCE OF NUMERICAL METHODS; ELASTIC MODULI; FINITE ELEMENT METHOD; MATHEMATICAL MODELS; RELAXATION PROCESSES; RESIDUAL STRESSES; STRAIN; TENSILE TESTING; THREE DIMENSIONAL; TWO DIMENSIONAL;

CALIBRATION COEFFICIENTS; HOLE-DRILLING METHOD; INTEGRAL METHOD; RESIDUAL STRESS MEASUREMENT;

INTEGRATION;

EID: 0011777025     PISSN: 00944289     EISSN: None     Source Type: Journal    
DOI: 10.1115/1.1416685     Document Type: Article

References (20)

1. Yen, H. J., and Lin, M. C. C., 1995, "Measurement of Residual Stress in the Weld Overlay Piping Components," Exp. Mech., 35, No. 2, pp. 89-95.
2. Roelens, J. B., Maltrud, F., and Lu, J., 1994, "Determination of Residual Stresses in the Submerged Arc Multi-pass Welds by Means of Numerical Simulation and Comparison with Experimental Measurements," Weld. World, 33, No. 3, pp. 152-159.
3. Richard, C. S., Beranger, G., Lu, J., and Flavenol, J. F., 1999, "The Influence of Heat Treatment and Interdiffusion on the Adhesion of Plasma Sprayed NiCrAIY Coatings," Surf. Coal. Technol., 82, pp. 99-109.
4. Smith, David J., and Bonner, Neil W., 1996, "Measurement of Residual Stresses Using the Deep Hole Method," ASME, Pressure Vessels and Piping Division, Vol. 327, pp 53-65.
5. Mathar, J., 1934, "Determination of Initial Stresses by Measuring the Deformations Around Drilled Holes," Trans. ASME, 56, pp. 249-254.
6. ASTM E 837, 1985, "Determining Residual Stresses by the Hole-Drilling Strain-gage Method," American Society for Testing and Materials, Philadelphia, Pa.
7. Kroenke, Holloway, and Mabe, 2000, "Stress Calculation Update in ASTM E 837 Residual Stress Hole Drilling Standard," Advances in Computational Science and Engineering, Vol. 1, pp. 695-701, Atluri and Brust, eds., Aug., Tech Science Press.
8. Rendler, N. J., and Vigness, I., 1966, "Hole Drilling Strain Gage Method of Measuring Residual Stresses," Exp. Mech., 6, No. 12, pp. 577-586.
9. Bathgate, R. G., 1968, "Measurement of Non-uniform Biaxial Residual Stresses by the Hole-Drilling Method," Strain, 4, No. 2, pp. 20-24.
10. Kelsey, R. A., 1956, "Measuring Non-uniform Residual Stresses by the Hole-drilling Method," Proceedings of SESA, Vol. 14, No. 1, pp. 181-194.
11. "Measurement of Residual Stresses by the Hole-Drilling Strain Gage Method," 1993, Tech. Note 503-4. Measurements Group, Raleigh, NC.
12. Schajer, G. S., 1988, "Measurement of Non-Uniform Residual Stresses Using the Hole Drilling Method, Part I - Stress Calculation Procedures," ASME J. Eng. Mater. Technol., 110, No. 4, pp. 318-342.
13. Schajer, G. S., 1988, "Measurement of Non-Uniform Residual Stresses Using the Hole Drilling Method, Part II - Practical Application of the Integral Method," ASME J. Eng. Mater. Technol., 110, No. 4, pp. 344-349.
14. Niku-Lari, A., Lu, J., and Flavenot, J. F., 1985, "Measurement of Residual Stress Distribution by the Incremental Hole-Drilling Method," Exp. Mech., 25, No. 6, pp. 175-185.
15. Flaman, M. T., and Manning, B. H., 1985, "Determination of Residual Stress Variation with Depth by the Hole Drilling Method," Exp. Mech., 25, No. 6, pp. 205-207.
16. Wern, H., 1995, "Measurement of Non-uniform Residual Stresses Using the Hole-drilling Method, A New Integral Formalism," Strain, 31, No. 2, pp. 63-68.
17. Hampton, R. W., and Nelson, D. V., 1992, "On the Use of the Hole-Drilling Technique for Residual Stress Measurement in Thin Plates," ASME J. Pressure Vessel Technol., 114, pp. 292-299.
18. Schajer, G. S., 1981, "Application of Finite Calculations to Residual Stress Measurements," ASME J. Eng. Mater. Technol., 103, No. 2, pp. 157-163.
19. Zienkiewicz, O. C., 1977, The Finite Element Method, 3rd. ed., Chapter 15, McGraw-Hill, New York.
20. SYSWELD, User's Manual, SYSTUS 233, Framasoft + CSI, 1996.