Fault detection of linear bearings in brushless AC linear motors by vibration analysis

IEEE Transactions on Industrial Electronics

Volumn 58, Issue 5, 2011, Pages 1684-1694

  Bianchini, Claudio ^a   Immovilli, Fabio ^a   Cocconcelli, Marco ^a   Rubini, Riccardo ^a   Bellini, Alberto ^a  

^a UNIVERSITY OF MODENA AND REGGIO EMILIA   (Italy)

Author keywords

Bearings; fault detection; linear electric machines; rough surface; signal processing; spectral analysis; wear

Indexed keywords

BEARINGS; ELECTRIC MACHINES; ROUGH SURFACES; SPECTRAL ANALYSIS; WEAR;

AC GENERATOR MOTORS; BEARINGS (STRUCTURAL); ELECTRIC MACHINERY; FAULT DETECTION; LINEAR MOTORS; ROLLER BEARINGS; SIGNAL DETECTION; SIGNAL PROCESSING; SPECTRUM ANALYSIS; SURFACE MEASUREMENT;

VIBRATION ANALYSIS;

EID: 79954536084     PISSN: 02780046     EISSN: None     Source Type: Journal    
DOI: 10.1109/TIE.2010.2098354     Document Type: Article

References (51)

1. A. Bellini, F. Filippetti, C. Tassoni, and G. A. Capolino, "Advances in diagnostic techniques for induction machines" IEEE Trans. Ind. Electron., vol. 55, no. 12, pp. 4109-4126, Dec. 2008.
2. S. Poyhonen, P. Jover, and H. Hyotyniemi, "Signal processing of vibrations for condition monitoring of an induction motor" in Proc. 1st Int. Symp. Control, Commun. Signal Process., 2004, pp. 499-502.
3. S. Nandi, H. Toliyat, and X. Li, "Condition monitoring and fault diagnosis of electrical motors-A review" IEEE Trans. Energy Convers., vol. 20, no. 4, pp. 719-729, Dec. 2005. (Pubitemid 41830047)
4. P. O'Donnell, "Report of large motor reliability survey of industrial and commercial installations, part I and II" IEEE Trans. Ind. Appl., vol. IA-21, no. 4, pp. 853-872, Jul. 1985.
5. A. H. Bonnett, "Root cause ac motor failure analysis with a focus on shaft failures" IEEE Trans. Ind. Appl., vol. 36, no. 5, pp. 1435-1448, Sep./Oct. 2000.
6. O. V. Thorsen and M. Dalva, "A survey of faults on induction motors in offshore oil industry, petrochemical industry, gas terminals, and oil refineries" IEEE Trans. Ind. Appl., vol. 31, no. 5, pp. 1186-1196, Sep./Oct. 1995.
7. M. Melfi, S. Rogers, S. Evon, and B. Martin, "Permanent-magnet motors for energy savings in industrial applications" IEEE Trans. Ind. Appl., vol. 44, no. 5, pp. 1360-1366, Sep./Oct. 2008.
8. C. Bianchini, F. Immovilli, M. Cocconcelli, R. Rubini, and A. Bellini, "Fault diagnosis of linear bearings in brushless ac linear motors" in Proc. IEEE Int. SDEMPED, Aug. 31-Sep. 3, 2009, pp. 1-6.
9. M. E. Badaoui, F. Guillet, and J. Danière, "New applications of the real cepstrum to gear signals, including definition of a robust fault indicator" Mech. Syst. Signal Process., vol. 18, no. 5, pp. 1031-1046, Sep. 2004.
10. J. R. Stack, T. G. Habetler, and R. G. Harley, "Fault-signature modeling and detection of inner-race bearing faults" IEEE Trans. Ind. Appl., vol. 42, no. 1, pp. 61-68, Jan./Feb. 2006. (Pubitemid 43204768)
11. A. Ibrahim, M. El Badaoui, F. Guillet, andW. Youssef, "Electrical signals analysis of an asynchronous motor for bearing fault detection" in Proc. IEEE IECON, Nov. 2006, pp. 4975-4980.
12. M. Pacas, S. Villwock, and R. Dietrich, "Bearing damage detection in permanent magnet synchronous machines" in Proc. IEEE ECCE, Sep. 2009, pp. 1098-1103.
13. S. H. Kia, H. Henao, and G. A. Capolino, "Torsional vibration effects on induction machine current and torque signatures in gearbox-based electromechanical system" IEEE Trans. Ind. Electron., vol. 56, no. 11, pp. 4689-4699, Nov. 2009.
14. B. Trajin, J. Regnier, and J. Faucher, "Comparison between stator current and estimated mechanical speed for the detection of bearing wear in asynchronous drives" IEEE Trans. Ind. Electron., vol. 56, no. 11, pp. 4700-4709, Nov. 2009.
15. J. Faiz and M. Ojaghi, "Instantaneous-power harmonics as indexes for mixed eccentricity fault in mains-fed and open/closed-loop driveconnected squirrel-cage induction motors" IEEE Trans. Ind. Electron., vol. 56, no. 11, pp. 4718-4726, Nov. 2009.
16. B. M. Ebrahimi, J. Faiz, and M. J. Roshtkhari, "Static-, dynamic-, and mixed-eccentricity fault diagnoses in permanent-magnet synchronous motors" IEEE Trans. Ind. Electron., vol. 56, no. 11, pp. 4727-4739, Nov. 2009.
17. W. le Roux, R. G. Harley, and T. G. Habetler, "Detecting rotor faults in low power permanent magnet synchronous machines" IEEE Trans. Power Electron., vol. 22, no. 1, pp. 322-328, Jan. 2007. (Pubitemid 46231785)
18. J. Stack, T. Habetler, and R. Harley, "Fault classification and fault signature production for rolling element bearings in electric machines" IEEE Trans. Ind. Appl., vol. 40, no. 3, pp. 735-739, May/Jun. 2004.
19. B. Trajin, J. Regnier, and J. Faucher, "Comparison between vibration and stator current analysis for the detection of bearing faults in asynchronous drives" IET Elect. Power Appl., vol. 4, no. 2, pp. 90-100, Feb. 2010.
20. F. Andrade, I. Esat, andM. Badi, "Gearbox fault detection using statistical methods, time-frequency methods (STFT and Wigner-Ville distribution) and harmonic wavelet-A comparative study" in Proc. COMADEM, 1999, pp. 77-85.
21. G. Dalpiaz, A. Rivola, and R. Rubini, "Effectiveness and sensitivity of vibration processing techniques for local fault detection in gears" Mech. Syst. Signal Process., vol. 14, no. 3, pp. 387-412, May 2000.
22. A. Jardine, D. Lin, and D. Banjevic, "A review on machinery diagnostics and prognostics implementing condition-based maintenance" Mech. Syst. Signal Process., vol. 20, no. 7, pp. 1483-1510, Oct. 2006.
23. M. Hayes, Statistical Digital Signal Processing and Modeling, M. Hayes, Ed. Hoboken, NJ: Wiley, 1996.
24. R. Curcuru', M. Cocconcelli, F. Immovilli, and R. Rubini, "On the detection of distributed roughness on ball bearings via stator current energy: Experimental results" Diagnostyka, vol. 51, no. 3, pp. 17-21, Mar. 2001.
25. F. Immovilli, M. Cocconcelli, A. Bellini, and R. Rubini, "Detection of generalized-roughness bearing fault by spectral-kurtosis energy of vibration or current signals" IEEE Trans. Ind. Electron., vol. 56, no. 11, pp. 4710-4717, Nov. 2009.
26. B. Trajin, M. Chabert, J. Regnier, and J. Faucher, "Hilbert versus Concordia transform for three-phase machine stator current time- frequency monitoring" Mech. Syst. Signal Process., vol. 23, no. 8, pp. 2648-2657, Nov. 2009.
27. M. Salami, A. Gani, and T. Pervez, "Machine condition monitoring and fault diagnosis using spectral analysis techniques" in Proc. 1st Int. Conf. Mechatronics, 2001, pp. 690-700.
28. J. Taylor and D. Kirkland, The Bearing Analysis Handbook, J. Taylo and D. Kirkland, Eds. Tampa, FL: VCI, 2004.
29. W. Wang and P. McFadden, "Early detection of gear failure by vibration analysis I. Calculation of the time-frequency distribution" Mech. Syst. Signal Process., vol. 7, no. 3, pp. 193-203, May 1993.
30. W.Wang and P. McFadden, "Application of wavelets to gearbox vibration signals for fault detection" J. Sound Vib., vol. 192, no. 5, pp. 927-939, May 1996. (Pubitemid 126373737)
31. M. Blodt, P. Granjon, B. Raison, and G. Rostaing, "Models for bearing damage detection in induction motors using stator current monitoring" IEEE Trans. Ind. Electron., vol. 55, no. 4, pp. 1813-1822, Apr. 2008. (Pubitemid 351585994)
32. T. Harris and M. Kotzalas, Rolling Bearing Analysis, T. Harris and M. Kotzalas, Eds. Boca Raton, FL: CRC, 2006.
33. R. R. Schoen, T. G. Habetler, F. Kamran, and R. G. Bartfield, "Motor bearing damage detection using stator current monitoring" IEEE Trans. Ind. Appl., vol. 31, no. 6, pp. 1274-1279, Nov./Dec. 1995.
34. T. Lindh, J. Ahola, J. Kamarainen, V. Kyrki, and J. Partanen, "Bearing damage detection based on statistical discrimination of stator current" in Proc. 4th IEEE Int. SDEMPED, Aug. 2003, pp. 177-181.
35. P. Lynn, An Introduction to the Analysis and Processing of Signals, P. Lynn, Ed. London: Chem/Mats-Sci/E, 1989.
36. C. Harris and A. Piersol, Harris' Shock and Vibration Handbook, C. Harris and A. Piersol, Eds. New York: McGraw-Hill, 2002.
37. J. Taylor, The Vibration Handbook, J. Taylor, Ed. Tampa, FL: VCI, 2003.
38. Evaluation of Machine Vibration by Measurements on Non-Rotating Parts, ISO 10816-1, Interstate Council For Standardization, Metrology and Certification Std, 1995.
39. R. D. Almeida, S. D. S. Vincente, and L. Padovese, "New technique for evaluation of global vibration levels in rolling bearings" Shock Vib., vol. 9, no. 4/5, pp. 225-234, 2002.
40. S. Goldman, Vibration Spectrum Analysis: A Practical Approach, S. Goldman, Ed. New York: Ind. Press, 1999.
41. J. Stack, R. Harley, and T. Habetler, "An amplitude modulation detector for fault diagnosis in rolling element bearings" IEEE Trans. Ind. Electron., vol. 51, no. 5, pp. 1097-1102, Oct. 2004.
42. R. Randall, J. Antoni, and S. Chobsaard, "The relationship between spectral correlation and envelope analysis in the diagnostics of bearing faults and other cyclostationary machine signals" Mech. Syst. Signal Process., vol. 15, no. 5, pp. 945-962, Sep. 2001. (Pubitemid 33112620)
43. B. Picinbono, "On instantaneous amplitude and phase of signals" IEEE Trans. Signal Process., vol. 45, no. 3, pp. 552-560, Mar. 1997. (Pubitemid 127765943)
44. M. Venouziou and H. Zhang, "Characterizing the Hilbert transform by the Bedrosian theorem" J. Math. Anal. Appl., vol. 338, no. 2, pp. 1477-1481, Feb. 2008.
45. S. Gu, J. Ni, and J. Yuan, "Non-stationary signal analysis and transient machining process condition monitoring" Int. J. Mach. Tools Manufacture, vol. 42, no. 1, pp. 41-51, Jan. 2002. (Pubitemid 33018527)
46. W. Zanardelli, E. Strangas, and S. Aviyente, "Identification of intermittent electrical and mechanical faults in permanent-magnet ac drives based on time-frequency analysis" IEEE Trans. Ind. Appl., vol. 43, no. 4, pp. 971-980, Jul./Aug. 2007. (Pubitemid 47249970)
47. D. Newland, An Introduction to Random Vibrations, Spectral & Wavelet Analysis, D. Newland, Ed. New York: Dover, 2005.
48. W. Staszewski and G. Tomlinson, "Application of the wavelet transform to fault detection in a spur gear" Mech. Syst. Signal Process., vol. 8, no. 3, pp. 289-307, May 1994.
49. A. Miller, "A new wavelet basis for the decomposition of gear motion error signals and its application to gearbox diagnostics" M.S. thesis, Pennsylvania State Univ., University Park, PA, 1999.
50. D. Childers, D. Skinner, and R. Kemerait, "The cepstrum: A guide to processing" Proc. IEEE, vol. 65, no. 10, pp. 1428-1443, Oct. 1977.
51. N. van der Merwe and A. J. Hoffman, "A modified cepstrum analysis applied to vibrational signals" in Proc. 14th Int. Conf. Digital Signal Process., 2002, pp. 873-876.