A three-dimensional heat sink module design problem with experimental verification

International Journal of Heat and Mass Transfer

Volumn 54, Issue 7-8, 2011, Pages 1482-1492

  Huang, Cheng Hung ^a   Lu, Jon Jer ^a   Ay, Herchang ^b  

^a NATIONAL CHENG KUNG UNIVERSITY   (Taiwan)

^b NATIONAL KAOHSIUNG UNIVERSITY OF APPLIED SCIENCES   (Taiwan)

Author keywords

Heat sink module design; Levenberg Marquardt Method; Optimum design

Indexed keywords

CFD-ACE+; COMMERCIAL CODES; EXPERIMENTAL VERIFICATION; FIN ARRAYS; FIN HEIGHT; FIN PITCH; FIN THICKNESS; GENERAL PURPOSE; LEVENBERG-MARQUARDT METHOD; MAXIMUM TEMPERATURE; MODULE DESIGN; NUMERICAL EXPERIMENTS; NUMERICAL SOLUTION; OPTIMUM DESIGNS; THERMAL CAMERA;

COOLING SYSTEMS; FINS (HEAT EXCHANGE); THREE DIMENSIONAL;

DESIGN;

EID: 78751642424     PISSN: 00179310     EISSN: None     Source Type: Journal    
DOI: 10.1016/j.ijheatmasstransfer.2010.11.044     Document Type: Article

References (20)

1. A.D. Kraus, and A. Bar-Cohen Thermal Analysis and Control of Electronic Equipment 1983 Hemisphere Publishing Corporation Washington
2. C.J. Shih, and G.C. Liu Optimal design methodology of plate-fin heat sinks for electronic cooling using entropy generation strategy IEEE Trans. Compon. Packag. Technol. 27 2004 551 559
3. T. Furukawa, W. J. Yang, Reliability of heat sink optimization using entropy generation, in: Proc. 8th AIAA/ASME Joint Thermophysics and Heat Transfer Conf., AIAA-2002-3216 (2002).
4. O.A. Leon, G.D. Mey, E. Dick, and J. Vierendeels Staggered heat sinks with aerodynamic cooling fins Microelectron. Reliab. 44 2004 1181 1187
5. E. Small, S.M. Sadeghipour, and M. Asheghi Heat sinks with enhanced heat transfer capability for electronic cooling applications J. Electron. Pack. 128 2006 285 290
6. M. Iyengar, and A. Bar-Cohen Least-energy optimization of forced convection plate fin heat sinks IEEE Trans. Compon. Packag. Technol. 26 2003 62 70
7. Y.T. Yang, and H.S. Peng Numerical study of pin-fin heat sink with un-uniform fin height design Int. J. Heat Mass Transfer 51 2008 4788 4796
8. Y.T. Yang, and H.S. Peng Numerical study of the heat sink with un-uniform fin width designs Int. J. Heat Mass Transfer 52 2009 3473 3480
9. J.H. Zhou, C.X. Yang, and L.N. Zhang Minimizing the entropy generation rate of the plate-finned heat sinks using computational fluid dynamics and combined optimization Appl. Therm. Eng. 29 2009 872 1879
10. K. Park, and S. Moon Optimal design of heat exchangers using the progressive quadratic response surface model Int. J. Heat Mass Transfer 42 2005 237 244
11. S. Srisomporn, and S. Bureerat Geometrical design of plate-fin heat sinks using hybridization of MOEA and RSM IEEE Trans. Compon. Packag. Technol. 31 2008 351 360
12. A. Shah, B.G. Sammakia, H. Srihari, and K. Ramakrishna Optimization study for a parallel plate impingement heat sink J. Electron. Pack. 128 2006 311 318
13. K. Park, D.H. Choi, and K.S. Lee Numerical shape optimization for high performance of a heat sink with pin-fins Numer. Heat Transfer A 46 2004 909 927
14. B. Sahin, K. Yakut, I. Kotcioglu, and C. Celik Optimum design parameters of a heat exchanger Appl. Energ. 82 2005 90 106
15. D.M. Marquardt An algorithm for least-squares estimation of nonlinear parameters J. Soc. Indust. Appl. Math. 11 1963 431 441
16. C.H. Huang, C.C. Chiang, and S.K. Chou An inverse geometry design problem in optimizing the hull surfaces J. Ship Res. 42 1998 79 85
17. P.F. Chen, and C.H. Huang An inverse hull design approach in minimizing the ship wave Ocean Eng. 31 2004 1683 1712
18. P.F. Chen, C.H. Huang, M.C. Fang, and J.H. Chou An inverse design approach in determining the optimal shape of bulbous bow with experimental verification J. Ship Res. 50 2006 1 14
19. C.H. Huang, and J.W. Lin Optimal gas channel shape design for a serpentine PEMFC - -Theoretical and experimental studies J. Electrochem. Soc. 156 2009 B178 B187
20. CFD-RC user's manual, ESI-CFD Inc., 2005.