Flatness based speed control of drive systems with resonant loads

IECON Proceedings (Industrial Electronics Conference)

Volumn , Issue , 2010, Pages 120-125

  Thomsen, S ^a   Fuchs, F W ^a  

^a UNIVERSITY OF KIEL   (Germany)

Author keywords

[No Author keywords available]

Indexed keywords

CONTROL METHODS; CONTROL OF DRIVE; CONVENTIONAL CONTROL; CONVENTIONAL PI; DESIGN AND ANALYSIS; DIFFERENTIAL FLATNESS; DRIVE SHAFT; DRIVE SYSTEMS; FLATNESS-BASED CONTROL; HIGH DYNAMIC; MECHANICAL OSCILLATIONS; MECHANICAL VIBRATIONS; MODEL-BASED CONTROL METHODS; MOTOR SPEED; NEW MODEL; PROPORTIONAL-INTEGRAL; RESONANT LOAD; SIMULATION AND MEASUREMENT;

CONTROL THEORY; INDUSTRIAL ELECTRONICS; SPEED CONTROL; SPEED REGULATORS;

VIBRATIONS (MECHANICAL);

EID: 78751489433     PISSN: None     EISSN: None     Source Type: Conference Proceeding    
DOI: 10.1109/IECON.2010.5675188     Document Type: Conference Paper

References (38)

1. R. Dhaouadi, K. Kubo, and M. Tobise, "Two-degree-of-freedom robust speed controller for high-performance rolling mill drives," Industry Applications, IEEE Transactions on, vol. 29, no. 5, pp. 919-926, Sept./Oct. 1993.
2. Y. Hori, H. Sawada, and Y. Chun, "Slow resonance ratio control for vibration suppression and disturbance rejection in torsional system," Industrial Electronics, IEEE Transactions on, vol. 46, no. 1, pp. 162-168, Feb. 1999.
3. S. K. Salman and A. L. J. Teo, "Windmill modeling consideration and factors influencing the stability of a grid-connected wind power-based embedded generator," Power Systems, IEEE Transactions on, vol. 18, no. 2, pp. 793-802, May 2003.
4. N. Amann, J. Böcker, and F. Prenner, "Active damping of drive train oscillations for an electrically driven vehicle," Mechatronics, IEEE/ASME Transactions on, vol. 9, no. 4, pp. 697-700, Dec. 2004.
5. G. Götting and R. De Doncker, "Active drive control of electric vehicles using a modal state observer," in IEEE Power Electronics Specialists Conference Record, vol. 6, June 2004, pp. 4585-4590.
6. G. Ellis and R. Lorenz, "Resonant load control methods for industrial servo drives," in IEEE Industry Applications Conference Record, vol. 3, 2000, pp. 1438-1445.
7. A. Hace, K. Jezernik, and A. Šabanović, "SMC with disturbance observer for a linear belt drive," Industrial Electronics, IEEE Transactions on, vol. 54, no. 6, pp. 3402-3412, Dec. 2007.
8. S. Beineke, F. Schütte, H. Wertz, and H. Grotstollen, "Comparison of parameter identification schemes for self-commissioning drive control of nonlinear two-mass systems," in IEEE Industry Applications Conference Record, vol. 1, Oct. 1997, pp. 493-500.
9. G. Zhang, "Speed control of two-inertia system by PI/PID control," Industrial Electronics, IEEE Transactions on, vol. 47, no. 3, pp. 603-609, June 2000.
10. S. Preitl and R.-E. Precup, "An extension of tuning relations after symmetrical optimum method for PI and PID controllers," Automatica, vol. 35, no. 10, pp. 1731 - 1736, 1999.
11. M. Cychowski and K. Szabat, "Model predictive speed control with optimal torque constraints handling of drive systems with elastic transmission," in IEEE Electric Machines and Drives Conference Record, May 2009, pp. 251-258.
12. K. Szabat and T. Orlowska-Kowalska, "Vibration suppression in a two-mass drive system using PI speed controller and additional feedbacks - comparative study," Industrial Electronics, IEEE Transactions on, vol. 54, no. 2, pp. 1193-1206, April 2007.
13. R. Dhaouadi, K. Kubo, and M. Tobise, "Analysis and compensation of speed drive systems with torsional loads," Industry Applications, IEEE Transactions on, vol. 30, no. 3, pp. 760-766, May/June 1994.
14. J.-K. Ji and S.-K. Sul, "Kalman filter and LQ based speed controller for torsional vibration suppression in a 2-mass motor drive system," Industrial Electronics, IEEE Transactions on, vol. 42, no. 6, pp. 564-571, Dec. 1995.
15. R. Zhang, Z. Chen, Y. Yang, and C. Tong, "Torsional vibration suppression control in the main drive system of rolling mill by state feedback speed controller based on extended state observer," in IEEE Control and Automation Conference Record, June 2007, pp. 2172-2177.
16. K. Szabat and T. Orlowska-Kowalska, "Performance improvement of industrial drives with mechanical elasticity using nonlinear adaptive kalman filter," Industrial Electronics, IEEE Transactions on, vol. 55, no. 3, pp. 1075-1084, March 2008.
17. S. Thomsen and F. W. Fuchs, "Speed control of torsional drive systems with backlash," in Power Electronics and Applications Conference Record, Sept. 2009.
18. P. Korondi, H. Hashimoto, and V. Utkin, "Discrete sliding mode control of two mass system," in IEEE Industrial Electronics Symposium, vol. 1, 1995, pp. 338-343.
19. P. Korondi, H. Hashimoto, and V. Utkin, "Direct torsion control of flexible shaft in an observer-based discrete-time sliding mode," Industrial Electronics, IEEE Transactions on, vol. 45, no. 2, pp. 291-296, April 1998.
20. K. Erenturk, "Nonlinear two-mass system control with sliding-mode and optimised proportional-integral derivative controller combined with a grey estimator," Control Theory & Applications, IET, vol. 2, no. 7, pp. 635-642, July 2008.
21. ∞ control with a nonlinear observer for a two-mass system," Industry Applications, IEEE Transactions on, vol. 39, no. 3, pp. 637-644, May/June 2003.
22. M. Cychowski, K. Delaney, and K. Szabat, "Low-cost high-performance predictive control of drive systems with elastic coupling," in Power Electronics and Motion Control Conference Record, Sept. 2008, pp. 2241-2247.
23. N. Hoffmann, S. Thomsen, and F. W. Fuchs, "Model based predictive speed control of a drive system with torsional loads - a practical approach," in Power Electronics and Motion Control Conference. EPE-PEMC, Sept. 2010, accepted for publication.
24. N. Hoffmann, S. Thomsen, and F. W. Fuchs, "Appropriate tuning and robust design of a generalized predictive speed controller for drive systems with resonant loads," in Energy Conversion Congress and Exposition, 2010. ECCE 2010. IEEE, Sept. 2010, accepted for publication.
25. S. Thomsen, N. Hoffmann, and F. W. Fuchs, "Comparative study of conventional PI-control, PI-based state space control and model based predictive control for drive systems with elastic coupling," in Energy Conversion Congress and Exposition, 2010. ECCE 2010. IEEE, Sept. 2010, accepted for publication.
26. A. Chelouah, E. Delaleau, P. Martin, and P. Rouchon, "Differential flatness and control of induction motors," in Proceedings CESAŠ96, vol. 1, 1996, pp. 80-85.
27. P. Martin and P. Rouchon, "Flatness and sampling control of induction motors," in 13th Triennial World Congress, 1996, pp. 389-394.
28. E. Delaleau, J.-P. Louis, and R. Ortega, "Modeling and control of induction motors," Int. J. Appl. Math. Comput. Sci., vol. 11, no. 1, pp. 105-129, 2001.
29. V. Hagenmeyer, A. Ranftl, and E. Delaleau, Flatness-based control of the induction drive minimising energy dissipation. Springer, 2003, pp. 149-160.
30. J. Dannehl and F. Fuchs, "Flatness-based control of an induction machine fed via voltage source inverter - concept, control design and performance analysis," in IEEE Industrial Electronics, IECON 2006 - 32nd Annual Conference on, Nov. 2006, pp. 5125 -5130.
31. W.-L. Jin, "A method for computing quadratic brunovsky forms," Electronic Journal of Linear Algebra, ELA, vol. 13, pp. 40-55, Feb. 2005.
32. M. Fliess, J. Lévine, P. Martin, and P. Rouchon, "On differentially flat nonlinear systems," in Proceedings of the IFAC-Symposium on Nonlinear Control Systems, Bordeaux, 1992, pp. 408-412.
33. M. Fliess, J. Lévine, P. Martin, and P. Rouchon, "Flatness and defect of non-linear systems: introductory theory and examples," Int. J. Control, vol. 61, no. 6, pp. 1327-1361, 1995.
34. V. Hagenmeyer and E. Delaleau, "Robustness analysis with respect to exogenous perturbations for flatness-based exact feedforward linearization," Automatic Control, IEEE Transactions on, vol. 55, no. 3, pp. 727-731, March 2010.
35. K. Graichen, "Feedforward control design for finite-time transition problems of nonlinear systems with input and output constraints," Ph.D. dissertation, Universität Stuttgart, 2006.
36. V. Hagenmeyer, "Robust nonlinear tracking control based on differential flatness," Ph.D. dissertation, Université Paris Sud, 2003.
37. J. Rudolph, Flatness Based Control of Distributed Parameter Systems. Shaker Verlag, Aachen, 2003.
38. T. Meurer and M. Zeitz, "Two-degree-of-freedom tracking control design for boundary controlled distributed parameter systems using formal power series," in IEEE Decision and Control Conference Record, vol. 3, Dec. 2004, pp. 3307-3312.