Nondestructive characterization of the surface integrity of cold surface hardened components

Production Engineering

Volumn 4, Issue 5, 2010, Pages 443-449

  Meyer, D ^a   Kruse, D ^a   Bobe, A ^a   Goch, G ^a   Brinksmeier, E ^a  

^a UNIVERSITY OF BREMEN   (Germany)

Author keywords

Nondestructive; Photothermal; Surface hardening; X ray diffraction

Indexed keywords

COLD SURFACE; DESTRUCTIVE METHODS; FUNCTIONAL PERFORMANCE; GEAR WHEEL; MEASURING METHOD; NEAR-SURFACE LAYERS; NON DESTRUCTIVE; NON-DESTRUCTIVE TECHNIQUE; NONDESTRUCTIVE CHARACTERIZATION; PENETRATION DEPTH; PHOTO-THERMAL; RESIDUAL STRESS PROFILES; SUBSURFACE PROPERTIES; SURFACE HARDENING; SURFACE HARDNESS; SURFACE INTEGRITY;

DIFFRACTION; HARDENING; HARDNESS; SURFACE PROPERTIES; X RAY DIFFRACTION;

SURFACE TESTING;

EID: 77958589734     PISSN: 09446524     EISSN: 18637353     Source Type: Journal    
DOI: 10.1007/s11740-010-0228-3     Document Type: Article

References (30)

1. Lonardo PM, Lucca DA, De Chiffre L (2002) Emerging trends in surface metrology. Ann CIRP 51(2): 701-723.
2. Lucca DA, Brinksmeier E, Goch G (1998) Progress in assessing surface and subsurface integrity. Ann CIRP 47(2): 669-693.
3. Field M, Kahles JF (1971) Review of surface integrity of machined components. Ann CIRP 20(2): 153-163.
4. Novovic D, Dewes RC, Aspinwall DK, Voice W, Bowen P (2004) The effect of machined topography and integrity on fatigue life. Int J Mach Tools Manuf 44(2-3): 125-134.
5. Brockhoff T, Brinksmeier E (1999) Grind-hardening: a comprehensive view. Ann CIRP 48(1): 255-260.
6. Kristoffersen H, Vomacka P (2001) Influence of process parameters for induction hardening on residual stresses. Mater Des 22(8): 637-644.
7. Karpuschewski B (1995) Mikromagnetische Randzonenanalyse geschliffener einsatzgehärteter Bauteile, Dr.-Ing. Dissertation, University of Hannover.
8. Denkena B, Becker JC, Breidenstein B, Spille C (2004) Micromagnetic material characterization of thin steel sheet. Ann Ger Acad Soc Prod Eng (WGP) XI(2): 43-46.
9. Goch G, Walther HG, Thwaite EG (1998) Reconstruction of depth-dependent parameter profiles based on photothermal measurements. Ann CIRP 47(1): 483-486.
10. Goch G, Schmitz B, Geerkens J, Karpuschewski B, Reigl M, Sprongl P, Ritter R (1999) Review of non-destructive measuring methods for the assessment of surface integrity: a survey of new measuring methods for coatings, layered structures and processed surfaces. Precis Eng 23: 9-33.
11. Hirsch T, Wohlfahrt H, Macherauch E (1987) Fatigue strength of case hardened and shot peened gears. In: Wohlfahrt H, Kopp R, Vöhringer O (eds) Shot peening: science, technology, application. DGM Informationsgesellschaft, Oberursel, pp 547-560.
12. Kobayashi M, Matsui T, Murakami Y (1998) Mechanism of creation of compressive residual stress by shot peening. Int J Fatigue 20(5): 351-357.
13. Schuhbauer H-G, Bäuerle H, Müller-Stock H-W (1991) Schwingfestigkeitssteigerung schwerer Maschinenbauteile durch Schlagverfestigen. Konferenz-Einzelbericht: Moderne Fertigungs-technologien zur Lebensdauersteigerung, 17. Vortragsveranstaltung des DVM-Arbeitskreises Betriebsfestigkeit, pp 53-64.
14. Hacini L, van Lê N, Bocher P (2008) Effect of impact energy on residual stresses induced by Hammer Peening of 304L plates. J Mater Process Technol 208(1-3): 542-548.
15. El-Axir MH (2000) An investigation into deep rolling. Int J Mach Tools Manuf 40: 1603-1617.
16. Röttger K (2003) Walzen hartgedrehter Oberflächen. Dissertation Dr.-Ing. RWTH Aachen, Shaker Verlag, Aachen.
17. Brinksmeier E, Garbrecht M, Meyer D (2008) Cold surface hardening. Ann CIRP 57(1): 541-544.
18. Garbrecht M (2006) Mechanisches Randschichthärten in der Fertigung, Dr.-Ing. Dissertation, University of Bremen.
19. Brinksmeier E, Garbrecht M, Meyer D, Dong J (2008) Surface hardening by strain induced martensitic transformation. Ann Ger Acad Soc Prod Eng (WGP) 2: 109-116.
20. Meyer D, Dong J, Garbrecht M, Hoffmann F, Brinksmeier E, Zoch H-W (2010) Mechanisch induziertes Härten. J Heat Treat Mater (HTM), accepted for publication in 2010.
21. Goch G, Seidel U, Schmitz B, Reigl M, Walther HG, Lan TTN (1996) Photothermal hardness measurement for shafts. Bearings and Gears. Düsseldorf, VDI Verlag, pp 1031-1042.
22. Reigl M (1997) Methoden zur Quantifizierung photothermischer Signale, Dr.-Ing. Dissertation, Ulm.
23. Kruse D, Prekel H, Goch G (2008) Berührungslose Messung von Einhärtetiefen mittels photothermischer Randzonenanalyse. XXII. Messtechnisches Symposium des Arbeitskreises der Hochschullehrer für Messtechnik e. V. (AHMT). J. Czarske. Aachen, Shaker Verlag, pp 181-192.
24. Goch G, Steiner R, Reick M, Schmitz B (1995) Photothermal detection of surface defects and thermal changes in near-surface layers. In: Balageas, Busse, Carlomagno (eds) Quantitative infrared thermography. Editions Europeenes Thermique et Industrie, Paris, pp 293-297.
25. Kruse D, Prekel H, Goch G, Walther HG (2007) Correlation between hardening depth and thermal parameters based on photothermal measurements. Proc Estonian Acad Sci-Eng 13(4): 423-435.
26. Kruse D, Prekel H, Goch G (2006) Automated photothermal detection of burning and hardening depth. 9th International Conference on Infrared Sensors & Systems, Nürnberg, pp 341-346.
27. Mandelis A (1994) Nondestructive evaluation, vol II. Progress in Photothermal and Photoacoustic Science and Technology, PTR Prentice Hall.
28. Goch G, Prekel H, Patzelt S, Ströbel G, Lucca DA, Stock HR, Mehner A (2004) Nondestructive and contactless determination of layer thickness and thermal properties of PVD and sol-gel layers by photothermal methods. Ann CIRP 53(1): 471-474.
29. Kruse D, Prekel H, Goch G (2006) Photothermische Randzonenuntersuchung an wärmebehandelten Stählen und Objekten mit thermischer Schädigung. 13. ITG-/GMA-Fachtagung. Freiburg, Berlin, VDE Verlag, pp 173-177.
30. Hertz H (1881) Über die Berührung fester elastischer Körper. J für die reine und angewandte Mathematik 92: 156-171.