Determination of the heat transfer coefficient from short-shots studies and precise simulation of microinjection molding

Polymer Engineering and Science

Volumn 50, Issue 1, 2010, Pages 165-173

  Tham, Nguyen Chung ^a   Jüttner, Gábor ^b   Löser, Cindy ^a   Pham, Tung ^c   Gehde, Michael ^a  

^a CHEMNITZ UNIVERSITY OF TECHNOLOGY   (Germany)

^b Kunststoff Zentrum in Leipzig GmbH   (Germany)

^c BOREALIS POLYOLEFINE GMBH   (Austria)

Author keywords

[No Author keywords available]

Indexed keywords

ASPECT RATIO; COMMINUTION; FILLING; HEAT TRANSFER COEFFICIENTS; MICROCAVITIES; MOLDING; REVERSE ENGINEERING;

FILLING DEGREE; FILLING PROCESS; FILLING STAGE; FLOW BEHAVIOURS; HEAT TRANSFER CO-EFFICIENTS; INJECTION PRESSURES; MICRO CAVITIES; MICRO-INJECTION MOULDINGS; PRECISE SIMULATION; PRESSURE DEPENDENT VISCOSITY;

MOLDS;

EID: 73349089002     PISSN: 00323888     EISSN: 15482634     Source Type: Journal    
DOI: 10.1002/pen.21536     Document Type: Article

References (23)

1. L. Yu, C.G. Koh, L.J. Lee, and. K.W. Koelling, Polym. Eng. Sci., 42, 871 (2002).
2. C.-H. Wu and S.-H. Wu, J. Polym. Eng., 27, 107 (2007).
3. D.S. Kim, K.C. Lee, T.H. Kwon, and S.S. Lee, J. Micro-mech. Microeng., 12, 236 (2002).
4. A. Cramer, W. Michaeli, W. Friesenbichler, and I. Duretek, Zeitschrift Kunststofftechnik (WAK), 3, 1 (2007).
5. V.-W. Wang, Dynamic Simulation With Graphics for the Injection Molding of Three-Dimensional Thin Parts, PhD thesis, Cornell University, New York (1985).
6. M. Koponen, J. Enqvist, T. Nguyen-Chung, and G. Mennig, Polym. Eng. Sci., 48, 711 (2008).
7. R. Blum, Verbesserte Temperaturkontrolle beim Kunststoffspritzgieß en, PhD thesis, RWTH Aachen University, Aachen (1993).
8. K. Ainoya and O. Amano, ANTEC, 726 (2001).
9. C.J. Yu, J.E. Sunderland, and C. Poli, Polym. Eng. Sci., 30, 1599 (1990).
10. D. Delaunay, P. Le Bot, R. Fulchiron, J.F. Luye, and G. Regnier, Polym. Eng. Sci., 40, 1682 (2000).
11. R. Brunotte, Die thermodynamischen und verfahrenstechnischen Abläufe der in-situ-Oberflächenmodifizierung beim Spritzgießen, PhD thesis, Chemnitz University of Technology, Chemnitz (2006).
12. J. Greener and R. Wimberger-Friedl, Eds., "Injection Molding for Microfluidics Applications, " Precision Injection Molding - Process, Materials, and Applications, Chapter 8, 169, Hanser, Munich (2006).
13. B.O Rhee, C.A Hieber, and K.K Wang, ANTEC, 496 (1994).
14. H.L. Zhang, N.S. Ong, and Y.C. Lam, Polym. Eng. Sci., 47, 2012 (2007).
15. D. Yao and B. Kim, J. Micromech. Microeng., 12, 604 (2002).
16. R.L. Golf, G. Poutot, D. Delaunay, R. Fulchiron, and E. Koscher, Int. J. Heat Mass Tran., 48, 5417 (2005).
17. J.F. Dijksman and G.D.C Kuiken, Eds., IUTAM Symposium on Numerical Simulation of Non-Isothermal Flow of Visco-elastic Liquids, Kluwer, Dordrecht, (1995).
18. D.C Venerus, J.D Schieber, V. Balasubramanian, K. Bush, and S. Smoukov, Phys. Rev. Lett., 93, 098301-1 (2004).
19. S.C. Dai and R.I. Tanner, Rheol. Acta, 45, 228 (2006).
20. T. Nguyen-Chung, G. Jüttner, T. Pham, G. Mennig, and M. Gehde, Zeitschrift Kunststofftechnik (WAK), 4, 1 (2008).
21. N.N., Moldflow Plastics Insight, Online manual, Moldflow Corp., Framingham, MA (2008).
22. G. Jüttner, Kunststoffe, 94, 53 (2004).
23. P. Kennedy, Flow Analysis of Injection Molds, Hanser