Nature of contact between polymer and mold in injection molding. Part I: influence of a non-perfect thermal contact

Polymer Engineering and Science

Volumn 40, Issue 7, 2000, Pages 1682-1691

  Delaunay, D ^a   Le Bot, P ^a   Fulchiron, R ^b   Luye, J F ^c   Regnier, G ^c  

^a Centre National de la Recherche Scientifique   (France)

^b UNIVERSITÉ LYON 1   (France)

^c ARTS ET MÉTIERS PARISTECH   (France)

Author keywords

[No Author keywords available]

Indexed keywords

ATMOSPHERIC PRESSURE; HEAT FLUX; INTERFACES (MATERIALS); ORGANIC POLYMERS; SENSORS; TEMPERATURE; TEMPERATURE DISTRIBUTION; THERMODYNAMIC PROPERTIES;

HEAT FLUX DENSITY; THERMAL CONTACT; THERMAL SENSORS;

INJECTION MOLDING;

EID: 0034230163     PISSN: 00323888     EISSN: None     Source Type: Journal    
DOI: 10.1002/pen.11300     Document Type: Article

References (20)

1. C. J. Yu, J. E. Sunderland, and C. Poli, Polym. Eng. Sci., 30, 1599 (1990).
2. S. K. Parihar and N. T. Wright, Int. Com. in Heat and Mass Transf., 24, 1083 (1997)
3. O. Rhee, Cornell Injection Molding Program, Technical report no. 80 (1994).
4. J. J. Salgon, F. Robe-Valloire, J. Blouet, and J. Bransier, Int. J. Heat Mass Transfer. 40, 1121 (1997).
5. G. C. Peischl and I. Brucker, Polym. Eng. Sci., 29, 202 (1989)
6. O. Amano and S. Utsugi, Polym. Eng. Sci., 29, 171 (1989).
7. O. Amano and S. Utsugi, Polym. Eng. Sci., 30, 385 (1990).
8. M. Lallemand and A. Soufiani, Revue générate de thermique, 34, 69 (1995).
9. G. Y. Lai and J. X. Rietveld, Polym. Eng. Sci., 36, 1755 (1996).
10. C. Maler, Polym. Eng. Sci., 36, 1502 (1996).
11. J. P. Bardon and Y. Jarny, Patent no 94.01996 (1994).
12. J. V. Beck, B. Backwell, and C. St Clair, Inverse Heat Conduction, Wiley-Interscience (1985).
13. S. Quiellet, P. Le Bot, D. Delaunay, and Y. Jarny, ASME Proceedings of the 32nd National Heat Conference, 2, 9, Baltimore (1997).
14. A. Benard and G. Advani, Int. J. Heat Mass Transfer, 38, 819 (1995).
15. Sommier, T. Jurkowski, D. Delaunay, and Y. Jarny, High Temperatures-High Pressures, 30, 159 (1998).
16. C. A. Hieber, Int. Polym. Proc,. 12, 249 (1997).
17. H. Ito, Y. Tsutusmi, K. Minagawa, J. Takimoto, and K. Koyama, Colloid Polym. Sci., 273, 811 (1995).
18. P. Le Bot, Phd thesis, ISITEM-University of Nantes, France (1998).
19. M. R. Kamal and E. Chu, Polym. Eng. Sci., 23, 27 (1983).
20. G. Regnier, D. Delaunay, P. Le Bot, and J. F. Luye, Injection Molding of Polypropylene: Influence of Mold Cooling Time on Residual Stresses and Shrinkages, IUPAC Congress, Brisbane, Australia (July 1998).